Moment distribution method
The moment distribution method is a structural analysis method for statically indeterminate beams and frames developed by Hardy Cross. It was published in 1930 in an ASCE journal. The method only accounts for flexural effects and ignores axial and shear effects. From the 1930s until computers began to be widely used in the design and analysis of structures, the moment distribution method was the most widely practiced method.
Introduction
In the moment distribution method, every joint of the structure to be analysed is fixed so as to develop the fixed-end moments. Then each fixed joint is sequentially released and the fixed-end moments are distributed to adjacent members until equilibrium is achieved. The moment distribution method in mathematical terms can be demonstrated as the process of solving a set of simultaneous equations by means of iteration.The moment distribution method falls into the category of displacement method of structural analysis.
Implementation
In order to apply the moment distribution method to analyse a structure, the following things must be considered.Fixed end moments
are the moments produced at member ends by external loads.Bending stiffness
The bending stiffness of a member is represented as the flexural rigidity of the member and the second moment of area ) divided by the length of the member. What is needed in the moment distribution method is not the specific values but the ratios of bending stiffnesses between all members.Distribution factors
When a joint is being released and begins to rotate under the unbalanced moment, resisting forces develop at each member framed together at the joint. Although the total resistance is equal to the unbalanced moment, the magnitudes of resisting forces developed at each member differ by the members' bending stiffness. Distribution factors can be defined as the proportions of the unbalanced moments carried by each of the members. In mathematical terms, the distribution factor of member framed at joint is given as:where n is the number of members framed at the joint.
Carryover factors
When a joint is released, balancing moment occurs to counterbalance the unbalanced moment. The balancing moment is initially the same as the fixed-end moment. This balancing moment is then carried over to the member's other end. The ratio of the carried-over moment at the other end to the fixed-end moment of the initial end is the carryover factor.Determination of carryover factors
Let one end of a fixed beam be released and applied a moment while the other end remains fixed. This will cause end A to rotate through an angle. Once the magnitude of developed at end B is found, the carryover factor of this member is given as the ratio of over :In case of a beam of length L with constant cross-section whose flexural rigidity is,
therefore the carryover factor
Sign convention
Once a sign convention has been chosen, it has to be maintained for the whole structure. The traditional engineer's sign convention is not used in the calculations of the moment distribution method although the results can be expressed in the conventional way. In the BMD case, the left side moment is clockwise direction and other is anticlockwise direction so the bending is positive and is called sagging.Framed structures
Framed structures with or without sidesway can be analysed using the moment distribution method.Example
The statically indeterminate beam shown in the figure is to be analysed.The beam is considered to be three separate members, AB, BC, and CD, connected by fixed end joints at B and C.
- Members AB, BC, CD have the same span.
- Flexural rigidities are EI, 2EI, EI respectively.
- Concentrated load of magnitude acts at a distance from the support A.
- Uniform load of intensity acts on BC.
- Member CD is loaded at its midspan with a concentrated load of magnitude.
Fixed end moments
Bending stiffness and distribution factors
The bending stiffness of members AB, BC and CD are, and, respectively. Therefore, expressing the results in repeating decimal notation:The distribution factors of joints A and D are and.
Carryover factors
The carryover factors are, except for the carryover factor from D to C which is zero.Moment distribution
Numbers in grey are balanced moments; arrows represent the carry-over of moment from one end to the other end of a member.* Step 1: As joint A is released, balancing moment of magnitude equal to the fixed end moment develops and is carried-over from joint A to joint B.* Step 2: The unbalanced moment at joint B now is the summation of the fixed end moments, and the carry-over moment from joint A. This unbalanced moment is distributed to members BA and BC in accordance with the distribution factors and. Step 2 ends with carry-over of balanced moment to joint C. Joint A is a roller support which has no rotational restraint, so moment carryover from joint B to joint A is zero.* Step 3: The unbalanced moment at joint C now is the summation of the fixed end moments, and the carryover moment from joint B. As in the previous step, this unbalanced moment is distributed to each member and then carried over to joint D and back to joint B. Joint D is a fixed support and carried-over moments to this joint will not be distributed nor be carried over to joint C.* Step 4: Joint B still has balanced moment which was carried over from joint C in step 3. Joint B is released once again to induce moment distribution and to achieve equilibrium.* Steps 5 - 10: Joints are released and fixed again until every joint has unbalanced moments of size zero or neglectably small in required precision. Arithmetically summing all moments in each respective columns gives the final moment values.Result
- Moments at joints determined by the moment distribution method
- Moments at joints determined by the matrix method
Result via displacements method
As the Hardy Cross method provides only approximate results, with a margin of error inversely proportionate to the number of iterations, it is important to have an idea of how accurate this method might be. With this in mind, here is the result obtained by using an exact method: the displacement methodFor this, the displacements method equation assumes the following form:
For the structure described in this example, the stiffness matrix is as follows:
The equivalent nodal force vector:
Replacing the values presented above in the equation and solving it for leads to the following result:
Hence, the moments evaluated in node B are as follows:
The moments evaluated in node C are as follows: