Airspace class

The world's navigable airspace is divided into three-dimensional segments, each of which is assigned to a specific class. Most nations adhere to the classification specified by the International Civil Aviation Organization and described below, though they might use only some of the classes defined below, and significantly alter the exact rules and requirements. Similarly, individual nations may also designate special use airspace with further rules for reasons of national security or safety.

Abbreviations used in this article

Abbreviation	Full name	Description
ATC	Air Traffic Control	A service provided by ground-based controllers who direct aircraft on the ground and through controlled airspace, and can provide advisory services to aircraft in non-controlled airspace. The primary purpose of ATC worldwide is to prevent collisions, organize and expedite the flow of air traffic, and provide information and other support for pilots.
ATZ	Aerodrome Traffic Zone	Circular zones around an airport with a radius based on the length of the runway
CTA	Control Area	A controlled airspace which extends from a lower limit to an upper limit.
CTR	Control Zone	A controlled airspace extending upwards from the surface to an upper limit.
FLxxx	Flight Level	Defined as a vertical altitude at standard atmospheric pressure, nominally expressed in hundreds of feet. Flight levels are usually designated in writing as FLxxx, where xxx is a two or three-digit number indicating the pressure altitude in units of 100 feet. In radio communications, FL290 would be pronounced as "flight level two nine zero." The phrase "flight level" makes it clear that this refers to the standardized pressure altitude.
ICAO	International Civil Aviation Organization	A specialized agency of the United Nations. It codifies the principles and techniques of international air navigation and fosters the planning and development of international air transport to ensure safe and orderly growth
IFR	Instrument Flight Rules	A set of regulations that concern flying by reference to instruments in the flight deck, and where navigation accomplished by reference to electronic signals.
MATZ	Military Aerodrome Traffic Zone	A version of ATZ for military air bases.
SVFR	Special Visual Flight Rules	A set of aviation regulations under which a pilot may operate an aircraft. It's a special case of operating under visual flight rules where a VFR flight cleared by air traffic control to operate within a control zone in meteorological conditions that are poorer than visual meteorological conditions.
TCA	Terminal Control Area	A control area normally established at the confluence of ATS Routes in the vicinity of one or more major aerodromes.
TMA	Terminal Manoeuvring Area	A designated area of controlled airspace surrounding a major airport where there is a high volume of traffic.
TRSA	Terminal Radar Service Area	A delimited airspace in which radar and air traffic control services are made available to pilots flying under instrument flight rules or visual flight rules for the purposes of maintaining aircraft separation.
VFR	Visual Flight Rules	A set of regulations under which a pilot operates an aircraft in weather conditions generally clear enough to allow the pilot to see where the aircraft is going

ICAO definitions

On March 12, 1990, ICAO adopted the current airspace classification scheme. The classes are fundamentally defined in terms of flight rules and interactions between aircraft and air traffic control. Generally speaking, the ICAO airspaces allocate the responsibility for avoiding other aircraft, namely either to ATC or to the aircraft commander.
Some key concepts are:

Separation: Maintaining a specific minimum distance between an aircraft and another aircraft or terrain to avoid collisions, normally by requiring aircraft to fly at set levels or level bands, on set routes or in certain directions, or by controlling an aircraft's speed.
Clearance: Permission given by ATC for an aircraft to proceed under certain conditions contained within the clearance.
Traffic Information: Information given by ATC on the position and, if known, intentions of other aircraft likely to pose a hazard to flight.
Flight Rules: Aircraft can operate under visual flight rules or instrument flight rules. There is also an intermediate form, special visual flight rules.
ICAO adopted classifications

Note: These are the ICAO definitions. Country-specific adaptations are discussed in the sections below.

Class A: All operations must be conducted under IFR. All aircraft are subject to ATC clearance. All flights are separated from each other by ATC.
Class B: Operations may be conducted under IFR, SVFR, or VFR. All aircraft are subject to ATC clearance. All flights are separated from each other by ATC.
Class C: Operations may be conducted under IFR, SVFR, or VFR. All aircraft are subject to ATC clearance. Aircraft operating under IFR and SVFR are separated from each other and from flights operating under VFR, but VFR flights are not separated from each other. Flights operating under VFR are given traffic information in respect of other VFR flights.
Class D: Operations may be conducted under IFR, SVFR, or VFR. All flights are subject to ATC clearance. Aircraft operating under IFR and SVFR are separated from each other, and are given traffic information in respect of VFR flights. Flights operating under VFR are given traffic information in respect of all other flights.
Class E: Operations may be conducted under IFR, SVFR, or VFR. Aircraft operating under IFR and SVFR are separated from each other, and are subject to ATC clearance. Flights under VFR are not subject to ATC clearance. As far as is practical, traffic information is given to all flights in respect of VFR flights.
Class F: Operations may be conducted under IFR or VFR. ATC separation will be provided, so far as practical, to aircraft operating under IFR. Traffic Information may be given as far as is practical in respect of other flights.
Class G: Operations may be conducted under IFR or VFR. ATC has no authority but VFR minimums are to be known by pilots. Traffic Information may be given as far as is practical in respect of other flights.

Special Airspace: these may limit pilot operation in certain areas. These consist of Prohibited areas, Restricted areas, Warning Areas, MOAs, Alert areas and Controlled firing areas, all of which can be found on the flight charts.
Classes A–E are referred to as controlled airspace. Classes F and G are uncontrolled airspace.
The table below provides an overview of the above classes, and the specifications for each.

Class	Controlled	IFR	SVFR	VFR	ATC clearance	Separation	Traffic information
A					Required	Provided for all flights	N/A
B					Required	Provided for all flights	N/A
C					Required	Provided for all IFR/SVFR to IFR/SVFR/VFR	Provided for all VFR
D					Required	Provided for IFR/SVFR to other IFR/SVFR	Provided for all IFR and VFR
E					Required for IFR and SVFR	Provided for IFR/SVFR to other IFR/SVFR	Provided for all IFR and VFR flights where possible
F					Advisory only	Provided for IFR/SVFR to other IFR/SVFR where possible	Provided where possible if requested
G					Not provided	Not provided	Provided where possible if requested

Use of airspace classes

Each national aviation authority determines how it uses the ICAO classifications in its airspace design. In some countries, the rules are modified slightly to fit the airspace rules and air traffic services that existed before the ICAO standardisation.

Australia

has adopted a civil airspace system based on the United States National Airspace System :

Class A is used above FL 180 along the populated coastal areas, and above FL 245 elsewhere.
Class B is not used.
Class C is used in a 360° funnel shape in the Terminal Control Zones of the major international airports, extending up to the base of the Class A, generally at FL 180 over these airports. It also overlays Class D airspace at smaller airports.
Class D is used for the Terminal Control Zones of medium-sized airports, extending from the surface up to AGL. Above this, Class C airspace is used, although generally only in a sector, and not 360° around the airport.
Class E is used along the populated coastal areas, from to the base of the overlying Class A or Class C airspace.
Class F is not used.
Class G is used wherever other classes are not—almost always from the surface to the base of the overlying Class A, C, D or E airspace.
Transition from GAAP to Class D

Australia used to have a non-standard class of airspace for use at the capital city general aviation airports, called a General Aviation Airport Procedures Zone. A control tower provided procedural clearances for all aircraft inside the zone. Additionally, any aircraft operating within of the zone must obtain a clearance. VFR aircraft arrive and depart using standard arrival and departure routes, while instrument arrival and departure procedures are published for IFR operations. During visual meteorological conditions, IFR aircraft are not provided with full IFR services. During instrument meteorological conditions, or marginal VMC, VFR operations are restricted in order to facilitate full IFR service for IFR aircraft.
As of the 3rd of June 2010, all GAAP aerodromes were changed to Class D aerodromes, and the previous Class D procedures were changed. The new Class D procedures are similar to the FAA Class D procedures. VFR Aircraft are no longer required to enter the airspace via set inbound/outbound points, however can be directed there by ATC. VFR and IFR aircraft now require taxi clearance in the "manoeuvring area" of the aerodrome, but can still taxi within set apron areas without a clearance. IFR aircraft now receive slot times and the visibility requirements of Special VFR are reduced from 3000m Visibility to 1600m.

