GM Roto Hydramatic transmission
Roto Hydramatic was an automatic transmission built by General Motors and used on some Oldsmobile, Pontiac and Holden models from 1961-1965. It was based on the earlier, four-speed Hydramatic, but was more compact, providing only three forward speeds plus a small 8" fluid coupling with a stator inside of the fluid coupling. Oldsmobile, one of the users of this transmission, called the fluid couplings stator the "Accel-A-Rotor." The lightweight, aluminum-cased transmission was sometimes nicknamed the "Slim Jim." HydraMatic Division calls the Roto a four range, three gear HydraMatic. It counts the stator multiplication at 3.50:1 as a first gear, and when road speed and the two coupling halves speed match, it counts the same gear with fluid now passing straight through the stator as 2nd gear at 2.93 to one. Second gear has a ratio of 1.56 and because the fluid coupling is drained for this gear ratio making the front clutch apply makes this a rare automatic that is in FULL mechanical lock-up in second gear. Fourth range the coupling fills releasing the front clutch makes a ratio of 1 to 1. This transmission, like single and dual range, and dual coupling hydramatics also have the feature of split torque in the transmission whereby in fourth or high gear only 40-to 50% depending on transmission, 40% in Roto's case, but because of the design the coupling is only required to carry 40% of the engine torque. The rest is is in full mechanical connection making these hydramatics the most efficient automatic until the wide spread use of the lock-up torque converter.
Roto's downfall was the 2-3 range or 1-2 gear change because it is not only a huge ratio jump from 2-3 range or 1-2 shift from 2.93 to 1.56, but also there is no fluid slippage in the coupling because the coupling drains to engage or apply the front clutch and so the trans goes to full mechanical connection. The other downfall of Roto HydraMatic was the extreme oil pressures in the small 8" fluid coupling which caused transmission leaks. All HydraMatic transmissions suffer some shift quality with today's ATF fluid. The original Type "A" fluid that these transmissions take is available only at O'Reilly Auto Parts.
There were two models of the Roto Hydramatic: the lightweight Model 5, which weighed and had ratios of 3.03, 1.58, and 1.00, and the larger Model 10, which weighed and had ratios of 3.50, 2.93, 1.56, and 1.00.
Overview
In 1961-62, the "Model 5" was used on the Opel Kapitan, Vauxhall Velox, Vauxhall Cresta and EK Holden. The Roto Hydramatic was cheaper than the previous Hydramatic, but its slower, softer shifts sacrificed performance for refinement. Owners discovered that it was also less durable than Hydramatic, and was prone to various mechanical problems.The Roto Hydramatic was phased out after the 1964 model year in favor of the two-speed Super Turbine 300 and three-speed Turbo-Hydramatic. As with previous Hydramatic transmissions, auto safety experts criticized GM for the Hydramatic design which had a shift quadrant sequence of Park-Neutral-Drive-Second-Low-Reverse due to the placement of reverse adjacent to a forward gear as opposed to the more common P-R-N-D-S-L sequence found in most other automatic transmissions at the time that placed "reverse" between "park" and "neutral", which was also incorporated in the new Turbo Hydramatic design introduced on Buicks and Cadillacs in 1964, and then other GM divisions in 1965.
Applications
The Roto Hydramatic was used in all full-sized Oldsmobile models including the Dynamic 88, Super 88, Ninety-Eight and Starfire from 1961-1964 as well as the compact Oldsmobile F-85 from 1961-1963. Pontiac used the Roto Hydramatic from 1961-1964 on its shorter-wheelbase full-sized cars including the Catalina, Ventura and Grand Prix, but continued with the older four-speed Super Hydramatic design in the longer-wheelbase Star Chief and Bonneville models. It is believed Pontiac was made to take Roto in the short wheelbase models by the Corporation. The reason behind that was Oldsmobile's sales volume alone was not profitable enough to use Roto all by itself, therefore Pontiac was used because at that time Pontiac was having tremendous sales and in fact from 1961 to the end of the decade was number three in sales behind Chevy and Ford.Technical details
In the familiar Oldsmobile and Pontiac shift quadrant, P-R-N-D-S-L or P-N-D-S-L-R, the "S" quadrant was for "Super" and not second. This shift arrangement with the "S" only applies to floor shift Pontiacs and all Pontiacs in 1964. In previous Pontiacs including 1963 models with column shift the shift quadrant read 'DR' which refers back to the old Dual Range nomenclature which means drive left is fourth range and drive right is 3rd range. In the earlier four-speed Hydra-Matic, the "S" or "Super" quadrant was actually third gear, allowing 1-2-3 shifts. This nomenclature was also used by Mercedes-Benz with the introduction of the four-speed type-3 automatic transmission. As with the Hydra-Matic, the "L" position was actually 1st and 2nd gears, holding the transmissions from shifting above 2nd gear. In Roto the L position meant 3.50 as first range, changing due to 2.93. Roto engineers consider this two driving ranges.On Pontiacs with the exception 1964 model and all floor shift automatics, the shift indicator reads the same for Roto or the Super HydraMatic and that is; 'DR' drive left and drive right or fourth range left and drive right 3rd range.
