History of the floppy disk


A floppy disk is a disk storage medium composed of a disk of thin and flexible magnetic storage medium encased in a rectangular plastic carrier. It is read and written using a floppy disk drive. Floppy disks were an almost universal data format from the late 1970s into the 1990s, used for primary data storage as well as for backup and data transfers between computers.
Work on a drive that led to the world's first floppy disk and disk drive began in 1967 at a San Jose IBM facility, and introduced into the market in an 8-inch format in 1972. The more conveniently sized -inch disks were introduced in 1976, and became almost universal on dedicated word processing systems and personal computers. This format was more slowly replaced by the -inch format, first introduced in 1982. There was a significant period where both were popular. A number of other variant sizes were introduced over time, with limited market success.
Floppy disks remained a popular medium for nearly 40 years, but their use was declining by the mid- to late 1990s. The introduction of high speed computer networking and formats based on the new NAND flash technique led to the eventual disappearance of the floppy disk as a standard feature of microcomputers, with a notable point in this conversion being the introduction of the floppy-less iMac in 1998. After 2000, floppy disks were increasingly rare and used primarily with older hardware and especially with legacy industrial computer equipment.

The 8-inch disk

In 1967, IBM tasked their San Jose, California development laboratory to develop a reliable and inexpensive system for loading microcode into their System/370 mainframes in a process called Initial Control Program Load. The System/370 was IBM's first computer system family to make extensive usage of volatile read/write semiconductor memory for microcode, so for most models, whenever the power was turned on, the microcode had to be loaded. IBM also wanted inexpensive media that could be sent out to customers with software updates.
IBM Direct Access Storage Product Manager, Alan Shugart, assigned the job to David L. Noble, who tried to develop a new-style tape for the purpose, but without success. The project was reassigned to Donald L. Wartner, 23FD Disk Drive manager, and Herbert E. Thompson, 23FD Disk manager, along with design engineers Warren L. Dalziel, Jay Brent Nilson, and Ralph Flores; and that team developed the IBM 23FD Floppy Disk Drive System. The disk is a read-only, flexible diskette called the "memory disk" and holding 80 kilobytes of data. Initially the disk was bare, but dirt became a serious problem so they enclosed it in a plastic envelope lined with fabric that would remove dust particles. The Floppy Disk Patent #3,668,658 was issued on June 6, 1972 with named inventors Ralph Flores and Herbert E. Thompson. The Floppy Disk Drive Patent #3,678,481 was issued July 18, 1972 with named inventors Warren L. Dalziel, Jay. B. Nilson, and Donald L. Wartner. IBM introduced the diskette commercially in 1971.
The new device first shipped in 1971 as the 23FD, the program load component of the 2835 Storage Control Unit. and then as a standard part of most System 370 processing units and other IBM products. Internally IBM used another device, code named Mackerel, to write boot disks for distribution to the field.
Alan Shugart left IBM and moved to Memorex where his team shipped the Memorex 650 in 1972, the first commercially available read-write floppy disk drive. The 650 had a data capacity of 175 kB, with 50 tracks, 8 sectors per track, and 448 bytes per sector. The Memorex disk was "hard-sectored", that is, it contained 8 sector holes at the outer diameter to synchronize the beginning of each data sector and the beginning of a track. Most early 8" disks were hard-sectored, meaning that they had a fixed number of disk sectors, marked by physical holes punched around the disk hub, and the drive required the correct media type for its controller.
In 1973, Shugart founded Shugart Associates which went on to become the dominant manufacturer of 8-inch floppy disk drives. Its SA800 became the industry standard for form factor and interface.
In May 1973, IBM shipped its first read/write floppy disk drive, the 33FD, as a component of the 3740 Data Entry System, code named "IGAR", designed to directly replace IBM's punched card data entry machines. The medium sold separately as "Diskette 1" featured the use of a Teflon-lubricated fabric liner to lengthen media life. In 1976, media supplier Information Terminals Corporation enhanced resilience further by adding a Teflon coating to the magnetic disk itself. The new system used a soft sector recording format that stored up to kB on the same disks; the disk was divided into 77 tracks of 26 sectors, each holding 128 bytes. Drives supporting this format were offered by a number of manufacturers and soon became common for moving smaller amounts of data. This disk format became known as the Single Sided Single Density or SSSD format. It was designed to hold just as much data as one box of 2000 punch cards.
When the first microcomputers were being developed in the 1970s, the 8-inch floppy found a place on them as one of the few "high speed, mass storage" devices that were even remotely affordable to the target market. The first microcomputer operating system, CP/M, originally shipped on 8-inch disks. However, the drives were still expensive, typically costing more than the computer they were attached to in early days, so most machines of the era used cassette tape instead.
In 1976, IBM introduced the 500 KB Double Sided Single Density format, and in 1977 IBM introduced the 1–1.2 MB Double Sided Double Density format.
Other 8-inch floppy disk formats such as the Burroughs 1 MB unit failed to achieve any market presence.
At the end of 1978 the typical floppy disk price per piece was $5 to $8. Sales in 1978 for all types of drives and media were expected to reach $135 million for media and $875 million for drives.
The 8" floppy disk drive interface standard as developed from the Shugart Associates drives involved a 50-pin interface and a spindle motor that ran directly from the A/C line and spun constantly. Other later models used a DC motor with corresponding changes to the interface to start and stop the motor.