Canada

There are seven airspace classes in use in Canada, but the letters do not always correspond with ICAO definitions.

Denmark

Class A is generally used above FL195.
Class B is not used.
Class C is used for busy terminal areas, namely Billund TMA and København TMA. All airspace above FL195 is also class C.
Class D is used for all control zones and most terminal areas.
Class E is generally used for all airspace from 3500 feet to FL195, with the exception of TMA's and airspace over the North Sea.
Class F is not used.
Class G is used below 3500 feet, except around controlled airports, and below FL195 over the North Sea.
Estonia

In Estonia, airspace is divided into only classes C, D and G.

Class C is used for enroute airspace, between FL095 and FL 660.
Class D is used for the Ämari CTR, and Tartu TMA and CTR, during operational hours.
Class G is used below FL095, In the Kurassaure, Parnu, and Kardla FIZs, and Tartu TMA & CTR, outside of operational hours.
Germany

In Germany, Classes A and B are not used at all. Class C is used for Airspace above flight level 100 up to FL 660. Airspace is divided into lower airspace below FL 245 and upper airspace above FL 245.

Class A is not used.
Class B is not used.
Class C is used for controlled zones above and around airports and for airspace above FL 100 up to FL 660.
Class D is used for controlled zones, or above and around airspace Class C designated zones where CVFR is not necessary.
Class E is used for airspace between usually AGL and FL 100.
Class F is not used.
Class G is used below AGL. IFR flights in Class G are not allowed in Germany except for arrivals and departures in Radio Mandatory Zones around uncontrolled airfields with IFR procedures.
Iraq

In Iraq, the Flight Information Regions is known as Baghdad FIR. It is classified into Class A, D, E and G airspace. Class B, C and F airspace are not used in the Baghdad FIR. Air traffic services are provided in all controlled airspace, by the controlling ATC Unit, based on an ATS Surveillance System or MRU where authorized based on Procedural procedures and supplemented by ATC Surveillance System where possible.

Class A is established from FL235 – FL460 throughout the whole Baghdad FIR.
Class B is not used.
Class C is not used.
Class D is established in conjunction with airports that have operating control towers.
Class E is established at Baghdad, Basrah, Kirkuk, and Mosul TMAs. Class E airspace is also established along the air route structure.
Class F is not used.
Class G is established for all areas that are not classified as A, D or E. This airspace is primarily used by military VFR aircraft. A Common Traffic Advisory Frequency is established for aircraft self deconfliction.
Ireland

In Ireland, airspace is divided into classes A, C and G only.

Class A: This high-level en route controlled airspace is used predominately by commercial and passenger jets. Only IFR flights are permitted and they require ATC clearance. Class A airspace exists in the Northern Oceanic Transition Area and the Southern Oceanic Transition Area.
Class C: This is the controlled airspace above 7,500 feet and surrounding major airports. Both IFR and VFR flights are permitted and both require ATC clearance and separation service is to be provided by ATC.
Class G: This airspace is uncontrolled. Both IFR and VFR aircraft are permitted and neither requires an ATC clearance.
Italy
Class A is used for Rome and Milan TMAs
Class B is not used.
Class C is used in all airspace above FL 195, and in Military Control Zones above FL 195, to FL 460 excluded.
Class D is used for controlled zones and other TMAs.
Class E is used for airways from MEL to FL 115.
Class F is not used.
Class G is used in all other airspaces, and above FL460
Kenya

Classes A, C, D, G are used in Kenyan airspace, alongside unclassified military operation areas which are defined in Restricted Areas and Prohibited Areas, and are controlled by military air traffic control units.

