Package cushioning


Package cushioning is used to protect items during shipment. Vibration and impact shock during shipment and loading/unloading are controlled by cushioning to reduce the chance of product damage.
Cushioning is usually inside a shipping container such as a corrugated box. It is designed to absorb shock by crushing and deforming, and to dampen vibration, rather than transmitting the shock and vibration to the protected item. Depending on the specific situation, package cushioning is often between 50 and 75 millimeters thick.
Internal packaging materials are also used for functions other than cushioning, such as to immobilize the products in the box and lock them in place, or to fill a void.
cushioning

Design factors

When designing packaging the choice of cushioning depends on many factors, including but not limited to:
Loose fill –
Some cushion products are flowable and are packed loosely around the items in the box. The box is closed to tighten the pack. This includes expanded polystyrene foam pieces, similar pieces made of starch-based foams, and common popcorn. The amount of loose fill material required and the transmitted shock levels vary with the specific type of material.
Paper –
Paper can be manually or mechanically wadded up and used as a cushioning material. Heavier grades of paper provide more weight-bearing ability than old newspapers. Creped cellulose wadding is also available.
Corrugated fiberboard pads –
Multi-layer or cut-and-folded shapes of corrugated board can be used as cushions. These structures are designed to crush and deform under shock stress and provide some degree of cushioning. Paperboard composite honeycomb structures are also used for cushioning.
Foam structures –
Several types of polymeric foams are used for cushioning. The most common are: Expanded Polystyrene, polypropylene, polyethylene, and polyurethane. These can be molded engineered shapes or sheets which are cut and glued into cushion structures. Convoluted foams sometimes used. Some degradable foams are also available.
Foam-in-place is another method of using polyurethane foams. These fill the box, fully encapsulating the product to immobilize it. It is also used to form engineered structures.
Molded pulp –
Pulp can be molded into shapes suitable for cushioning and for immobilizing products in a package. Molded pulp is made from recycled newsprint and is recyclable.
Inflated products –
Bubble wrap consists of sheets of plastic film with enclosed “bubbles” of air. These sheets can be layered or wrapped around items to be shipped. A variety of engineered inflatable air cushions are also available. Note that inflated air pillows used for void-fill are not suited for cushioning.
Other –
Several other types of cushioning are available including suspension cushions, thermoformed end caps
, and various types of shock mounts.

Design for shock protection

Proper performance of cushioning is dependent on its proper design and use. It is often best to use a trained packaging engineer, reputable vendor, consultant, or independent laboratory.
An engineer needs to know the severity of shock to protect against. This can be based on an existing specification, published industry standards and publications, field studies, etc.
Knowledge of the product to be packaged is critical. Field experience may indicate the types of damage previously experienced. Laboratory analysis can help quantify the fragility of the item, often reported in g's. Engineering judgment can also be an excellent starting point. Sometimes a product can be made more rugged or can be supported to make it less susceptible to breakage.
The amount of shock transmitted by a particular cushioning material is largely dependent on the thickness of the cushion, the drop height, and the load-bearing area of the cushion. A cushion must deform under shock for it to function. If a product is on a large load-bearing area, the cushion may not deform and will not cushion the shock. If the load-bearing area is too small, the product may “bottom out” during a shock; the shock is not cushioned. Engineers use “cushion curves” to choose the best thickness and load-bearing area for a cushioning material. Often two to three inches of cushioning are needed to protect fragile items.
Computer simulations and finite element analysis are also being used. Some correlations to laboratory drop tests have been successful.
Cushion design requires care to prevent shock amplification caused by the cushioned shock pulse duration being close to the natural frequency of the cushioned item.

Design for vibration protection

The process for vibration protection not have any influence on input vibration, 2) amplify the input vibration at resonance, or 3) isolate the product from the vibration. Proper design is critical for cushion performance.

Evaluation of finished package

of prototype designs are required. The design of a package and its cushioning is often an iterative process involving several designs, evaluations, redesigns, etc. Several published package testing protocols are available to evaluate the performance of a proposed package. Field performance should be monitored for feedback into the design process.

ASTM Standards