Automobile handling
Automobile handling and vehicle handling are descriptions of the way a wheeled vehicle responds and reacts to the inputs of a driver, as well as how it moves along a track or road. It is commonly judged by how a vehicle performs particularly during cornering, acceleration, and braking as well as on the vehicle's directional stability when moving in steady state condition.
In the automotive industry, handling and braking are the major components of a vehicle's "active" safety, as well as its ability to perform in Auto Racing. The maximum lateral acceleration is sometimes discussed separately as "road holding".. Automobiles driven on public roads whose engineering requirements emphasize handling over comfort and passenger space are named sports cars.
Factors that affect a car's handling
Weight distribution
Centre of mass height
The centre of mass height, also known as the centre of gravity height, or CGZ, relative to the track, determines load transfer from side to side and causes body lean. When tires of a vehicle provide a centripetal force to pull it around a turn, the momentum of the vehicle actuates load transfer in a direction going from the vehicle's current position to a point on a path tangent to the vehicle's path. This load transfer presents itself in the form of body lean. In extreme circumstances, the vehicle may roll over.Height of the centre of mass relative to the wheelbase determines load transfer between front and rear. The car's momentum acts at its centre of mass to tilt the car forward or backward, respectively during braking and acceleration. Since it is only the downward force that changes and not the location of the centre of mass, the effect on over/under steer is opposite to that of an actual change in the centre of mass. When a car is braking, the downward load on the front tires increases and that on the rear decreases, with corresponding change in their ability to take sideways load.
A lower centre of mass is a principal performance advantage of sports cars, compared to sedans and SUVs. Some cars have body panels made of lightweight materials partly for this reason.
Body lean can also be controlled by the springs, anti-roll bars or the roll center heights.
| Model | Model year | CoG height |
| Dodge Ram B-150 | 1987 | |
| Chevrolet Tahoe | 1998 | |
| Lotus Elise | 2000 | |
| Tesla Model S | 2014 | |
| Chevrolet Corvette Z51 | 2014 | |
| Alfa Romeo 4C | 2013 | |
| Formula 1 Car | 2017 | 25 centimetres |
Centre of mass
In steady-state cornering, front-heavy cars tend to understeer and rear-heavy cars to oversteer, all other things being equal. The mid-engine design seeks to achieve the ideal center of mass, though front-engine design has the advantage of permitting a more practical engine-passenger-baggage layout. All other parameters being equal, at the hands of an expert driver a neutrally balanced mid-engine car can corner faster, but a FR layout car is easier to drive at the limit.The rearward weight bias preferred by sports and racing cars results from handling effects during the transition from straight-ahead to cornering. During corner entry the front tires, in addition to generating part of the lateral force required to accelerate the car's centre of mass into the turn, also generate a torque about the car's vertical axis that starts the car rotating into the turn. However, the lateral force being generated by the rear tires is acting in the opposite torsional sense, trying to rotate the car out of the turn. For this reason, a car with "50/50" weight distribution will understeer on initial corner entry. To avoid this problem, sports and racing cars often have a more rearward weight distribution. In the case of pure racing cars, this is typically between "40/60" and "35/65". This gives the front tires an advantage in overcoming the car's moment of inertia, thus reducing corner-entry understeer.
Using wheels and tires of different sizes is a lever automakers can use to fine tune the resulting over/understeer characteristics.
Roll angular inertia
This increases the time it takes to settle down and follow the steering. It depends on the height and width, and can be approximately calculated by the equation: .Greater width, then, though it counteracts center of gravity height, hurts handling by increasing angular inertia. Some high performance cars have light materials in their fenders and roofs partly for this reason
Yaw and pitch angular inertia (polar moment)
Unless the vehicle is very short, compared to its height or width, these are about equal. Angular inertia determines the rotational inertia of an object for a given rate of rotation.The yaw angular inertia tends to keep the direction the car is pointing changing at a constant rate. This makes it slower to swerve or go into a tight curve, and it also makes it slower to turn straight again.
