Dry lubricant


Dry lubricants or solid lubricants are materials that, despite being in the solid phase, are able to reduce friction between two surfaces sliding against each other without the need for a liquid oil medium.
The two main dry lubricants are graphite and molybdenum disulfide. They offer lubrication at temperatures higher than liquid and oil-based lubricants operate. Dry lubricants are often used in applications such as locks or dry lubricated bearings. Such materials can operate up to 350 °C in oxidizing environments and even higher in reducing / non-oxidizing environments. The low-friction characteristics of most dry lubricants are attributed to a layered structure on the molecular level with weak bonding between layers. Such layers are able to slide relative to each other with minimal applied force, thus giving them their low friction properties.
However, a layered crystal structure alone is not necessarily sufficient for lubrication. In fact, there are some solids with non-lamellar structures that function well as dry lubricants in some applications. These include certain soft metals, polytetrafluroethylene, some solid oxides, rare-earth fluorides, and even diamond.
Limited interest has been shown in low friction properties of compacted oxide glaze layers formed at several hundred degrees Celsius in metallic sliding systems. However, practical use is still many years away due to their physically unstable nature.
The four most commonly used solid lubricants are:
  1. Graphite. Used in air compressors, food industry, railway track joints, brass instrument valves, piano actions, open gear, ball bearings, machine-shop works, etc. It is also very common for lubricating locks, since a liquid lubricant allows particles to get stuck in the lock worsening the problem. It is often used to lubricate the internal moving parts of firearms in sandy environments.
  2. Molybdenum disulfide. Used in CV joints and space vehicles. Does lubricate in vacuum.
  3. Hexagonal boron nitride. Used in space vehicles. Also called "white graphite."
  4. Tungsten disulfide. Similar usage as molybdenum disulfide, but due to the high cost only found in some dry lubricated bearings.
Graphite and molybdenum disulfide are the predominant materials used as dry lubricants.

Structure-function relationship

The lubricity of many solids is attributable to a lamellar structure. The lamellae orient parallel to the surface in the direction of motion and slide easily over each other resulting in low friction and preventing contact between sliding components even under high loads. Large particles perform best on rough surfaces at low speed, finer particles on smoother surfaces and at higher speeds. These materials may be added in the form of dry powder to liquid lubricants to modify or enhance their properties.
Other components that are useful solid lubricants include boron nitride, polytetrafluorethylene, talc, calcium fluoride, cerium fluoride, and tungsten disulfide.

Applications

Solid lubricants are useful for conditions when conventional lubricants are inadequate, such as:
is structurally composed of planes of polycyclic carbon atoms that are hexagonal in orientation. The distance of carbon atoms between planes is longer and, therefore, the bonding is weaker.
Graphite is best suited for lubrication in air. Water vapor is a necessary component for graphite lubrication. The adsorption of water reduces the bonding energy between the hexagonal planes of the graphite to a lower level than the adhesion energy between a substrate and the graphite. Because water vapor is a requirement for lubrication, graphite is not effective in vacuum. Because it is electrically conductive, graphite can promote galvanic corrosion. In an oxidative atmosphere, graphite is effective at high temperatures up to 450 °C continuously and can withstand much higher temperature peaks.
Graphite is characterized by two main groups: natural and synthetic.
For applications where only a minor lubricity is needed and a more thermally insulating coating is required, then amorphous graphite would be chosen.

[Molybdenum disulfide]

MoS2 is mined from some sulfide-rich deposits and refined to achieve a purity suitable for lubricants. Like graphite, MoS2 has a hexagonal crystal structure with the intrinsic property of easy shear. MoS2 lubrication performance often exceeds that of graphite and is effective in vacuum as well, whereas graphite is not. The temperature limitation of MoS2 at 400 °C is restricted by oxidation. Particle size and film thickness are important parameters that should be matched to the surface roughness of the substrate. Large particles may result in excessive wear by abrasion caused by impurities in the MoS2, and small particles may result in accelerated oxidation.

Boron nitride

is a ceramic powder lubricant. The most interesting lubricant feature is its high temperature resistance of 1200 °C service temperature in an oxidizing atmosphere. Furthermore, boron nitride has a high thermal conductivity.

Polytetrafluorethylene

is widely used as an additive in lubricating oils and greases. Due to the low surface energy of PTFE, stable unflocculated dispersions of PTFE in oil or water can be produced. Contrary to the other solid lubricants discussed, PTFE does not have a layered structure. The macro molecules of PTFE slip easily along each other, similar to lamellar structures. PTFE shows one of the smallest coefficients of static and dynamic friction, down to 0.04. Operating temperatures are limited to about 260 °C.

Application methods

Spraying/dipping/brushing

Dispersion of solid lubricant as an additive in oil, water, or grease is most commonly used. For parts that are inaccessible for lubrication after assembly, a dry film lubricant can be sprayed. After the solvent evaporates, the coating cures at room temperature to form a solid lubricant. Pastes are grease-like lubricants containing a high percentage of solid lubricants used for assembly and lubrication of highly loaded, slow-moving parts. Black pastes generally contain MoS2. For high temperatures above 500 °C, pastes are composed on the basis of metal powders to protect metal parts from oxidation necessary to facilitate disassembly of threaded connections and other assemblies.

Free powders

Dry-powder tumbling is an effective application method. The bonding can be improved by prior phosphating of the substrate. Use of free powders has its limitations, since adhesion of the solid particles to the substrate is usually insufficient to provide any service life in continuous applications. However, to improve running-in conditions or in metal-forming processes, a short duration of the improved slide conditions may suffice.

Anti-friction coatings

Anti-friction coatings are "lubricating paints" consisting of fine particles of lubricating pigments, such as molydisulfide, PTFE or graphite, blended with a binder. After application and proper curing, these "slippery" or dry lubricants bond to the metal surface and form a dark gray solid film. Many dry film lubricants contain special rust inhibitors which offer exceptional corrosion protection. Most long-wearing films are of the bonded type but are still restricted to applications where sliding distances are not too long. AF coatings are applied where fretting and galling is a problem, where operating pressures exceed the load-bearing capacities of ordinary oils and greases, where smooth running in is desired, where clean operation is desired, and where parts may be stored for long periods.

Composites

Self-lubricating composites: Solid lubricants such as PTFE, graphite, MoS2 and some other anti-friction and anti-wear additives are often compounded in polymers and all kind of sintered materials. MoS2, for example, is compounded in materials for sleeve bearings, elastomer O-rings, carbon brushes, etc. Solid lubricants are compounded in plastics to form a "self-lubricating" or "internally lubricated" thermoplastic composite. For example, PTFE particles compounded in the plastic form a PTFE film over the mating surface, resulting in a reduction of friction and wear. MoS2 compounded in nylon reduces wear, friction and stick-slip. Furthermore, it acts as a nucleating agent effecting in a very fine crystalline structure. The primary use of graphite lubricated thermoplastics is in applications operating in aqueous environments.