Angular unit


Throughout history, angles have been measured in many different units. The most contemporary units are the degree and radian, but many others have been used throughout history. The purpose of this page is to aggregate other concepts pertaining to the angular unit, where additional explanation can be provided.

Angle measurement in general

The size of a geometric angle is usually characterized by the magnitude of the smallest rotation that maps one of the rays into the other. Angles that have the same size are said to be equal or congruent or equal in measure.
In some contexts, such as identifying a point on a circle or describing the orientation of an object in two dimensions relative to a reference orientation, angles that differ by an exact multiple of a full turn are effectively equivalent. In other contexts, such as identifying a point on a spiral curve or describing the cumulative rotation of an object in two dimensions relative to a reference orientation, angles that differ by a non-zero multiple of a full turn are not equivalent.
In order to measure an angle θ, a circular arc centered at the vertex of the angle is drawn, e.g. with a pair of compasses. The ratio of the length s of the arc by the radius r of the circle is the measure of the angle in radians.
The measure of the angle in another angular unit is then obtained by multiplying its measure in radians by the scaling factor, where k is the measure of a complete turn in the chosen unit :
The value of θ thus defined is independent of the size of the circle: if the length of the radius is changed then the arc length changes in the same proportion, so the ratio s/r is unaltered.

Angle addition postulate

The angle addition postulate states that if B is in the interior of angle AOC, then
The measure of the angle AOC is the sum of the measure of angle AOB and the measure of angle BOC.
In this postulate it does not matter in which unit the angle is measured as long as each angle is measured in the same unit.

Units

One radian is the angle subtended by an arc of a circle that has the same length as the circle's radius. The radian is the derived quantity of angular measurement in the SI system. By definition, it is dimensionless, though it may be specified as rad to avoid ambiguity. Angles measured in degrees, are shown with the symbol °. Subdivisions of the degree are minute and second. An angle of 360° corresponds to the angle subtended by a full circle, and is equal to 2π radians, or 400 gradians.
Other units used to represent angles are listed in the following table. These units are defined such that the number of turns is equivalent to a full circle.

Equivalent time descriptors

In astronomy, right ascension and declination are usually measured in angular units, expressed in terms of time, based on a 24 hr day.
UnitSymbolDegreeRadiansCircleOther
Hourh15°
Minutem0°15' hour
Seconds0°0'15" minute

Other descriptors

Although the definition of the measurement of an angle does not support the concept of a negative angle, it is frequently useful to impose a convention that allows positive and negative angular values to represent orientations and/or rotations in opposite directions relative to some reference.
In a two-dimensional Cartesian coordinate system, an angle is typically defined by its two sides, with its vertex at the origin. The initial side is on the positive x-axis, while the other side or terminal side is defined by the measure from the initial side in radians, degrees, or turns. With positive angles representing rotations toward the positive y-axis and negative angles representing rotations toward the negative y-axis. When Cartesian coordinates are represented by standard position, defined by the x-axis rightward and the y-axis upward, positive rotations are anticlockwise and negative rotations are clockwise.
In many contexts, an angle of −θ is effectively equivalent to an angle of "one full turn minus θ". For example, an orientation represented as −45° is effectively equivalent to an orientation represented as 360° − 45° or 315°. However, a rotation of −45° would not be the same as a rotation of 315°.
In three-dimensional geometry, "clockwise" and "anticlockwise" have no absolute meaning, so the direction of positive and negative angles must be defined relative to some reference, which is typically a vector passing through the angle's vertex and perpendicular to the plane in which the rays of the angle lie.
In navigation, bearings are measured relative to north. By convention, viewed from above, bearing angle are positive clockwise, so a bearing of 45° corresponds to a north-east orientation. Negative bearings are not used in navigation, so a north-west orientation corresponds to a bearing of 315°.

Alternative ways of measuring the size of an angle

There are several alternatives to measuring the size of an angle by the corresponding angle of rotation.
The grade of a slope, or gradient is equal to the tangent of the angle, or sometimes the sine. Gradients are often expressed as a percentage. For very small values, the grade of a slope is approximately the measure of an angle in radians.
In rational geometry the spread between two lines is defined at the square of sine of the angle between the lines. Since the sine of an angle and the sine of its supplementary angle are the same any angle of rotation that maps one of the lines into the other leads to the same value of the spread between the lines.

Astronomical approximations

Astronomers measure angular separation of objects in degrees from their point of observation.
These measurements clearly depend on the individual subject, and the above should be treated as rough rule of thumb approximations only.

Measurements that are not angular units

Not all angle measurements are angular units, for an angular measurement it is definitional that the angle addition postulate holds.
Some angle measurements where the angle addition postulate does not holds.