The -inch minifloppy

In a 1976 meeting, An Wang of Wang Laboratories informed Jim Adkisson and Don Massaro of Shugart Associates that the 8-inch format was simply too large and expensive for the desktop word processing machines he was developing at the time, and argued for a US$100 drive.
According to Massaro, Adkisson proposed a smaller size and began working with cardboard mockups before the Wang meeting. George Sollman suggests the size was the average of existing tape drives of the era. It is an urban legend that the physical size came about when they met with Wang at a bar in Boston; when he was asked what size would be appropriate, Wang pointed to a cocktail napkin—there was no such meeting.
The new drive of this size stored 98.5 KB, later increased to 110 KB by adding five tracks.
The drive was considerably less expensive than 8-inch drives, and soon started appearing on CP/M machines.
Shugart's initial 5.25" drive was the 35-track, single-sided SA-400, which was widely used in many early microcomputers, and which introduced the 34-pin interface that would become an industry standard. It could be used with either a hard- or soft-sectored controller, and storage capacity was listed as 90k or 113k. The drive went on sale in late 1976 at a list price of $400, with a box of ten disks at $60. The new, smaller disk format was taken up quickly, and by 1978 ten different manufacturers were producing 5.25" drives. At one point, Shugart was producing 4,000 drives a day, but their ascendancy was short-lived; the company's fortunes declined in the early 1980s. Part of this was due to their failure to develop a reliable 80-track drive, increasing competition, and the loss of several lucrative contracts—Apple by 1982 had switched to using cheaper Alps drive mechanisms in their computers, and IBM chose Tandon as their sole supplier of disk drives for the PC. By 1977 Shugart had been purchased by Xerox, who closed the operations in 1985 and sold the brand to a third party.
In 1978 I.T.C., had approximately 35 percent of the estimated $135 million floppy disk market and sold 5.25 disks in large quantities for $1.50 each.
Apple purchased bare SA-400 drive mechanisms for their Disk II drive, which was then equipped with a custom Apple controller board and the faceplate stamped with the Apple logo. Steve Wozniak developed a recording scheme known as Group Code Record which allowed 140k of storage, well above the standard 90–113k, although the price of double density controllers fell not long after the Disk II's introduction. GCR recording used software means of detecting the track and sector being accessed, hence there was no need of hard sectored disks or even the index hole.
Commodore also elected to use GCR recording in their disk drive line. Tandy however used industry-standard FM on the TRS-80's disk drives, with stock Shugart SA-400s, and so had a mere 85k of storage.
These early drives read only one side of the disk, leading to the popular budget approach of cutting a second write-enable slot and index hole into the carrier envelope and flipping it over to use the other side for additional storage. This was considered risky by some as single sided disks were only certified by the manufacturer for single-sided use. The reasoning was that, when flipped, the disk would spin in the opposite direction inside its cover, so some of the dirt that had been collected by the fabric lining in the previous rotations would be picked up by the disk and dragged past the read/write head.
Although hard sectored disks were used on some early 8" drives prior to the IBM 33FD, they were never widely used in 5.25" form, although North Star clung to the format until they went bankrupt in 1984.
Tandon introduced a double-sided drive in 1978, doubling the capacity, and this new “double sided double density” format increased capacity to 360 KB..
By 1979, there were also 77-track 5.25" drives available, mostly used in CP/M and other professional computers, and also found in some of Commodore's disk drive line.