The pitch angular inertia detracts from the ability of the suspension to keep front and back tire loadings constant on uneven surfaces and therefore contributes to bump steer.
Angular inertia is an integral over the square of the distance from the center of gravity, so it favors small cars even though the lever arms also increase with scale.
Mass near the ends of a car can be avoided, without re-designing it to be shorter, by the use of light materials for bumpers and fenders or by deleting them entirely. If most of the weight is in the middle of the car then the vehicle will be easier to spin, and therefore will react quicker to a turn.
Suspension
Automobile suspensions have many variable characteristics, which are generally different in the front and rear and all of which affect handling. Some of these are: spring rate, damping, straight ahead camber angle, camber change with wheel travel, roll center height and the flexibility and vibration modes of the suspension elements. Suspension also affects unsprung weight.Many cars have suspension that connects the wheels on the two sides, either by a sway bar and/or by a solid axle. The Citroën 2CV has interaction between the front and rear suspension.
The flexing of the frame interacts with the suspension.
Spring rate
The following types of springs are commonly used for automobile suspension, variable rate springs and linear rate springs. When a load is applied to a linear rate spring the spring compresses an amount directly proportional to the load applied. This type of spring is commonly used in road racing applications when ride quality is not a concern. A linear spring will behave the same at all times. This provides predictable handling characteristics during high speed cornering, acceleration and braking. Variable springs have low initial springs rates. The spring rate gradually increases as it is compressed. In simple terms the spring becomes stiffer as it is compressed. The ends of the spring are wound tighter to produce a lower spring rate. When driving this cushions small road imperfections improving ride quality. However once the spring is compressed to a certain point the spring is not wound as tight providing a higher spring rate. This prevents excessive suspension compression and prevents dangerous body roll, which could lead to a roll over. Variable rate springs are used in cars designed for comfort as well as off-road racing vehicles. In off-road racing they allow a vehicle to absorb the violent shock from a jump effectively as well as absorb small bumps along the off-road terrain effectively.Suspension travel
The severe handling vice of the TR3B and related cars was caused by running out of suspension travel.Other vehicles will run out of suspension travel with some combination of bumps and turns, with similarly catastrophic effect. Excessively modified cars also may encounter this problem.
Tires and wheels
In general, softer rubber, higher hysteresis rubber and stiffer cord configurations increase road holding and improve handling. On most types of poor surfaces, large diameter wheels perform better than lower wider wheels. The depth of tread remaining greatly affects aquaplaning. Increasing tire pressures reduces their slip angle, but lessening the contact area is detrimental in usual surface conditions and should be used with caution.The amount a tire meets the road is an equation between the weight of the car and the type of its tire. A 1000 kg car can depress a 185/65/15 tire more than a 215/45/15 tire longitudinally thus having better linear grip and better braking distance not to mention better aquaplaning performance, while the wider tires have better cornering resistance.
The contemporary chemical make-up of tires is dependent of the ambient and road temperatures. Ideally a tire should be soft enough to conform to the road surface, but be hard enough to last for enough duration to be economically feasible. It is usually a good idea having different set of summer and winter tires for climates having these temperatures.
Track and wheelbase
The axle track provides the resistance to lateral weight transfer and body lean. The wheelbase provides resistance to longitudinal weight transfer and to pitch angular inertia, and provides the torque lever arm to rotate the car when swerving. The wheelbase, however, is less important than angular inertia to the vehicle's ability to swerve quickly.The wheelbase contributes to the vehicle's turning radius, which is also a handling characteristic.
