Flare (countermeasure)


A flare or decoy flare is an aerial infrared countermeasure used by a plane or helicopter to counter an infrared homing surface-to-air missile or air-to-air missile. Flares are commonly composed of a pyrotechnic composition based on magnesium or another hot-burning metal, with burning temperature equal to or hotter than engine exhaust. The aim is to make the infrared-guided missile seek out the heat signature from the flare rather than the aircraft's engines.

Tactics

In contrast to radar-guided missiles, IR-guided missiles are very difficult to find as they approach aircraft. They do not emit detectable radar, and they are generally fired from behind, directly toward the engines. In most cases, pilots have to rely on their wingmen to spot the missile's smoke trail and alert them. Since IR-guided missiles have a shorter range than their radar-guided counterparts, good situational awareness of altitude and potential threats continues to be an effective defense. More advanced electro-optical systems can detect missile launches automatically from the distinct thermal emissions of a missile's rocket motor.
Once the presence of a "live" IR missile is indicated, flares are released by the aircraft in an attempt to decoy the missile; some systems are automatic, while others require manual jettisoning of the flares.
The aircraft would then pull away at a sharp angle from the flare and reduce engine power in attempt to cool the thermal signature. Optimally, the missile's seeker head is then confused by this change in temperature and flurry of new signatures, and therefore follows the flare rather than the aircraft. The most modern IR-guided missiles have sophisticated on-board electronics that help discriminate between flares and targets, reducing the effectiveness of countermeasures.
Since insurgents and terrorists are increasingly targeting helicopters with missiles, because helicopters are slower-moving, there is an increasing trend to equip military helicopters with flare countermeasures. Consequently, flare dispensers are now fitted to helicopters. Almost all of the UK's helicopters, whether they are transport or attack models, are equipped with flare dispenser or missile approach warning systems. Similarly, the US armed forces have adopted defensive technology on their helicopters.

Usage

Apart from military use, some civilian aircraft are also equipped with countermeasure flares, against terrorism: the Israeli airline El Al, having been the target of the failed 2002 airliner attack, in which shoulder-launched surface-to-air missiles were fired at an airliner while taking off, began equipping its fleet with radar-based, automated flare release countermeasures from June 2004. This caused concerns in some European countries, which proceeded to ban such aircraft from landing at their airports.

Process

A flare goes through three main stages: ignition, deployment, and decoying.

Ignition

Most flares, like the MJU-27A/B flares, must be kept in an airtight storage compartment before deployment. These flares, known as pyrophoric flares, are made of special materials that ignite when they come in contact with the air. This is a safety and convenience factor, since attempting to ignite a flare inside the fuselage and then deploying it is risky. However pyrotechnic flares also exist, and offer their own safety benefit; requiring an external ignition method, an accidental leak or puncture in the storage compartment would not result in a catastrophic fire on board the aircraft as with a pyrophoric flare.

Deployment

Flares are most commonly gravity-fed from a dispenser inside the aircraft's fuselage. These dispensers can be programmed by the pilot or ground crew to dispense flares in short intervals, one at a time, long intervals, or in clusters. Most currently used flares are of the pyrophoric variety, and thus the dispensers do not have to ignite and deploy the flare at the same time. With pyrotechnic flares, a lanyard automatically pulls off a friction cap covering the exposed end of the flare as it falls from the dispenser. A friction surface inside the cap rubs against the exposed end of the flare and ignites the flare.

Decoying

Flares burn at thousands of degrees Celsius, which is much hotter than the exhaust of a jet engine. IR missiles seek out the hotter flame, believing it to be an aircraft in afterburner or the beginning of the engine's exhaust source.
As the more modern infrared seekers tend to have spectral sensitivity tailored to more closely match the emissions of airplanes and reject other sources, the modernized decoy flares have their emission spectrum optimized to also match the radiation of the airplane. In addition to spectral discrimination, the CCMs can include trajectory discrimination and detection of size of the radiation source.
The newest generation of the FIM-92 Stinger uses a dual IR and UV seeker head, which allows for a redundant tracking solution, effectively negating the effectiveness of modern decoy flares. While research and development in flare technology has produced an IR signature on the same wavelength as hot engine exhaust, modern flares still produce a notably different UV signature than an aircraft engine burning kerosene jet-fuel.