Class A is used above FL145, except in areas where ground level exceeds FL145, in which case class A airspace exists above AGL and class G below.
Class C airspace is used exclusively in the Nairobi TMA and CTR.
Class D airspace is used in all other aerodrome airspaces.
Class G airspace exists everywhere else, particularly between ground level and AGL.
Lithuania

In Lithuania, Classes A and B are generally not used at all. Classes C and D are used in the following areas of controlled airspace of the Republic of Lithuania:

in control zones
in terminal control areas
in control area
in upper control area
Mauritius

Classes A, C and G are used in Mauritius.

Class A airspace exists within the entire Mauritius FIR, above FL245.
Class C airspace exists within 150 nautical miles of Mauritius, below FL245.
Class G airspace exists in all other areas of the Mauritius FIR.
Netherlands

In the Netherlands, a relatively large part of the country is Class A airspace. Near Amsterdam, the capital of the Netherlands, the airspace is almost completely built up with class A. It starts at 1500' MSL, and ends at FL195. Further away from Amsterdam and its airport Schiphol, Class A starts at a higher altitude. Class B is used a lot as well. Anywhere in the Netherlands, Class A airspace ends at FL195 and changes into Class C. Most of the CTRs are class D, some of them are class C. Class F is the only class that cannot be found in the Dutch airspace.

New Zealand

In New Zealand, Classes B, E and F are not used at all. Class A is used in Oceanic airspace above flight level 245 whereas Classes C and D are used in domestic airspace as part of the New Zealand FIR.

Class A is used at or above 24,500ft or FL245 in the Auckland Oceanic Flight Information Region.
Class B is not used.
Class C is used for control zones around major airports and associated surrounding control areas and en-route airspace in the New Zealand Flight Information Region.
Class D is used for control zones around regional airports and military airbases.
Class E is not used.
Class F is not used.
Class G is used for all other airspace.
Norway

In Norway, airspace is divided into classes A, C, D and G.

Class A is only used for Bodø OCA, FL195 and up.
Class C is used for controlled airspace.
Class D is used for controlled airspace where C is not used.
Class G is used elsewhere. G* is used in TIZ and TIA where two-way radio communication is required during opening hours.
Russia

adopted a modified version of ICAO airspace classification on November 1, 2010. The division into classes for the airspace of the Russian Federation was introduced for the first time in the history of Russia.
The airspace above the territory of the Russian Federation is divided as follows:

Class A applies to airspace above and including 8100 m. All operations in Class A airspace must follow IFR and are separated from each other by ATC. Permanent two-way radio contact with ATC is required. Permission for using airspace is required except for the special cases listed in clause 114 of the Federal rules for using Russian air space.
Class B is not used.
Class C airspace is defined below and allows IFR and VFR operations. Both IFR and VFR operations are required to have permanent two-way radio contact with ATC. IFR flights are separated from each other and from VFR flights. VFR flights are separated from IFR flights and are provided traffic information about other VFR flights. Permission for using airspace is required except for the special cases listed in clause 114 of the Federal rules for using Russian air space.
Class D is not used.
Class E is not used.
Class F is not used.
Class G airspace is defined wherever Class A and Class C airspaces are not defined. Class G airspace allows IFR and VFR operations. For altitudes less than the speed must not exceed. Flights are provided with flight information service as requested. IFR flights are required to have permanent two-way radio contact with ATC. No separation is provided by ATC. No permission for using airspace is required.

Airspace controlled by Russia outside the territory of Russia has different division into classes and includes redefined Class A and Class G, but no class C airspace.
Specific boundaries of airspaces are determined by the Order of the Ministry of Transport of the Russian Federation #199 of September 15, 2010.

Sweden

In Sweden, airspace is divided into airspace class C and G only with a small E class area stretching over the danish border into Swedish airspace.