Unsprung weight
Ignoring the flexing of other components, a car can be modeled as the sprung weight, carried by the springs, carried by the unsprung weight, carried by the tires, carried by the road. Unsprung weight is more properly regarded as a mass which has its own inherent inertia separate from the rest of the vehicle. When a wheel is pushed upwards by a bump in the road, the inertia of the wheel will cause it to be carried further upward above the height of the bump. If the force of the push is sufficiently large, the inertia of the wheel will cause the tire to completely lift off the road surface resulting in a loss of traction and control. Similarly when crossing into a sudden ground depression, the inertia of the wheel slows the rate at which it descends. If the wheel inertia is large enough, the wheel may be temporarily separated from the road surface before it has descended back into contact with the road surface.This unsprung weight is cushioned from uneven road surfaces only by the compressive resilience of the tire, which aids the wheel in remaining in contact with the road surface when the wheel inertia prevents close-following of the ground surface. However, the compressive resilience of the tire results in rolling resistance which requires additional kinetic energy to overcome, and the rolling resistance is expended in the tire as heat due to the flexing of the rubber and steel bands in the sidewalls of the tires. To reduce rolling resistance for improved fuel economy and to avoid overheating and failure of tires at high speed, tires are designed to have limited internal damping.
So the "wheel bounce" due to wheel inertia, or resonant motion of the unsprung weight moving up and down on the springiness of the tire, is only poorly damped, mainly by the dampers or shock absorbers of the suspension. For these reasons, high unsprung weight reduces road holding and increases unpredictable changes in direction on rough surfaces.
This unsprung weight includes the wheels and tires, usually the brakes, plus some percentage of the suspension, depending on how much of the suspension moves with the body and how much with the wheels; for instance a solid axle suspension is completely unsprung. The main factors that improve unsprung weight are a sprung differential and inboard brakes. Wheel materials and sizes will also have an effect. Aluminium alloy wheels are common due to their weight characteristics which help to reduce unsprung mass. Magnesium alloy wheels are even lighter but corrode easily.
Since only the brakes on the driving wheels can easily be inboard, the Citroën 2CV had inertial dampers on its rear wheel hubs to damp only wheel bounce.
Aerodynamics
forces are generally proportional to the square of the air speed, therefore car aerodynamics become rapidly more important as speed increases. Like darts, aeroplanes, etc., cars can be stabilised by fins and other rear aerodynamic devices. However, in addition to this cars also use downforce or "negative lift" to improve road holding. This is prominent on many types of racing cars, but is also used on most passenger cars to some degree, if only to counteract the tendency for the car to otherwise produce positive lift.In addition to providing increased adhesion, car aerodynamics are frequently designed to compensate for the inherent increase in oversteer as cornering speed increases. When a car corners, it must rotate about its vertical axis as well as translate its center of mass in an arc. However, in a tight-radius corner the angular velocity of the car is high, while in a longer-radius corner the angular velocity is much lower. Therefore, the front tires have a more difficult time overcoming the car's moment of inertia during corner entry at low speed, and much less difficulty as the cornering speed increases. So the natural tendency of any car is to understeer on entry to low-speed corners and oversteer on entry to high-speed corners. To compensate for this unavoidable effect, car designers often bias the car's handling toward less corner-entry understeer, and add rearward bias to the aerodynamic downforce to compensate in higher-speed corners. The rearward aerodynamic bias may be achieved by an airfoil or "spoiler" mounted near the rear of the car, but a useful effect can also be achieved by careful shaping of the body as a whole, particularly the aft areas.
In recent years, aerodynamics have become an area of increasing focus by racing teams as well as car manufacturers. Advanced tools such as wind tunnels and computational fluid dynamics have allowed engineers to optimize the handling characteristics of vehicles. Advanced wind tunnels such as Wind Shear's Full Scale, Rolling Road, Automotive Wind Tunnel recently built in Concord, North Carolina have taken the simulation of on-road conditions to the ultimate level of accuracy and repeatability under very controlled conditions. CFD has similarly been used as a tool to simulate aerodynamic conditions but through the use of extremely advanced computers and software to duplicate the car's design digitally then "test" that design on the computer.
