A forwarding information base, also known as a forwarding table or MAC table, is most commonly used in network bridging, routing, and similar functions to find the proper output network interface to which the input interface should forward a packet. It is a dynamic table that maps MAC addresses to ports. It is the essential mechanism that separates network switches from Ethernet hubs. Content-addressable memory is typically used to efficiently implement the FIB, thus it is sometimes called a CAM table.
The role of an Ethernet switch is to forward Ethernet frames from one port to another. The presence of a FIB is one attribute that separates a switch from a hub. Without a functional FIB, all frames received by a network switch would be echoed back out to all other ports, much like an Ethernet hub. In bridging packets between ports, a switch should only emit a frame on the port where the destination network device resides, unless the frame is for all nodes on the switch, multiple nodes or if the switch doesn't know where the destination device resides. Switches learn the port on which they first saw a particular source address and associate that port with that address. When the bridge subsequently receives a frame with a destination address in its FIB, it sends the frame out the port stored in the FIB entry. The FIB is a memory construct used by Ethernet switch to map a station's MAC address to the switch portthe station is connected to. This allows switches to facilitate communications between connected stations at high speed.
Frame Relay
While the exact mechanics of a forwarding table is implementation-specific, the general model for Frame Relay is that switches have statically defined forwarding tables, one per interface. When a frame with a given data link connection identifier is received on one interface, the table associated with that interface gives the outgoing interface, and the new DLCI to insert into the frame's address field.
Asynchronous transfer mode
ATM switches have link-level forwarding tables much like those used in Frame Relay. Rather than a DLCI, however, interfaces have forwarding tables that specify the outgoing interface by virtual path identifier and virtual circuit identifier. These tables may be configured statically, or they can be distributed by the Private Network-to-Network Interface protocol. When PNNI is in use, the ATM switches at the edges of the network map one of the standard ATM end-to-end identifiers, such as an NSAP address, to the next-hop VPI/VCI.
Multiprotocol label switching
MPLS has many similarities, at the forwarding level, to ATM. The label edge routers at the edges of an MPLS cloud map between the end-to-end identifier, such as an IP address, and a link-local label. At each MPLS hop, there is a forwarding table that tells the label switched router which outgoing interface is to receive the MPLS packet, and what label to use when sending the packet out that interface.
addresses, such as IP addresses, are used on different types of media and can be handled similarly in all cases.
Forwarding
FIBs are optimized for fast lookup of destination addresses and can improve performance of forwarding compared to using the routing information base directly. The RIB is optimized for efficient updating by routing protocols and other control plane methods, and contain the full set of routes learned by the router. Earlier implementations cached only a subset of the routes most frequently used in actual forwarding, and this worked reasonably well for enterprises where there is a meaningful most-frequently-used subset. Routers used for accessing the entire Internet, however, experienced severe performance degradation in refreshing routes cached in a small FIB, and various implementations moved to having FIBs in one-to-one correspondence with the RIB.
FIBs can also play a role in an Internetbest current practice of ingress filtering. Though the simplest form of ingress filtering is to use access-control lists to drop packets with improper source addresses, the use of access lists becomes difficult on routers with a large number of adjacent networks, and traditional access lists are not used in high-performance router forwarding paths. While the IETF document BCP 38 on ingress filtering does not specify a method of implementing source address filtering, some router vendors have implemented a mechanism which employs lookups in the router's tables to perform this check. This is often implemented as a lookup in the FIB of the source address of the packet. If the interface has no route to the source address, the packet is assumed to be part of a denial of service attack, using a spoofed source address, and the router discards the packet. When the router is multihomed, ingress filtering becomes more complex. There are perfectly reasonable operational scenarios in which a packet could arrive on one interface, but that specific interface might not have a route to the source address. For the routers near the edge of the Internet, packet filters can provide a simpler and more effective solution than methods that employ routing information lookup, though this approach can be challenging when managing routers which are reconfigured often. Ingress filtering for multihomed routers will accept the packet if there is a route back to its source address from any interface on the router. For this type of filtering, the router may also maintain an adjacency table, also organized for fast lookup, that keeps track of the router interface addresses that are on all directly connected routers.
Quality of service
provides an additional method to select outgoing interfaces, based on a field that indicates the forwarding priority of the packet, as well as the preference of the packet to be dropped in the presence of congestion. Routers that support differentiated service not only have to look up the output interface for the destination address, but need to send the packet to the interface that best matches the differentiated services requirements. In other words, as well as matching the destination address, the FIB has to match differentiated services code points.
Access control and accounting
Specific router implementations may, when a destination address or other FIB criterion is matched, specify another action to be done before forwarding, or apply an access control list that may cause the packet to be dropped.
Attacks
CAM tables are often the target of layer 2 network attacks in a local area network to set up man-in-the-middle attacks. A threat agent which has control of a device connected to an Ethernet switch can attack the switch's CAM table. This attack usually involves exploiting a vulnerability in switch design that appears when the switch runs out of space to record all of the MAC address to port mappings it learns. If the table fills up due to MAC flooding, most switches are no longer able to reliably add new MAC addresses. As a consequence, the switch will fall back to forwarding Ethernet frames from an ingress port to all other ports. This can enable the attacker to capture traffic from all devices connected to the same switch and degrades network performance.