By the early 1980s, falling prices of computer hardware and technological advances led to the near-universal adoption of soft-sector, double density disk formats. In addition, more compact half-height disk drives began to appear, as well as double-sided drives, although the cost of them meant that single-sided remained the standard for most home computers, and 80-track drives known as "quad density".
For most of the 1970s and 1980s, the floppy drive was the primary storage device for word processors and microcomputers. Since these machines had no hard drive, the OS was usually booted from one floppy disk, which was then removed and replaced by another one containing the application. Some machines using two disk drives allowed the user to leave the OS disk in place and simply change the application disks as needed, or to copy data from one floppy to another. In the early 1980s, “quad density” 96-track-per-inch drives appeared, increasing the capacity to 720 KB. RX50 was another proprietary format, used by Digital Equipment Corporation's Rainbow-100, DECmate-II, and Pro-350. It held 400 KB on a single side by using 96 tracks per inch and cramming 10 sectors per track.
Floppy disks were supported on IBM's PC DOS and Microsoft's MS-DOS from their beginning on the original IBM PC. With version 1.0 of PC DOS, only single-sided 160 KB floppies were supported. Version 1.1 the next year saw support expand to double-sided 320 KB disks. Finally, in 1983, DOS 2.0 supported 9 sectors per track rather than 8, providing 180 KB on a single-sided disk and 360 KB on a double-sided.
In 1984, IBM introduced the 5.25" high density disk format with its new IBM AT machines. The 5.25" HD drive was essentially a scaled-down 8" drive, using the same rotation speed and bit rate, and it provided almost three times as much storage as the 360k format, but had compatibility issues with the older drives due to the narrower read/write head.
Except for labeling, -inch high-density disks were externally identical to their double-density counterparts. This led to an odd situation wherein the drive itself was unable to determine the density of the disk inserted except by reading the disk media to determine the format. It was therefore possible to use a high-density drive to format a double-density disk to the higher capacity. This usually appeared to work —at least for a time. The problem was that the high-density format was made possible by the creation of a new high-coercivity oxide coating. In order to format or write to this high-coercivity media, the high-density drive switched its heads into a mode using a stronger magnetic field. When these stronger fields were written onto a double-density disk, the strongly magnetized oxide particles would begin to affect the magnetic charge of adjacent particles. The net effect is that the disk would begin to erase itself. On the other hand, the opposite procedure would fail almost every time, as the high-coercivity media would not retain data written by the low-power DD field. High-density -inch disks avoided this problem by the addition of a hole in the disk cartridge so that the drive could determine the appropriate density. However, the coercivity rating between the -inch DD and HD formats, 665 and 720 oersteds, is much narrower than that for the -inch format, 600 versus 300 oersteds, and consequently it was possible to format a -inch DD disk as HD with no apparent problems.
By the end of the 1980s, the -inch disks had been superseded by the -inch disks. Though -inch drives were still available, as were disks, they faded in popularity as the 1990s began. The main community of users was primarily those who still owned 1980s legacy machines that had no -inch drive; the advent of Windows 95 and subsequent phaseout of stand-alone MS-DOS with version 6.22 forced many of them to upgrade their hardware. On most new computers, the -inch drives were optional equipment. By the mid-1990s, the drives had virtually disappeared as the -inch disk became the predominant floppy disk.

The "Twiggy" disk

During the development of the Apple Lisa, Apple developed a disk format codenamed Twiggy, and officially known as FileWare. While basically similar to a standard -inch disk, the Twiggy disk had an additional set of write windows on the top of the disk with the label running down the side. The drive was also present in prototypes of the original Apple Macintosh computer, but was removed in both the Mac and later versions of the Lisa in favor of the -inch floppy disk from Sony. The drives were notoriously unreliable and Apple was criticized for needlessly diverging from industry standards.

The 3-inch compact floppy disk

Throughout the early 1980s, the limitations of the -inch format were starting to become clear. Originally designed to be smaller and more practical than the 8-inch format, the -inch system was itself too large, and as the quality of the recording media grew, the same amount of data could be placed on a smaller surface. Another problem was that the -inch disks were simply scaled down versions of the 8-inch disks, which had never really been engineered for ease of use. The thin folded-plastic shell allowed the disk to be easily damaged through bending, and allowed dirt to get onto the disk surface through the opening.
A number of solutions were developed, with drives at 2-inch, -inch, 3-inch and -inch, all being offered by various companies. They all shared a number of advantages over the older format, including a small form factor and a rigid case with a slideable write protect catch. The almost-universal use of the -inch format made it very difficult for any of these new formats to gain any significant market share. Some of these formats included Dysan and Shugart's -inch floppy disk, the later ubiquitous Sony -inch disk and the 3-inch format:
The 3-inch floppy drive itself was manufactured by Hitachi, Matsushita and Maxell. Only Teac outside this "network" is known to have produced drives. Similarly, only three manufacturers of media are known, but "no-name" disks with questionable quality have been seen in circulation.
Amstrad included a 3-inch single-sided, double-density drive in their CPC and some models of PCW. The PCW 8512 included a double-sided, quad-density drive as the second drive, and later models, such as the PCW 9512, used quad-density even for the first drive. The single-sided double density drive was "inherited" by the ZX Spectrum +3 computer after Amstrad bought the rights from Sinclair. The Oric-1 and Atmos systems from Oric International also used the 3-inch floppy drives, originally shipping with the Atmos, but also supported on the older Oric-1.
Since all 3-inch media were double-sided in nature, single-sided drive owners were able to flip the disk over to use the other side. The sides were termed "A" and "B" and were completely independent, but single-sided drive units could only access the upper side at one time.
The disk format itself had no more capacity than the more popular -inch floppies. Each side of a double-density disk held 180 KB for a total of 360 KB per disk, and 720 KB for quad-density disks. Unlike -inch or -inch disks, the 3-inch disks were designed to be reversible and sported two independent write-protect switches. It was also more reliable thanks to its hard casing.
3-inch drives were also used on a number of exotic and obscure CP/M systems such as the Tatung Einstein and occasionally on MSX systems in some regions. Other computers to have used this format are the more unknown Gavilan Mobile Computer and Matsushita's National Mybrain 3000. The Yamaha MDR-1 also used 3-inch drives.
The main problems with this format were the high price, due to the quite elaborate and complex case mechanisms. However, the tip on the weight was when Sony in 1984 convinced Apple Computer to use the -inch drives in the Macintosh 128K model, effectively making the -inch drive a de facto standard.

Mitsumi's "Quick Disk" 3-inch floppies

Another 3-inch format was Mitsumi's Quick Disk format. The Quick Disk format is referred to in various size references: 2.8-inch, 3-inch×3-inch and 3-inch×4-inch. Mitsumi offered this as OEM equipment, expecting their VAR customers to customize the packaging for their own particular use; disks thus vary in storage capacity and casing size. The Quick Disk uses a 2.8-inch magnetic media, break-off write-protection tabs, and contains a see-through hole near center spindle. Nintendo packaged the 2.8-inch magnetic media in a 3-inch×4-inch housing, while others packaged the same media in a 3 inch×3 inch square housing.
The Quick Disk's most successful use was in Nintendo's Famicom Disk System. The FDS package of Mitsumi's Quick Disk used a 3-inch×4-inch plastic housing called the "Disk System Card". Most FDS disks did not have cover protection to prevent media contamination, but a later special series of five games did include a protective shutter.
Mitsumi's "3-inch" Quick Disk media were also used in a 3-inch×3-inch housing for many Smith Corona word processors. The Smith Corona disks are confusingly labeled "DataDisk 2.8-inch", presumably referring to the size of the medium inside the hard plastic case.
The Quick Disk was also used in several MIDI keyboards and MIDI samplers of the mid-1980s. A non-inclusive list includes: the Roland S-10 and MKS100 samplers, the Korg SQD1, the Korg SQD8 MIDI sequencer, Akai's 1985 model MD280 drive for the S-612 MIDI sampler, Akai's X7000 / S700 and X3700, the Roland S-220, and the Yamaha MDF1 MIDI disk drive.
As the cost in the 1980s to add -inch drives was still quite high, the Mitsumi Quick Disk was competing as a lower cost alternative packaged in several now obscure 8-bit computer systems. Another non-inclusive list of Quick Disk versions: QDM-01, QDD on French Thomson micro-computers, in the Casio QD-7 drive, in a peripheral for the Sharp MZ-700 & MZ-800 system, in the DPQ-280 Quickdisk for the Daewoo/Dynadata MSX1 DPC-200, in the Dragon 32/64 machine, in the Crescent Quick Disk 128, 128i and 256 peripherals for the ZX Spectrum, and in the Triton Quick Disk peripheral also for the ZX Spectrum.
The World of Spectrum FAQ reveals that the drives did come in different sizes: 128 to 256 kB in Crescent's incarnation, and in the Triton system, with a density of 4410 bits per inch, data transmission rate of 101.6 kbit/s, a 2.8-inch double sided disk type and a capacity of up to 20 sectors per side at 2.5 kB per sector, up to 100 kB per disk. Quick Disk as used in the Famicom Disk System holds 64 kB of data per side, requiring a manual turn-over to access the second side.
Unusually, the Quick Disk utilizes "a continuous linear tracking of the head and thus creates a single spiral track along the disk similar to a record groove." This has led some to compare it more to a "tape-stream" unit than typically what is thought of as a random-access disk drive.

