Digital image correlation and tracking


Digital image correlation and tracking is an optical method that employs tracking and image registration techniques for accurate 2D and 3D measurements of changes in images. This method is often used to measure full-field displacement and strains, and it is widely applied in many areas of science and engineering, with new applications being found all the time. Compared to strain gages and extensometers, the amount of information gathered about the fine details of deformation during mechanical tests is increased due to the ability to provide both local and average data using digital image correlation.

Overview

Digital image correlation techniques have been increasing in popularity, especially in applications due to its relative ease of implementation and use. Advances in computer technology and digital cameras have been the enabling technologies for this method and while white-light optics has been the predominant approach, DIC can be and has been extended to almost any imaging technology.
The concept of using cross-correlation to measure shifts in datasets has been known for a long time, and it has been applied to digital images since at least the early 1970s. The present-day applications are almost innumerable and include image analysis, image compression, velocimetry, and strain estimation. Much early work in DIC in the field of mechanics was led by researchers at the University of South Carolina in the early 1980s and has been optimized and improved in recent years. Commonly, DIC relies on finding the maximum of the correlation array between pixel intensity array subsets on two or more corresponding images, which gives the integer translational shift between them. It is also possible to estimate shifts to a finer resolution than the resolution of the original images, which is often called "subpixel" registration because the measured shift is smaller than an integer pixel unit. For subpixel interpolation of the shift, there are other methods that do not simply maximize the correlation coefficient. An iterative approach can also be used to maximize the interpolated correlation coefficient by using nonlinear optimization techniques. The nonlinear optimization approach tends to be conceptually simpler and can handle large deformations more accurately, but as with most nonlinear optimization techniques, it is slower.
The two-dimensional discrete cross correlation can be defined several ways, one possibility being:
Here f is the pixel intensity or the gray-scale value at a point in the original image, g is the gray-scale value at a point in the translated image, and are mean values of the intensity matrices f and g respectively.
However, in practical applications, the correlation array is usually computed using Fourier-transform methods, since the fast Fourier transform is a much faster method than directly computing the correlation.
Then taking the complex conjugate of the second result and multiplying the Fourier transforms together elementwise, we obtain the Fourier transform of the correlogram, :
where is the Hadamard product. It is also fairly common to normalize the magnitudes to unity at this point, which results in a variation called phase correlation.
Then the cross-correlation is obtained by applying the inverse Fourier transform:
At this point, the coordinates of the maximum of give the integer shift:

Deformation mapping

For deformation mapping, the mapping function that relates the images can be derived from comparing a set of subwindow pairs over the whole images.. The coordinates or grid points and are related by the translations that occur between the two images. If the deformation is small and perpendicular to the optical axis of the camera, then the relation between and can be approximated by a 2D affine transformation such as:
Here u and v are translations of the center of the sub-image in the X and Y directions respectively. The distances from the center of the sub-image to the point are denoted by and. Thus, the correlation coefficient rij is a function of displacement components and displacement gradients
DIC has proven to be very effective at mapping deformation in macroscopic mechanical testing, where the application of specular markers or surface finishes from machining and polishing provide the needed contrast to correlate images well. However, these methods for applying surface contrast do not extend to the application of freestanding thin films for several reasons. First, vapor deposition at normal temperatures on semiconductor grade substrates results in mirror-finish quality films with RMS roughnesses that are typically on the order of several nanometers. No subsequent polishing or finishing steps are required, and unless electron imaging techniques are employed that can resolve microstructural features, the films do not possess enough useful surface contrast to adequately correlate images. Typically this challenge can be circumvented by applying paint that results in a random speckle pattern on the surface, although the large and turbulent forces resulting from either spraying or applying paint to the surface of a freestanding thin film are too high and would break the specimens. In addition, the sizes of individual paint particles are on the order of μms, while the film thickness is only several hundred nanometers, which would be analogous to supporting a large boulder on a thin sheet of paper.
Very recently, advances in pattern application and deposition at reduced length scales have exploited small-scale synthesis methods including nano-scale chemical surface restructuring and photolithography of computer-generated random specular patterns to produce suitable surface contrast for DIC. The application of very fine powder particles that electrostatically adhere to the surface of the specimen and can be digitally tracked is one approach. For Al thin films, fine alumina abrasive polishing powder was initially used since the particle sizes are relatively well controlled, although the adhesion to Al films was not very good and the particles tended to agglomerate excessively. The candidate that worked most effectively was a silica powder designed for a high temperature adhesive compound, which was applied through a plastic syringe. A light blanket of powder would coat the gage section of the tensile sample and the larger particles could be blown away gently. The remaining particles would be those with the best adhesion to the surface. While the resulting surface contrast is not ideal for DIC, the high intensity ratio between the particles and the background provide a unique opportunity to track the particles between consecutive digital images taken during deformation. This can be achieved quite straightforwardly using digital image processing techniques. Subpixel tracking can be achieved by a number of correlation techniques, or by fitting to the known intensity profiles of particles. Photolithography and Electron Beam Lithography can be used to create micro tooling for , and the . Stamp inks can be chosen which are appropriate for optical DIC, SEM-DIC, and .

Digital volume correlation

Digital Volume Correlation extends the 2D-DIC algorithms into three dimensions to calculate the full-field 3D deformation from a pair of 3D images. This technique is distinct from 3D-DIC, which only calculates the 3D deformation of an exterior surface using conventional optical images. The DVC algorithm is able to track full-field displacement information in the form of voxels instead of pixels. The theory is similar to above except that another dimension is added: the z-dimension. The displacement is calculated from the correlation of 3D subsets of the reference and deformed volumetric images, which is analogous to the correlation of 2D subsets described above.
DVC can be performed using volumetric image datasets. These images can be obtained using confocal microscopy, X-ray computed tomography, Magnetic Resonance Imaging or other techniques. Similar to the other DIC techniques, the images must exhibit a distinct, high-contrast 3D "speckle pattern" to ensure accurate displacement measurement.
DVC was first developed in 1999 to study the deformation of trabecular bone using X-ray computed tomography images. Since then, applications of DVC have grown to include granular materials, metals, foams, composites and biological materials. To date it has been used with images acquired by MRI imaging, Computer Tomography, microCT, and confocal microscopy. DVC is currently considered to be ideal in the research world for 3D quantification of local displacements, strains, and stress in biological specimens. It is preferred because of the non-invasiveness of the method over traditional experimental methods.
Two of the key challenges are improving the speed and reliability of the DVC measurement. The 3D imaging techniques produce noisier images than conventional 2D optical images, which reduces the quality of the displacement measurement. Computational speed is restricted by the file sizes of 3D images, which are significantly larger than 2D images. For example, an 8-bit pixel 2D image has a file size of 1 MB, while an 8-bit voxel 3D image has a file size of 1 GB. This can be partially offset using parallel computing.

Applications

Digital image correlation has demonstrated uses in the following industries:
It has also been used for mapping earthquake deformation.