Class C is used for all controlled airspace.
Class E is used for Area L3, a small area over the city of Malmö near the Swedish/Danish border. This area is controlled by ACC København.
Class G is used elsewhere.
United Kingdom

In addition the UK has a couple of special classes of airspace that do not fall within the ICAO classes:

Aerodrome traffic zones are circular zones around an airport with a radius of 2 nmi or 2.5 nmi depending on runway length, extending from the surface to AAL. Aircraft within an ATZ must obey the instructions of the tower controller, or must make radio contact with the Aerodrome Flight Information Service unit or Air/Ground Communication Service unit for the aerodrome before entering the zone, or must obey ground signals if non-radio.
Military air traffic zones are zones around military air bases in class G airspace. Military aircraft treat these as if they are controlled airspace; civilian traffic are advised but not obliged to do the same. A MATZ usually consists of a circular zone with a radius of 5 nm, extending from the surface to AAL. Stubs 4 nm wide and 5 nm in length, orientated with the aerodrome's main runway, extend on opposite sides of the central circle, extending from to AAL.
United States

The U.S. adopted a slightly modified version of the ICAO system on September 16, 1993, when regions of airspace designated according to older classifications were converted entirely. The exceptions are some terminal radar service areas, which have special rules and still exist in a few places.

With some exceptions, Class A airspace is applied to all airspace between and flight level 600. Above FL600, the airspace reverts to Class E. The transition altitude is also consistently everywhere. All operations in US Class A airspace must be conducted under IFR. SVFR flight in Class A airspace is prohibited.
Class B airspace is used to control the flow of traffic around major airports. The airspace is charted on a VFR sectional chart with a series of blue lines. Within these blue lines, the floor and the ceiling of the Class B airspace is defined. The lateral boundaries of Class B airspace are individually tailored to facilitate arriving and departing traffic operating under IFR. Class B airspace extends from the surface to generally MSL. In Denver, Colorado and Salt Lake City, Utah, the ceiling is at MSL, while in Phoenix, Arizona, the ceiling is at MSL. Charts must be consulted for the most current floor and ceiling information. Aircraft must establish two-way radio communication with ATC and obtain a clearance to enter Class B airspace. All aircraft operating inside or within 30 NM of the primary Class B airport are required to have a transponder with Mode C. The 30 NM Mode C Veil is denoted on VFR charts by a thin magenta line. VFR traffic must remain clear of clouds and maintain 3 SM of visibility while operating within Class B airspace.
Class C airspace is used around airports with a moderate traffic level.
Class D is used for smaller airports that have a control tower. The U.S. uses a modified version of the ICAO class C and D airspace, where only radio contact with ATC rather than an ATC clearance is required for VFR operations.
Other controlled airspace is designated as Class E, this includes a large part of the lower airspace. Class E airspace exists in many forms. It can serve as a surface-based extension to Class D airspace to accommodate IFR approach/departure procedure areas. Class E airspace can be designated to have a floor of 700' AGL or 1,200' AGL, or a customized floor of any other altitude. Class E airspace exists above Class G surface areas from 14,500' MSL to 18,000 MSL. Federal airways from 1,200 AGL to 18,000 MSL within of the centerline of the airway is designated Class E airspace. Airspace at any altitude over FL600 is designated Class E airspace.
The U.S. does not use ICAO Class F.
Class G airspace is mostly used for a small layer of airspace near the ground, but there are larger areas of Class G airspace in remote regions.
Airspace classes and VFR

Authorities use the ICAO definitions to derive additional rules for VFR cloud clearance, visibility, and equipment requirements.
For example, consider Class E airspace. It is possible that an aircraft operating under VFR is not in communication with ATC, so it is imperative that its pilot be able to see and avoid other aircraft. That includes IFR flights emerging from a cloud, so the VFR flight must keep a designated distance from the edges of clouds above, below, and laterally, and must maintain at least a designated visibility, to give the two aircraft time to observe and avoid each other. The low-level speed limit of 250 knots does not apply above, so the visibility requirements are higher.
On the other hand, in Class B and Class C airspaces, separation is provided by ATC to all aircraft. In these situations the VFR pilot only needs to see where his/her own aircraft is going, so visibility requirements are less stringent, and there is no designated minimum distance from clouds.
Similar considerations determine whether a VFR aircraft must use a two-way radio and/or a transponder.