Delivery of power to the wheels and brakes
The coefficient of friction of rubber on the road limits the magnitude of the vector sum of the transverse and longitudinal force. So the driven wheels or those supplying the most braking tend to slip sideways. This phenomenon is often explained by use of the circle of forces model.One reason that sports cars are usually rear wheel drive is that power induced oversteer is useful, to a skilled driver, for tight curves. The weight transfer under acceleration has the opposite effect and either may dominate, depending on the conditions. Inducing oversteer by applying power in a front wheel drive car is possible via proper use of "Left-foot braking." In any case, this is not an important safety issue, because power is not normally used in emergency situations. Using low gears down steep hills may cause some oversteer.
The effect of braking on handling is complicated by load transfer, which is proportional to the acceleration times the ratio of the center of gravity height to the wheelbase. The difficulty is that the acceleration at the limit of adhesion depends on the road surface, so with the same ratio of front to back braking force, a car will understeer under braking on slick surfaces and oversteer under hard braking on solid surfaces. Most modern cars combat this by varying the distribution of braking in some way. This is important with a high center of gravity, but it is also done on low center of gravity cars, from which a higher level of performance is expected.
Steering
Depending on the driver, steering force and transmission of road forces back to the steering wheel and the steering ratio of turns of the steering wheel to turns of the road wheels affect control and awareness. Play—free rotation of the steering wheel before the wheels rotate—is a common problem, especially in older model and worn cars. Another is friction. Rack and pinion steering is generally considered the best type of mechanism for control effectiveness. The linkage also contributes play and friction. Caster—offset of the steering axis from the contact patch—provides some of the self-centering tendency.Precision of the steering is particularly important on ice or hard packed snow where the slip angle at the limit of adhesion is smaller than on dry roads.
The steering effort depends on the downward force on the steering tires and on the radius of the contact patch. So for constant tire pressure, it goes like the 1.5 power of the vehicle's weight. The driver's ability to exert torque on the wheel scales similarly with his size. The wheels must be rotated farther on a longer car to turn with a given radius. Power steering reduces the required force at the expense of feel. It is useful, mostly in parking, when the weight of a front-heavy vehicle exceeds about ten or fifteen times the driver's weight, for physically impaired drivers and when there is much friction in the steering mechanism.
Four-wheel steering has begun to be used on road cars. It relieves the effect of angular inertia by starting the whole car moving before it rotates toward the desired direction. It can also be used, in the other direction, to reduce the turning radius. Some cars will do one or the other, depending on the speed.
Steering geometry changes due to bumps in the road may cause the front wheels to steer in different directions together or independent of each other. The steering linkage should be designed to minimize this effect.
Electronic stability control
Electronic stability control is a computerized technology that improves the safety of a vehicle's stability by attempting to detect and prevent skids. When ESC detects loss of steering control, the system applies individual brakes to help "steer" the vehicle where the driver wants to go. Braking is automatically applied to individual wheels, such as the outer front wheel to counter oversteer, or the inner rear wheel to counter understeer.The stability control of some cars may not be compatible with some driving techniques, such as power induced over-steer. It is therefore, at least from a sporting point of view, preferable that it can be disabled.
Static alignment of the wheels
Of course things should be the same, left and right, for road cars. Camber affects steering because a tire generates a force towards the side that the top is leaning towards. This is called camber thrust. Additional front negative camber is used to improve the cornering ability of cars with insufficient camber gain.Rigidity of the frame
The frame may flex with load, especially twisting on bumps.Rigidity is considered to help handling. At least it simplifies the suspension engineers work.
Some cars, such as the Mercedes-Benz 300SL have had high doors to allow a stiffer frame.
Driver handling the car
Handling is a property of the car, but different characteristics will work well with different drivers.Familiarity
The more experience a person has with a car or type of car the more likely they will be to take full advantage of its handling characteristics under adverse conditions.Position and support for the driver
Having to withstand "g forces" in his/her arms interferes with a driver's precise steering. In a similar manner, a lack of support for the seating position of the driver may cause them to move around as the car undergoes rapid acceleration. This interferes with precise control inputs, making the car more difficult to control.Being able to reach the controls easily is also an important consideration, especially if a car is being driven hard.
