Heat capacity ratio


In thermal physics and thermodynamics, the heat capacity ratio, also known as the adiabatic index, the ratio of specific heats, or Laplace's coefficient, is the ratio of the heat capacity at constant pressure to heat capacity at constant volume. It is sometimes also known as the isentropic expansion factor and is denoted by for an ideal gas or , the isentropic exponent for a real gas. The symbol gamma is used by aerospace and chemical engineers.
where is the heat capacity, the molar heat capacity and the specific heat capacity of a gas. The suffixes and refer to constant pressure and constant volume conditions respectively.
The heat capacity ratio is important for its applications in thermodynamical reversible processes, especially involving ideal gases; the speed of sound depends on that factor.
To understand this relation, consider the following thought experiment. A closed pneumatic cylinder contains air. The piston is locked. The pressure inside is equal to atmospheric pressure. This cylinder is heated to a certain target temperature. Since the piston cannot move, the volume is constant. The temperature and pressure will rise. When the target temperature is reached, the heating is stopped. The amount of energy added equals, with representing the change in temperature. The piston is now freed and moves outwards, stopping as the pressure inside the chamber reaches atmospheric pressure. We assume the expansion occurs without exchange of heat. Doing this work, air inside the cylinder will cool to below the target temperature. To return to the target temperature, the air must be heated, but is no longer under constant volume, since the piston is free to move as the gas is reheated. This extra heat amounts to about 40% more than the previous amount added. In this example, the amount of heat added with a locked piston is proportional to, whereas the total amount of heat added is proportional to. Therefore, the heat capacity ratio in this example is 1.4.
Another way of understanding the difference between and is that applies if work is done to the system, which causes a change in volume, or if work is done by the system, which changes its temperature. applies only if – that is, the work done – is zero. Consider the difference between adding heat to the gas with a locked piston and adding heat with a piston free to move, so that pressure remains constant. In the second case, the gas will both heat and expand, causing the piston to do mechanical work on the atmosphere. The heat that is added to the gas goes only partly into heating the gas, while the rest is transformed into the mechanical work performed by the piston. In the first, constant-volume case there is no external motion, and thus no mechanical work is done on the atmosphere; is used. In the second case, additional work is done as the volume changes, so the amount of heat required to raise the gas temperature is higher for this constant pressure case.

Ideal gas relations

For an ideal gas, the heat capacity is constant with temperature. Accordingly, we can express the enthalpy as and the internal energy as. Thus, it can also be said that the heat capacity ratio is the ratio between the enthalpy to the internal energy:
Furthermore, the heat capacities can be expressed in terms of heat capacity ratio and the gas constant :
where is the amount of substance in moles.
Mayer's relation allows to deduce the value of from the more commonly tabulated value of :

Relation with degrees of freedom

The heat capacity ratio for an ideal gas can be related to the degrees of freedom of a molecule by
Thus we observe that for a monatomic gas, with 3 degrees of freedom:
while for a diatomic gas, with 5 degrees of freedom :
For example, the terrestrial air is primarily made up of diatomic gases, and at standard conditions it can be considered to be an ideal gas. The above value of 1.4 is highly consistent with the measured adiabatic indices for dry air within a temperature range of 0–200 °C, exhibiting a deviation of only 0.2%.

Real-gas relations

As temperature increases, higher-energy rotational and vibrational states become accessible to molecular gases, thus increasing the number of degrees of freedom and lowering. For a real gas, both and increase with increasing temperature, while continuing to differ from each other by a fixed constant, which reflects the relatively constant difference in work done during expansion for constant pressure vs. constant volume conditions. Thus, the ratio of the two values,, decreases with increasing temperature. For more information on mechanisms for storing heat in gases, see the gas section of specific heat capacity. While at 273 K, Monatomic gases such as the noble gases He, Ne, and Ar all have the same value of, that being 1.664. However, once you start getting in to diatomic gases and gas compounds, the values for change quite often.

Thermodynamic expressions

Values based on approximations are in many cases not sufficiently accurate for practical engineering calculations, such as flow rates through pipes and valves. An experimental value should be used rather than one based on this approximation, where possible. A rigorous value for the ratio can also be calculated by determining from the residual properties expressed as
Values for are readily available and recorded, but values for need to be determined via relations such as these. See relations between specific heats for the derivation of the thermodynamic relations between the heat capacities.
The above definition is the approach used to develop rigorous expressions from equations of state, which match experimental values so closely that there is little need to develop a database of ratios or values. Values can also be determined through finite-difference approximation.

Adiabatic process

This ratio gives the important relation for an isentropic process of a simple compressible calorically-perfect ideal gas:
Using the ideal gas law, :
where is pressure in Pa, is the volume of the gas in and is the temperature in K.
In gas dynamics we are interested in the local relations between pressure, density and temperature, rather than considering a fixed quantity of gas. By considering the density as the inverse of the volume for a unit mass, we can take in these relations.
Since for constant entropy,, we have, or, it follows that
For an imperfect or non-ideal gas, Chandrasekhar defined three different adiabatic indices so that the adiabatic relations can be written in the same form as above; these are used in the theory of stellar structure:
All of these are equal to in the case of a perfect gas.