-inch format

In 1981, Sony introduced their -inch floppy disk cartridge having a single sided unformatted capacity of 218.8 KB and a formatted capacity of 161.2 KB. A double sided version was available in 1982. This initial Sony design was similar to other less than -inch designs but somewhat simpler in construction. The first computer to use this format was Sony's SMC 70 of 1982. Other than Hewlett-Packard's HP-150 of 1983 and Sony's MSX computers that year, this format suffered from a similar fate as the other new formats; the -inch format simply had too much market share.
Things changed dramatically in 1982 when the Microfloppy Industry Committee, a consortium ultimately of 23 media companies, agreed upon a -inch media specification based upon but differing from the original Sony design. The first single-sided drives compatible with this new media specification shipped in early 1983, followed immediately in 1984 by double-sided compatible versions. In 1984, Apple Computer selected the format for their new Macintosh computers. Then, in 1985, Atari adopted it for their new ST line, and Commodore for their new Amiga. By 1988, the -inch was outselling the -inch. In South Africa, the -inch format was generally called a stiffy disk, to distinguish it from the flexible 5½-inch format.
The term "-inch" or "3.5-inch" disk is and was rounded from the 90 mm actual dimension of one side of the rectangular cartridge. The actual disk diameter is.
The -inch disks had, by way of their rigid case's slide-in-place metal cover, the significant advantage of being much better protected against unintended physical contact with the disk surface than -inch disks when the disk was handled outside the disk drive. When the disk was inserted, a part inside the drive moved the metal cover aside, giving the drive's read/write heads the necessary access to the magnetic recording surfaces. Adding the slide mechanism resulted in a slight departure from the previous square outline. The irregular, rectangular shape had the additional merit that it made it impossible to insert the disk sideways by mistake as had indeed been possible with earlier formats.
3.5" drives included several other advantages over the older drive types, including not requiring a terminating resistor pack, and no need of an index hole.
The shutter mechanism was not without its problems, however. On old or roughly treated disks, the shutter could bend away from the disk. This made it vulnerable to being ripped off completely, or worse, catching inside a drive and possibly either getting stuck inside or damaging the drive.

Evolution

Like the -inch, the -inch disk underwent an evolution of its own. When Apple introduced the Macintosh in 1984, it used single-sided -inch disk drives with an advertised capacity of 400 kB. The encoding technique used by these drives was known as GCR, or Group Coded Recording.
;Higher capacities
Somewhat later, PC-compatible machines began using single-sided -inch disks with an advertised capacity of 360 kB, and a different, incompatible recording format called MFM. GCR and MFM drives were incompatible, although the physical disks were the same. In 1986, Apple introduced double-sided, 800 kB disks, still using GCR, and soon after, IBM began using 720 kB double-sided double-density MFM disks in PCs like the IBM PC Convertible. IBM PC compatibles adopted it too, while the Amiga used MFM encoding on the same disks to give a capacity of 1 MB.
;HD
An MFM-based, "high-density" format, displayed as "HD" on the disks themselves and typically advertised as "1.44 MB" was introduced in 1987; the most common formatted capacity was 1,474,560 bytes. These HD disks had an extra hole in the case on the opposite side of the write-protect notch. IBM used this format on their PS/2 series introduced in 1987. Apple started using "HD" in 1988, on the Macintosh IIx, and the HD floppy drive soon became universal on virtually all Macintosh and PC hardware. Apple's FDHD drive was capable of reading and writing both GCR and MFM formatted disks, and thus made it relatively easy to exchange files with PC users. Apple later marketed this drive as the SuperDrive. Amiga included "HD" floppy drives relatively late, with releasing of Amiga 4000 in 1992, and was able to store 1760 KB on it, with ability in software to read/write PC's 1440 KB/720 KB formats.
;ED
Another advance in the oxide coatings allowed for a new "extra-high density" format at 2880 KB introduced on the NeXTcube, NeXTstation and IBM PS/2 model 57. However, by this time the increased capacity was too small an advance over the HD format and it never became widely used.