Special use airspace

Each national authority designates areas of special use airspace, primarily for reasons of national security. This is not a separate classification from the ATC-based classes; each piece of SUA is contained in one or more zones of letter-classed airspace.
SUAs range in restrictiveness, from areas where flight is always prohibited except to authorized aircraft, to areas that are not charted but are used by military for potentially hazardous operations. Refer to the external links for more specific details.

Popular movies

The Hunger Games (film) - 2012 American dystopian action thriller science fiction-adventure film directed by Gary Ross and based on Suzanne Collins’s 2008 novel of the same name. It is the first insta...
untitled Captain Marvel sequel - part of Marvel Cinematic Universe....
Killers of the Flower Moon (film project) - Killers of the Flower Moon - film project in United States of America. It was presented as drama, detective fiction, thriller. The film project starred Leonardo Dicaprio, Robert De Niro. Director of...
Five Nights at Freddy's (film) - Five Nights at Freddy's - film published in 2017 in United States of America. Scenarist of the film - Scott Cawthon....

Popular books

Book of Revelation - The Book of Revelation is the final book of the New Testament, and consequently is also the final book of the Christian Bible. Its title is derived from the first word of the Koine Greek text: apok...
Book of Genesis - account of the creation of the world, the early history of humanity, Israel's ancestors and the origins...
Gospel of Matthew - The Gospel According to Matthew is the first book of the New Testament and one of the three synoptic gospels. It tells how Israel's Messiah, rejected and executed in Israel, pronounces judgement on ...
Michelin Guide - Michelin Guides are a series of guide books published by the French tyre company Michelin for more than a century. The term normally refers to the annually published Michelin Red Guide , the oldest...
Psalms - The Book of Psalms , commonly referred to simply as Psalms , the Psalter or "the Psalms", is the first book of the Ketuvim , the third section of the Hebrew Bible, and thus a book of th...
Ecclesiastes - Ecclesiastes is one of 24 books of the Tanakh , where it is classified as one of the Ketuvim . Originally written c. 450–200 BCE, it is also among the canonical Wisdom literature of the Old Tes...
The 48 Laws of Power - non-fiction book by American author Robert Greene. The book...

Popular television series

The Crown (TV series) - historical drama web television series about the reign of Queen Elizabeth II, created and principally written by Peter Morgan, and produced by Left Bank Pictures and Sony Pictures Tel...
Friends - American sitcom television series, created by David Crane and Marta Kauffman, which aired on NBC from September 22, 1994, to May 6, 2004, lasting ten seasons. With an ensemble cast sta...
Young Sheldon - spin-off prequel to The Big Bang Theory and begins with the character Sheldon...
Modern Family - American television mockumentary family sitcom created by Christopher Lloyd and Steven Levitan for the American Broadcasting Company. It ran for eleven seasons, from September 23...
Loki (TV series) - upcoming American web television miniseries created for Disney+ by Michael Waldron, based on the Marvel Comics character of the same name. It is set in the Marvel Cinematic Universe, shar...
Game of Thrones - American fantasy drama television series created by David Benioff and D. B. Weiss for HBO. It...
Shameless (American TV series) - American comedy-drama television series developed by John Wells which debuted on Showtime on January 9, 2011. It...

Airspace class

Abbreviations used in this article

ICAO definitions

ICAO adopted classifications

Use of airspace classes

Australia

Transition from GAAP to Class D

Canada

Denmark

Italy

Kenya

Russia

United Kingdom

United States

Airspace classes and VFR

Special use airspace