In some circumstances, good support may allow a driver to retain some control, even after a minor accident or after the first stage of an accident.
External conditions that affect handling
Weather
Weather affects handling by changing the amount of available traction on a surface. Different tires do best in different weather. Deep water is an exception to the rule that wider tires improve road holding.Road condition
Cars with relatively soft suspension and with low unsprung weight are least affected by uneven surfaces, while on flat smooth surfaces the stiffer the better. Unexpected water, ice, oil, etc. are hazards.Common handling problems
When any wheel leaves contact with the road there is a change in handling, so the suspension should keep all four wheels on the road in spite of hard cornering, swerving and bumps in the road. It is very important for handling, as well as other reasons, not to run out of suspension travel and "bottom" or "top".It is usually most desirable to have the car adjusted for a small amount of understeer, so that it responds predictably to a turn of the steering wheel and the rear wheels have a smaller slip angle than the front wheels. However this may not be achievable for all loading, road and weather conditions, speed ranges, or while turning under acceleration or braking. Ideally, a car should carry passengers and baggage near its center of gravity and have similar tire loading, camber angle and roll stiffness in front and back to minimise the variation in handling characteristics. A driver can learn to deal with excessive oversteer or understeer, but not if it varies greatly in a short period of time.
The most important common handling failings are;
- Understeer – the front wheels tend to crawl slightly or even slip and drift towards the outside of the turn. The driver can compensate by turning a little more tightly, but road-holding is reduced, the car's behaviour is less predictable and the tires are liable to wear more quickly.
- Oversteer – the rear wheels tend to crawl or slip towards the outside of the turn more than the front. The driver must correct by steering away from the corner, otherwise the car is liable to spin, if pushed to its limit. Oversteer is sometimes useful, to assist in steering, especially if it occurs only when the driver chooses it by applying power.
- Bump steer – the effect of irregularity of a road surface on the angle or motion of a car. It may be the result of the kinematic motion of the suspension rising or falling, causing toe-in or toe-out at the loaded wheel, ultimately affecting the yaw angle of the car. It may also be caused by defective or worn out suspension components. This will always happen under some conditions but depends on suspension, steering linkage, unsprung weight, angular inertia, differential type, frame rigidity, tires and tire pressures. If suspension travel is exhausted the wheel either bottoms or loses contact with the road. As with hard turning on flat roads, it is better if the wheel picks up by the spring reaching its neutral shape, rather than by suddenly contacting a limiting structure of the suspension.
- Body roll – the car leans towards the outside of the curve. This interferes with the driver's control, because they must wait for the car to finish leaning before they can fully judge the effect of his steering change. It also adds to the delay before the car moves in the desired direction. It also slightly changes the weight borne by the tires as described in weight transfer.
- Excessive load transfer – On any vehicle that is cornering, the outside wheels are more heavily loaded than the inside due to the CG being above the ground. Total weight transfer, in steady cornering, is determined by the ratio of the height of a car's center of gravity to its axle track. When the weight transfer equals half the vehicle's loaded weight, it will start to roll over. This can be avoided by manually or automatically reducing the turn rate, but this causes further reduction in road-holding.
- Slow response – sideways acceleration does not start immediately when the steering is turned and may not stop immediately when it is returned to center. This is partly caused by body roll. Other causes include tires with high slip angle, and yaw and roll angular inertia. Roll angular inertia aggravates body roll by delaying it. Soft tires aggravate yaw angular inertia by waiting for the car to reach their slip angle before turning the car.
Compromises
High levels of comfort are difficult to reconcile with a low center of gravity, body roll resistance, low angular inertia, support for the driver, steering feel and other characteristics that make a car handle well.
For ordinary production cars, manufactures err towards deliberate understeer as this is safer for inexperienced or inattentive drivers than is oversteer. Other compromises involve comfort and utility, such as preference for a softer smoother ride or more seating capacity.