Materials used

For the infrared generating charge, two approaches are possible: pyrotechnic and pyrophoric.
As stored, chemical-energy-source IR-decoy flares contain pyrotechnic compositions, liquid or solid pyrophoric substances, or liquid or solid highly flammable substances.
Upon ignition of the decoy flare, a strongly exothermal reaction is started, releasing infrared energy and visible smoke and flame, emission being dependent on the chemical nature of the payload used.
There is a wide variety of calibres and shapes available for aerial decoy flares. Due to volume storage restrictions on board platforms, many aircraft of American origin use square decoy flare cartridges. Nevertheless, cylindrical cartridges are also available on board American aircraft, such as MJU 23/B on the B-1 Lancer or MJU-8A/B on the F/A-18 Hornet; however, these are used mainly on board French aircraft and those of Russian origin, e.g. PPI-26 IW on the MiG 29.
layer ; the wrapping self-adhesive polyester reinforced aluminum foil ; and a front washer.
Square calibres and typical decoy flares:
Cylindrical calibres and typical decoy flares:
Pyrotechnic flares use a slow-burning fuel-oxidizer mixture that generates intense heat. Thermite-like mixtures, e.g. Magnesium/Teflon/Viton, are common. Other combinations include ammonium perchlorate/anthracene/magnesium, or can be based on red phosphorus.
To adjust the emission characteristics to match closer the spectrum of jet engines, charges on the base of double base propellants. These compositions can avoid the metal content and achieve cleaner burning without the prominent smoke trail.

Blackbody payloads

Certain pyrotechnic compositions, for example MTV, give a great flame emission upon combustion and yield a temperature-dependent signature and can be understood as gray bodies of high emissivity. Such payloads are called blackbody payloads. Other payloads, like iron/potassium perchlorate pellets, only yield a low flame emission but also show temperature-dependent signature. Nevertheless, the lower combustion temperature as compared to MTV results in a lower amount of energy released in the short-wavelength IR range. Other blackbody payloads include ammonium perchlorate/anthracene/magnesium and hydroxyl-terminated polybutadiene binder.

Spectrally balanced payloads

Other payloads provide large amounts of hot carbon dioxide upon combustion and thus provide a temperature-independent selective emission in the wavelength range between 3 and 5 μm. Typical pyrotechnic payloads of this type resemble whistling compositions and are often made up from potassium perchlorate and hydrogen lean organic fuels.
Other spectrally balanced payloads are made up similarly as double base propellants and contain nitrocellulose, and other esters of nitric acid or nitro compounds as oxidizers such as e.g. hexanitroethane and nitro compounds and nitramines as high energy fuels. The main advantage of the latter payloads is their low visibility due to the absence of metals such as sodium and potassium that may be either easily thermally excited and give prominent emissions or give condensed reaction products, which would cause a distinct smoke trail.

Pyrophoric flares

Pyrophoric flares work on the principle of ejecting a special pyrophoric material out of an airtight cartridge, usually using a gas generator, e.g. a small pyrotechnic charge or pressurized gas. The material then self-ignites in contact with air. The materials can be solid, e.g. iron platelets coated with ultrafine aluminium, or liquid, often organometallic compounds; e.g. alkyl aluminium compounds, e.g. triethylaluminium. Pyrophoric flares may have reduced effectiveness at high altitudes, due to lower air temperature and lower availability of oxygen; however oxygen can be co-ejected with the pyrophoric fuel.
The advantage of alkyl aluminium and similar compounds is the high content of carbon and hydrogen, resulting in bright emission lines similar to spectral signature of burning jet fuel. Controlled content of solid combustion products, generating continuous black-body radiation, allows further matching of emission characteristics to the net infrared emissions of fuel exhaust and hot engine components.
The flames of pyrophoric fuels can also reach the size of several metres, in comparison with about less than one metre flame of MTV flares. The trajectory can be also influenced by tailoring the aerodynamic properties of the ejected containers.
Solid pyrophoric payloads are based on iron platelets coated with a porous aluminium layer. Based on the very high specific surface area of aluminium those platelets instantaneously oxidize upon contact with air. In contrast to triethylaluminium combustion, these platelets yield a temperature-dependent signature.

Highly flammable payloads

These payloads contain red phosphorus as an energetic filler. The red phosphorus is mixed with organic binders to give brushable pastes that can be coated on thin polyimide platelets. The combustion of those platelets yields a temperature-dependent signature. Endergonic additives such as highly dispersed silica or alkali halides may further lower the combustion temperature.