Remember Roto HydraMatic is considered by HydraMatic Division as a three speed four range automatic and that is why the shift quadrant is the same between the 4 speed Super HydraMatic and the Four range Roto HydraMatic.
The Roto-Hydramatic did not have a conventional fluid coupling or torque converter but had an internal fluid coupling with a torque multiplier. There was no real bell housing; instead, the Roto-Hydramatic had a kind of flange connecting the transmission to the engine. The power flow from the engine crankshaft to the transmission input shaft was connected via a flywheel containing a set of springs to absorb torsional vibrations at the flexplate.
Performance
The shifting sequence was very different and much rougher than the Hydra-Matics that preceded it, or the Super Turbines and Turbo Hydramatics that followed it. The shift from 1st to 2nd or 2nd to 3rd range was long and drawn-out, ending with a harsh shift. The reason for this was that three things were happening. Not only was the transmission shifting to a very much higher range by refilling the fluid coupling. Direct drive is achieved by splitting engine power between the fluid coupling and the front clutch, which are both applied to provide third gear, effectively locking the planetary gearsets and forcing them to spin at engine speed. The design is unique in that it provides third gear by applying first and second gears at the same time.It can be said that Pontiac Division was probably made to use Roto so as to make Roto worth its money because Oldsmobile division didn't make enough units to justify its existence. Pontiac only used Roto from 1961-1964 in Catalina, Ventura, and Grand Prix. Bonneville and StarChief continued to use the 4 speed dual coupling called Super HydraMatic until the end of the 1964 model run.
Comparisons
By historical context of comparison, the '50 Packard Ultramatic which was a torque converter applied two speed lock-up design with high and low range for four forward speeds and the '50 Studebaker/Detroit Gear featured a lock-up torque converter with three forward speeds. The lock-up feature of Packard's Ultramatic and Studebaker's DG 250 is commonplace in virtually all modern 4+speed, overdrive automatic transmissions.Model 5
The smaller model 5 Roto Hydramatic uses the same principles of operation as the model 10. It is lighter and much shorter in length — a necessary design parameter considering its placement in compact cars. The model 5 is not related to the "Dual Path Dynaflow" transmission used in the Buick Special and Skylark models of 1961-1963. Buick's Dual Path was an air-cooled 2-speed unit with a planetary gearset inside the flywheel-mounted torque converter. The first Pontiac Tempests used a modified version of the Powerglide transaxle shared with the Chevrolet Corvair. But unlike the Corvairs, the TempesTorque was connected via a flexible drive shaft to an unconventional slant-4 or an aluminum 215 c.i. V-8, which would be later sold to the Rover Group and be renamed the 3500 V-8.The smaller 61-05 as fitted to the Vauxhall Cresta was dubbed the "smoothamatic from Luton" in Cars Illustrated in Feb 1961 being quite taken with the overall refinement with the test car, also noting that full throttle starts could be made on slushy roads, perhaps giving away the rather tall 1st gear and minimal torque conversion. They also stated that the gearshifts were so smooth as to be practically imperceptible. The magazine The Motor, Dec 1960, also praised the high standard of smoothness with very lively performance. The performance was claimed to be almost as fast as with synchromesh gears and the 2-3 shift could be so gradual in gentle driving that the driver did not always realise it has happened. Certainly, the examples the author drove were equal to this and it seemed disappointing when the 61-05 model was discontinued in favour of the Powerglide in 1965.