In the field of acoustics, a diaphragm is a transducer intended to inter-convert mechanical vibrations to sounds, or vice versa. It is commonly constructed of a thin membrane or sheet of various materials, suspended at its edges. The varying air pressure of sound waves imparts mechanical vibrations to the diaphragm which can then be converted to some other type of signal; examples of this type of diaphragm are found in microphones and the human eardrum. Conversely a diaphragm vibrated by a source of energy beats against the air, creating sound waves. Examples of this type of diaphragm are loudspeaker cones and earphone diaphragms and are found in air horns.
Loudspeaker
In a dynamic loudspeaker, a diaphragm is the thin, semi-rigid membrane attached to the voice coil, which moves in a magnetic gap, vibrating the diaphragm, and producing sound. It can also be called a cone, though not all speaker diaphragms are cone-shaped. Diaphragms are also found in headphones. Quality midrange and bass drivers are usually made from paper, paper composites and laminates, plastic materials such as polypropylene, or mineral/fiber filled polypropylene. Such materials have very high strength/weight ratios and tend to be relatively immune from flexing during large excursions. This allows the driver to react quickly during transitions in music and minimizes acoustical output distortion. If properly designed in terms of mass, stiffness, and damping, paper woofer/midrange cones can outperform many exotic drivers made from more expensive materials. Other materials used for diaphragms include polypropylene, polyetheretherketonepolycarbonate, Mylar, silk, glassfibre, carbon fibre, titanium, aluminium, aluminium-magnesium alloy, nickel, and beryllium. A paper woofer with a peak-to-peak excursion of 0.5 inches at 60 Hz undergoes a maximum acceleration of 92 "g"s. Paper-based cones account for approximately 85% of the cones sold worldwide. The ability of paper to be easily modified by chemical or mechanical means gives it a practical processing advantage not found in other common cone materials. The purpose of the cone/surround assembly is to accurately reproducethe voice coil signal waveform. Inaccurate reproduction of the voice coil signal results in acoustical distortion. The ideal for a cone/surround assembly is an extended range of linearity or "pistonic" motion characterized by i) minimal acoustical breakup of the cone material, ii) minimal standing wave patterns in the cone, and iii) linearity of the surrounds force-deflection curve. The cone stiffness/damping plus the surround's linearity/damping play a crucial role in accuracy of the reproduced voice coil signal waveform. This is the crux of high-fidelity stereo. The surround may be resin-treated cloth, resin-treated non-wovens, polymeric foams, or thermoplastic elastomers over-molded onto the cone body. An ideal surround has a linear force-deflection curve with sufficient damping to fully absorb vibrational transmissions from the cone/surround interface, and the "toughness" to withstand long-term vibration-induced fatigue. Sometimes the conical part and the outer surround are molded in one step and are one piece as commonly used for a Guitar speaker. Other types of speakers may use a thin membrane instead of a cone.
Microphone
can be thought of as speakers in reverse. The sound waves strike the thin diaphragm, causing it to vibrate. Microphone diaphragms, unlike speaker diaphragms, tend to be thin and flexible, since they need to absorb as much sound as possible. In a condenser microphone, the diaphragm is placed in front of a plate and is charged. In a dynamic microphone, the diaphragm is glued to a magnetic coil, similar to the one in a dynamic loudspeaker. The diaphragm in a microphone works similarly to the human eardrum.
Other uses
In a phonograph reproducer, the diaphragm is a flat disk of typically mica or isinglass that converts the mechanical vibration imparted on the buttress from the recorded groove into sound. In the case of acoustic recording the reproducer converts the sound into the motion of the needle that scribes the groove on the recording media.
