Anchor bolt


Anchor bolts are used to connect structural and non-structural elements to the concrete. The connection is made by an assembling of different components such as: anchor bolts, steel plates, stiffeners. Anchor bolts transfer different types of load: tension forces and shear forces.
A connection between structural elements can be represented by steel column attached to reinforced concrete foundation. Whereas, a common case of non-structural element attached to a structural one is represented by the connection between a facade system and a reinforced concrete wall.

Types

Cast-in-place

The simplest - and strongest - form of anchor bolt is cast-in-place, with its embedded end consisting of a standard hexagonal head bolt and washer, 90-bend, or some sort of forged or welded flange. The last are used in concrete-steel composite structures as shear connectors.
Other uses include anchoring machines to poured concrete floors and buildings to their concrete foundations.
Various typically disposable aids, mainly of plastic, are produced to secure and align cast-in-place anchors prior to concrete placement. Moreover, their position must also be coordinated with the reinforcement layout. Different types of cast-in-place anchors might be distinguished:
For all the type of the cast-in-place anchors, the load-transfer mechanisms is the mechanical interlock, i.e. the embedded part of the anchors in concrete transfers and the applied load via bearing pressure at the contact zone. At failure conditions, the level of bearing pressure can be higher than 10 times the concrete compressive strength, if a pure tension force is transferred.
Cast-in-place type anchors are also utilized in masonry applications, placed in wet mortar joints during the laying of brick and cast blocks.

Post-installed

Post-installed anchors can be installed in any position of hardened concrete after a drilling operation. A distinction is made according to their principle of operation.

Mechanical Expansion anchors

The force-transfer mechanism is based on friction mechanical interlock guaranteed by expansion forces. They can be furtherly divided into two categories:
The force-transfer mechanism is based on mechanical interlock. A special drilling operation allows to create a contact surface between the anchor head and the hole's wall where bearing stresses are exchanged.

Bonded anchors

The force-transfer mechanism is based on bond stresses provided by binding organic materials. Both Ribbed bars and threaded rods can be used and a change of the local bond mechanism can be appreciated experimentally. In ribbed bars the resistance is prevalently due to shear behavior of concrete between the ribs whereas for threaded rods friction prevails.. Bonded anchors are also referred as adhesive anchors or chemical anchors. The anchoring material is an adhesive usually consisting of epoxy, polyester, or vinylester resins. The performance of this anchor's types in terms of 'load-bearing capacity', especially under tension loads, is strictly related to the cleaning condition of the hole. Experimental results showed that the reduction of the capacity is up to 60%. The same applies also for moisture condition of concrete, for wet concrete the reduction is of 20% using polyester resin. Other issues are represented by high temperature behavior and creep response.

Screw anchors

The force-transfer mechanism of the screw anchor is based on concentrated pressure exchange between the screw and concrete through the pitches.

Plastic anchors

Tapcon screws

Tapcon screws are a popular anchor that stands for self tapping concrete screw. Larger diameter screws are referred to as LDT's. This type of fastener requires a pre-drilled hole—using a Tapcon drillbit—and are then screwed into the hole using a standard hex or phillips bit. These screws are often blue, white, or stainless. They are also available in versions for marine or high stress applications.

Plastic anchors

Their force-transfer mechanism is similar to mechanical expansion anchors. A torque moment is applied to a screw which is inserted in a plastic sleeve. As the torque is applied the plastic expands the sleeve against the sides of the hole acting as expansion force.

Powder-Actuated anchors

They act transferring the forces via mechanical interlock. This fastening technology is used in steel-to-steel connection, for instance to connect cold-formed profiles. A screw is inserted into the base material via a gas actuated gas gun. The driving energy is usually provided by firing a combustible propellant in powder form. The fastener's insertion provokes the plastic deformation of the base material which accommodates the fastener's head where the force transfer takes place.

Mechanical Behavior

Modes of Failure in tension

Anchors can fail in different way when loaded in tension:
In design verification under ultimate limit state, codes prescribe to verify all the possible failure mechanisms.

Modes of Failure in shear

Anchors can fail in different way when loaded in shear:
In design verification under ultimate limit state, codes prescribe to verify all the possible failure mechanisms.

Combined tension/shear

When contemporarily tension and shear load are applied to an anchor the failure occurs earlier with respect the un-coupled case. In current design codes a linear interaction domain is assumed.

Group of anchors

In order to increase the load-carrying capacity anchors are assembled in group, moreover this allow also to arrange a bending moment resisting connection. For tension and shear load, the mechanical behavior is markedly influenced by the spacing between the anchors and the possible difference in the applied forces.

Service load behavior

Under service loads anchor's displacement must be limited. The anchor performance under different loading condition is assessed experimentally, then an official document is produced by technical assessment body. In design phase, the displacement occurring under the characteristic actions should be not larger than the admissible displacement reported in the technical document.

Seismic load behavior

Under seismic loads and there would be the possibility that an anchor is contemporarily installed in a crack and subjected to inertia loads proportional both to the mass and the acceleration of the attached element to the base material. The load conditions in this case can be summarized as follow:
Exceptional loads differ from ordinary static loads for their rise time. High displacement rates are involved in impact loading. Regarding steel to concrete connections, some examples consist in collision of vehicle on barriers connected to concrete base and explosions. Apart from these extraordinary loads, structural connections are subjected to seismic actions, which rigorously have to be treated via dynamic approach. For instance, seismic pull-out action on anchor can have 0.03 seconds of rise time. On the contrary, in a quasi-static test, 100 second may be assumed as time interval to reach the peak load. Regarding the concrete base failure mode: Concrete cone failure loads increase with elevated loading rates with respect the static one.

Designs