Capstan equation


The capstan equation or belt friction equation, also known as Eytelwein's formula, relates the hold-force to the load-force if a flexible line is wound around a cylinder.
Because of the interaction of frictional forces and tension, the tension on a line wrapped around a capstan may be different on either side of the capstan. A small holding force exerted on one side can carry a much larger loading force on the other side; this is the principle by which a capstan-type device operates.
A holding capstan is a ratchet device that can turn only in one direction; once a load is pulled into place in that direction, it can be held with a much smaller force. A powered capstan, also called a winch, rotates so that the applied tension is multiplied by the friction between rope and capstan. On a tall ship a holding capstan and a powered capstan are used in tandem so that a small force can be used to raise a heavy sail and then the rope can be easily removed from the powered capstan and tied off.
In rock climbing with so-called top-roping, a lighter person can hold a heavier person due to this effect.
The formula is
where is the applied tension on the line, is the resulting force exerted at the other side of the capstan, is the coefficient of friction between the rope and capstan materials, and is the total angle swept by all turns of the rope, measured in radians.
Several assumptions must be true for the formula to be valid:
  1. The rope is on the verge of full sliding, i.e. is the maximum load that one can hold. Smaller loads can be held as well, resulting in a smaller effective contact angle.
  2. It is important that the line is not rigid, in which case significant force would be lost in the bending of the line tightly around the cylinder. For instance a Bowden cable is to some extent rigid and doesn't obey the principles of the Capstan equation.
  3. The line is non-elastic.
It can be observed that the force gain increases exponentially with the coefficient of friction, the number of turns around the cylinder, and the angle of contact. Note that the radius of the cylinder has no influence on the force gain.
The table below lists values of the factor based on the number of turns and coefficient of friction μ.
From the table it is evident why one seldom sees a sheet wound more than three turns around a winch. The force gain would be extreme besides being counter-productive since there is risk of a riding turn, result being that the sheet will foul, form a knot and not run out when eased.
It is both ancient and modern practice for anchor capstans and jib winches to be slightly flared out at the base, rather than cylindrical, to prevent the rope from sliding down. The rope wound several times around the winch can slip upwards gradually, with little risk of a riding turn, provided it is tailed, by hand or a self-tailer.
For instance, the factor "153,552,935" means, in theory, that a newborn baby would be capable of holding the weight of two supercarriers. The large number of turns around the capstan combined with such a high friction coefficient mean that very little additional force is necessary to hold such heavy weight in place. The cables necessary to support this weight, as well as the capstan's ability to withstand the crushing force of those cables, are separate considerations.

Generalization of the capstan equation for a V-belt

The belt friction equation for a v-belt is:
where is the angle between the two flat sides of the pulley that the v-belt presses against. A flat belt has an effective angle of.
The material of a V-belt or multi-V serpentine belt tends to wedge into the mating groove in a pulley as the load increases, improving torque transmission.
For the same power transmission, a V-belt requires less tension than a flat belt, increasing bearing life.

Generalization of the capstan equation for a rope lying on an arbitrary orthotropic surface

If a rope is lying in equilibrium under tangential forces on a rough orthotropic surface then all three following conditions are satisfied:
  1. No separation – normal reaction is positive for all points of the rope curve:
  2. :, where is a normal curvature of the rope curve.
  3. Dragging coefficient of friction and angle are satisfying the following criteria for all points of the curve
  4. :
  5. Limit values of the tangential forces:
  6. : The forces at both ends of the rope and are satisfying the following inequality
  7. :
  8. : with
  9. : where is a geodesic curvature of the rope curve, is a curvature of a rope curve, is a coefficient of friction in the tangential direction.
  10. : If then
This generalization has been obtained by Konyukhov.