Inboard brakes improve both handling and comfort but take up space and are harder to cool. Large engines tend to make cars front or rear heavy. Fuel economy, staying cool at high speeds, ride comfort and long wear all tend to conflict with road holding, while wet, dry, deep water and snow road holding are not exactly compatible. A-arm or wishbone front suspension tends to give better handling, because it provides the engineers more freedom to choose the geometry, and more road holding, because the camber is better suited to radial tires, than MacPherson strut, but it takes more space.
The older Live axle rear suspension technology, familiar from the Ford Model T, is still widely used in most sport utility vehicles and trucks, often for the purposes of durability. The live axle suspension is still used in some sports cars, like the Ford Mustang, and is better for drag racing, but generally has problems with grip on bumpy corners, fast corners and stability at high speeds on bumpy straights.
Aftermarket modifications and adjustments
Lowering the center of gravity will always help the handling. This can be done to some extent by using plastic windows and light roof, hood and trunk lid materials, by reducing the ground clearance, etc. Increasing the track with "reversed" wheels will have a similar effect, but the wider the car the less spare room it has on the road and the farther it may have to swerve to miss an obstacle.Stiffer springs and/or shocks, both front and rear, will generally improve handling on close to perfect surfaces, while worsening handling on less-than-perfect road conditions by "skipping" the car, thus making handling the vehicle difficult. Aftermarket performance suspension kits are usually readily available.
Lighter wheels improve handling as well as ride comfort, by lessening unsprung weight.
Moment of inertia can be reduced by using lighter bumpers and wings, or none at all.
Fixing understeer or oversteer conditions is achieved by either an increase or decrease in grip on the front or rear axles. If the front axle has more grip than a similar vehicle with neutral steer characteristics, the vehicle will oversteer. The oversteering vehicle may be "tuned" by hopefully increasing rear axle grip, or alternatively by reducing front axle grip. The opposite is true for an understeering vehicle.
The following actions will have the tendency to "increase the grip" of an axle. Increasing moment arm distance to cg, reducing lateral load transfer, increasing tire contact patch size, increasing the longitudinal load transfer to that axle, and decreasing tire pressure.
Cars with unusual handling problems
Certain vehicles can be involved in a disproportionate share of single-vehicle accidents; their handling characteristics may play a role:- Early Porsche 911s – suffered from treacherous lift off oversteer ; also the inside front wheel leaves the road during hard cornering on dry pavement, causing increasing understeer. The roll bar stiffness at the front is set to compensate for the rear-heaviness and gives neutral handling in ordinary driving. This compensation starts to give out when the wheel lifts. A skilled driver can use the 911's other features to his/her advantage, making the 911 an extremely capable sports car in expert hands. Later 911s have had increasingly sophisticated rear suspensions and larger rear tires, eliminating these problems.
- Triumph TR2, and TR3 – began to oversteer more suddenly when their inside rear wheel lifted.
- Volkswagen Beetle – senstitivity to crosswinds, due to the lightness of the front of the rear engine car; and poor roll stability due to the swing axle suspension. People who drove them hard fitted reversed wheels and bigger rear tires and rims to ameliorate.
- Chevrolet Corvair - poor roll stability due to the swing axle rear suspension similar to that used in the Volkswagen Beetle, and cited for dangerous handling in Ralph Nader's book Unsafe at Any Speed. These problems were corrected with the redesign of the Corvair for 1965, but sales did not recover from the negative publicity and it was discontinued.
- The large, rear-engine Tatra 87 killed so many Nazi officers during World War II that the German Army eventually forbade its officers from driving the Tatra.
- Some 1950s American "full size" cars responded very slowly to steering changes because of their very large angular inertia, softly tuned suspension which made ride quality a priority over cornering, and comfort oriented cross bias tires. Auto Motor und Sport reported on one of these that they lacked the courage to test it for top speed, probably due to their familiarity with smaller European cars and their unfamiliarity with large American cars.
- Dodge Omni and Plymouth Horizon – these early American responses to the Volkswagen Rabbit were found "unacceptable" in their initial testing by Consumer Reports, due to an observed tendency to display an uncontrollable oscillating yaw from side to side under certain steering inputs. While Chrysler's denials of this behaviour were countered by a persistent trickle of independent reports of this behaviour, production of the cars was altered to equip them with both a lighter weight steering wheel and a steering damper, and no further reports of this problem were heard.
- The Suzuki Samurai – was similarly reported by Consumer Reports to exhibit a propensity to tipping over onto two wheels, to the point where Consumer Reports claimed they were afraid to continue testing the vehicle without the attachment of outrigger wheels to catch it from completely rolling over. In its first set of tests, the Samurai performed well. R. David Little, Consumers Union's technical director, drove the light SUV through several short, hard turns, designed to simulate an emergency, such as trying to avoid a child running in front of the car. An article published several years later in a Consumer Reports anniversary issue prompted Suzuki to sue. The suit was based on the perception that Consumer Reports rigged the results: "This case is about lying and cheating by Consumers Union for its own financial motives," George F. Ball, Suzuki's managing counsel, said Monday. "They were in debt , and they needed a blockbuster story to raise and solicit funds." Entrepreneur Magazine reported that "Suzuki's case centered on a change CU made while testing the vehicle. After the Samurai and other SUVs completed the standard course without threatening to roll over, CU altered the course to make the turns more abrupt. The other vehicles didn't show a problem, but the Samurai tipped up and would have rolled over but for outriggers set up to prevent that outcome" After eight years in court the parties consented to a settlement which did not include monetary damages nor a retraction. Commenting on the settlement, Consumer Union said,"Consumers Union also says in the agreement that it "never intended to imply that the Samurai easily rolls over in routine driving conditions." CU Vice President of Technical Policy further stated: "There is no apology. "We stand fully behind our testing and rating of the Samurai." In a joint press statement Suzuki recognized "CU's stated commitment for objective and unbiased testing and reporting."
- Mercedes-Benz A-Class – a tall car with a high center of gravity; early models showed excessive body roll during sharp swerving manoeuvres and rolled over, most particularly during the Swedish moose test. This was later corrected using Electronic Stability Control and retrofitted at great expense to earlier cars.
- Ford Explorer – a dangerous tendency to blow a rear tire and flip over. Ford had constructed a vehicle with a high center of gravity; between 68 and 74 cm above ground. The tendency to roll over on sharp changes in direction is built into the vehicle. Ford attempted to counteract the forces of nature by specifying lower than optimum pressures in the tires in order to induce them to lose traction and slide under sideways forces rather than to grip and force the vehicle to roll over. For reasons that were never entirely clear, tires from one factory tended to blow out when under inflated, these vehicles then rolled over, which led to a spate of well publicized single-vehicle accidents.
- The Jensen GT – was introduced in attempt to broaden the sales base of the Jensen Healey, which had up to that time been a roadster or convertible. Its road test report in Motor Magazine and a very similar one, soon after, in Road & Track concluded that it was no longer fun enough to drive to be worth that much money. They blamed it on minor suspension changes. Much more likely, the change in weight distribution was at fault. The Jensen Healey was a rather low and wide fairly expensive sports car, but the specifications of its suspension were not particularly impressive, having a solid rear axle. Unlike the AC Ace, with its double transverse leaf rear suspension and aluminium body, the Jensen Healey could not stand the weight of that high up metal and glass and still earn a premium price for its handling. The changes also included a cast iron exhaust manifold replacing the aluminium one, probably to partly balance the high and far back weight of the top. The factory building was used to build multi-tub truck frames.
- The rear engined Renault Dauphine earned in Spain the sobriquet of the "widow's car", due to its bad handling.
- Three-wheeled cars/vehicles have unique handling issues, especially considering whether the single wheel is at the front or back. Buckminster Fuller's Dymaxion car caused a sensation, but ignorance of the problems of rear-wheel-steering led to a fatal crash that destroyed its reputation.