Conventional landing gear


Conventional landing gear, or tailwheel-type landing gear, is an aircraft undercarriage consisting of two main wheels forward of the center of gravity and a small wheel or skid to support the tail. The term taildragger is also used, although some claim it should apply only to those aircraft with a tailskid rather than a wheel.
The term "conventional" persists for historical reasons, but all modern jet aircraft and most modern propeller aircraft use tricycle gear.

History

In early aircraft, a tailskid made of metal or wood was used to support the tail on the ground. In most modern aircraft with conventional landing gear, a small articulated wheel assembly is attached to the rearmost part of the airframe in place of the skid. This wheel may be steered by the pilot through a connection to the rudder pedals, allowing the rudder and tailwheel to move together.
Before aircraft commonly used tailwheels, many aircraft were equipped with steerable tailskids, which operate similar to a tailwheel. When the pilot pressed the right rudder pedal — or the right footrest of a "rudder bar" in World War I — the skid pivoted to the right, creating more drag on that side of the plane and causing it to turn to the right. While less effective than a steerable wheel, it gave the pilot some control of the direction the craft was moving while taxiing or beginning the takeoff run, before there was enough airflow over the rudder for it to become effective.
Another form of control, which is less common now than it once was, is to steer using "differential braking", in which the tailwheel is a simple, freely castering mechanism, and the aircraft is steered by applying brakes to one of the mainwheels in order to turn in that direction. This is also used on some tricycle gear aircraft, with the nosewheel being the freely castering wheel instead. Like the steerable tailwheel/skid, it is usually integrated with the rudder pedals on the craft to allow an easy transition between wheeled and aerodynamic control.

Advantages

The tailwheel configuration offers several advantages over the tricycle landing gear arrangement, which make tailwheel aircraft less expensive to manufacture and maintain.
The conventional landing gear arrangement has disadvantages compared to nosewheel aircraft.
. If this aircraft were taxiing, the pilot would be unable to see the photographer
Jet aircraft generally cannot use conventional landing gear, as this orients the engines at a high angle, causing their jet blast to bounce off the ground and back into the air, preventing the elevators from functioning properly. This problem occurred with the third, or "V3" prototype of the German Messerschmitt Me 262 jet fighter. After the first four prototype Me 262 V-series airframes were built with retracting tailwheel gear, the fifth prototype was fitted with fixed tricycle landing gear for trials, with the sixth prototype onwards getting fully retracting tricycle gear. A number of other experimental and prototype jet aircraft had conventional landing gear, including the first successful jet, the Heinkel He 178, the Ball-Bartoe Jetwing research aircraft, and a single Vickers VC.1 Viking, which was modified with Rolls Royce Nene engines to become the world's first jet airliner.
Rare examples of jet-powered tailwheel aircraft that went into production and saw service include the British Supermarine Attacker naval fighter and the Soviet Yakovlev Yak-15. Both first flew in 1946 and owed their configurations to being developments of earlier propeller powered aircraft. The Attacker 's tailwheel configuration was a result of it using the Supermarine Spiteful's wing, avoiding expensive design modification or retooling. The engine exhaust was behind the elevator and tailwheel, reducing problems. The Yak-15 was based on the Yakovlev Yak-3 propeller fighter. Its engine was mounted under the forward fuselage. Despite its unusual configuration, the Yak-15 was easy to fly. Although a fighter, it was mainly used to prepare Soviet pilots for flying more advanced jet fighters.

Monowheel undercarriage

A variation of the taildragger layout is the monowheel landing gear.
To minimize drag, many modern gliders have a single wheel, retractable or fixed, centered under the fuselage, which is referred to as monowheel gear or monowheel landing gear. Monowheel gear is also used on some powered aircraft, where drag reduction is a priority, such as the Europa XS. Both monowheel gliders and monowheel power aircraft use retractable wingtip legs to prevent the wingtips from striking the ground. A monowheel aircraft may have a tailwheel or a nosewheel.

Training

Taildragger aircraft require more training time for student pilots to master. This was a large factor in the 1950s switch by most manufacturers to nosewheel-equipped trainers, and for many years nosewheel aircraft have been more popular than taildraggers. As a result, most Private Pilot Licence pilots now learn to fly in tricycle gear aircraft and only later transition to taildraggers.

Techniques

Landing a conventional geared aircraft can be accomplished in two ways.
Normal landings are done by touching all three wheels down at the same time in a three-point landing. This method does allow the shortest landing distance but can be difficult to carry out in crosswinds, as rudder control may be reduced severely before the tailwheel can become effective.
The alternative is the wheel landing. This requires the pilot to land the aircraft on the mainwheels while maintaining the tailwheel in the air with elevator to keep the angle of attack low. Once the aircraft has slowed to a speed that can ensure control will not be lost, but above the speed at which rudder effectiveness is lost, then the tailwheel is lowered to the ground.

Examples

Examples of tailwheel aircraft include:

Airplanes

Several aftermarket modification companies offer kits to convert many popular nose-wheel equipped aircraft to conventional landing gear. Aircraft for which kits are available include: