Potato cannon


A potato cannon is a pipe-based cannon which uses air pressure, or combustion of a flammable gas, to launch projectiles at high speeds. They are built to fire chunks of potato, as a hobby, or to fire other sorts of projectiles, for practical use. Projectiles or failing guns can be dangerous and result in life-threatening injuries, including cranial fractures, enucleation, and blindness if a person is hit.
The potato cannon can trace its origin to the World War II-era Holman Projector, which was a shipboard anti-aircraft weapon.

Launcher types

All spud guns propel projectiles down their barrels using pressurised gas in the same manner as a firearm. There are four basic ways that spud guns may achieve this:
Combustion powered spud guns typically have the least complex designs, the four basic elements of which are:
In order to fire, the operator loads a projectile into the barrel, adds fuel to the combustion chamber, and triggers the ignition source. The fuel then ignites, creating hot expanding gases, and forcing the projectile out of the barrel. Distances vary greatly depending on many factors, including the type of fuel used, the efficiency of the fuel/air ratio, the combustion chamber/barrel ratio, and the flight characteristics of the projectile. Common distances vary from 100 to 200 meters, and there is a reported case of a cannon exceeding 500 meters of range.
Advanced combustion launchers may include metered propane or calcium carbide injection to ensure proper fueling, chamber fans to mix the fuel with the air and accelerate venting of the chamber after firing, multiple spark gaps to decrease combustion time, and high-voltage ignition sources.
Combustion launchers are usually less powerful than their pneumatic or hybrid counterparts, especially when hairspray / alcohol is used as a propellant. Bottled oxygen can be added to the firing chamber, though this can cause an explosion of the pipe when firing, potentially injuring anyone nearby.

Pneumatic launchers

launchers are considered a little more difficult to build due to the need of a completely airtight construction. These cannons have four basic components:
In a pneumatic spud gun, air is pumped into the pressure chamber. After the desired chamber pressure is reached, the pressure release valve is opened, allowing the gas to expand down the barrel, propelling the projectile forwards.
The filling valve is usually a commonly available type such as a Schrader or Presta valve but other assemblies to pressurise the cannon such as quick release connections with ball or check valves have been used.
The pressure release valve is often one of a variety of commercially available types such as a plumbing ball valve, an irrigation sprinkler valve or a quick exhaust valve. Experienced builders often make their own valves for this purpose to gain greater flow and faster actuation. The most common custom design used is the piston valve. Multiple valves arranged to be triggered together are occasionally used as an alternative to a single larger valve.
The range of pneumatic cannons is more variable than the range of combustion spud guns due to the increased variation possible in the components. Typical ranges are slightly higher because of the greater power, but the maximum range of some high power pneumatic cannons has been said to be over.
Pneumatic spud guns are generally more powerful than combustion spud guns. A typical combustion gun generates average chamber pressures of about with peaks of around, while the average pneumatic gun can operate at pressures in the vicinity of. In recent times, it has become increasingly common for metal pneumatic launchers to use even higher pressures, sometimes up to or higher.

Dry ice launchers

A dry ice cannon uses the sublimation of solid carbon dioxide to generate the gas pressure to propel a projectile and is a variation of the burst disk cannon.
The oldest examples simply involve dropping pieces of dry ice into a tube closed at one end and sealing the other end by jamming the projectile in. When the pressure of the carbon dioxide from the subliming dry ice builds high enough, the projectile will be blown out of the tube. The pressures of such devices are not very high as it only needs to build enough to overcome the static friction of the projectile jammed in the barrel. Tens of psi is most likely. The range is likely restricted to 100- yards.
A more modern example is the dry ice bomb launcher. A plastic bottle containing water has some dry ice added and is quickly sealed and dropped down a tube closed at one end. A projectile is inserted in after it. The water accelerates the sublimation of the dry ice and the pressure from the carbon dioxide gas produced eventually ruptures the plastic bottle and launches the projectile. The rupturing pressure of a 0.5 L plastic soda bottle is between in the open air but when confined in a pipe, it could be higher.
Due to the operation of a dry ice bomb cannon extra safety issues are present:
Compared to the operation of other spud guns, dry ice bomb cannons are similar in firing principle to a light-gas gun of the pneumatic type; the plastic bottle performing the task of the burst disk albeit in a less controlled manner.
Another means of utilising dry ice in spud guns is to use the sublimation of dry ice to create substantial pressure behind a valve, and placing a barrel on the other side of that valve with a projectile loaded into it. Pressures behind the valve can reach upwards of, and by quickly releasing the valve, the projectile can be launched. Whilst this method is more controllable and in many means safer than utilising a soda bottle as a burst disk, it is limited in that quick release valves, such as ball valves, are generally not bigger in diameter than 1 or 2 inches. Additionally, they cannot be opened as rapidly as a soda bottle will rupture, and consequently there is less immediate airflow. However, this is offset by the fact that such a design can operate at more than double the pressure of a typical dry ice bomb launcher, as soda bottles will rupture at only.

Hybrid launchers

A hybrid launcher consists of seven basic elements:
A hybrid combines principles of the combustion and pneumatic spud gun. It uses a pre-pressurised mixture of fuel and air to get more power out of a given chamber volume.
In order to fire, the operator first readies the pressure-triggered valve then injects several times the normal amount of fuel and appropriately more air. When the ignition source is triggered, the pressure from the combustion causes the main valve to open and propels the projectile out of the barrel with the released combustion gases. The hybrid is capable of higher velocities than a combustion or pneumatic spud gun because the pressure generated is higher than that in a combustion gun, and the shock wave moves faster than it can in a pneumatic, due to the higher temperature. Projectiles fired by a hybrid have broken the sound barrier.
A hybrid using a fuel and air mix at twice atmospheric pressure is said to be using a 2X mix. Higher mixtures can be used and will produce even higher pressures. The fuel and air needs to be measured and matched carefully to ensure reliable operation; hence the use of accurate air pressure gauges and fuel meters.

Vacuum cannons

Vacuum cannons differ from typical pneumatic cannons in that they apply a negative pressure to the front of the projectile in order to "pull" it out of the barrel. They typically fire light projectiles and do not have any practical applications outside of demonstrating air pressure theory.

Primary materials

Plastics

Both PVC and ABS piping are also available in forms which are not pressure rated. Use of unrated plastic piping and fittings is a common source of cannon failure and poses a much greater risk to a cannon operator.

Metals

Manual

Welding, soldering and gluing

It is rare for a spud gun to be powerful enough to break the sound barrier, although there are some cases of this happening using specialized designs. The spud guns used are typically hybrids; but some pneumatic cannons have achieved the feat, either by using a special low-density gas, such as helium, or high pressures combined with a fast valve. There is also one reported case of a combustion design achieving super-sonic velocities.
The difficulty in breaking the barrier arises from the speed of the particles within the gas. The projectile cannot travel faster than the gas particles, which are limited to travel at the speed of sound. The problem is solved by increasing the speed of the particles, either by:
Supersonic velocities may theoretically be attained by pneumatics with a sufficiently large "dead space" between the main valve and projectile. The incoming air can raise the pressure rapidly in this dead space, creating high temperatures sometimes sufficient to achieve supersonic velocities. This particular effect has not yet been successfully used, but has been discussed, as both adiabatic and shock heating are documented phenomena in gases.
The highest projectile speed recorded from a spud gun is with a 20 mm plastic slug from a hybrid using a pre-ignition mixture of air and propane.
Supersonic velocities have been obtained using the related vacuum bazooka with a de Laval nozzle. This also relies on significantly lowering the density of the gas.

Practical uses

Although spudguns are created and used for the purpose of recreation there are other devices which work on identical principles in many other fields with more serious uses.

Entertainment

Spud guns by nature are hazardous and can present safety issues if poorly constructed or used.
Users should follow the same rules as if handling a conventional firearm, but given the frequently improvised materials and construction used in spudguns, it is particularly important for the user to use basic ear and eye protection when operating a spudgun.

Legal issues

In some jurisdictions spud guns are outlawed or have restrictions on their use and may require licenses and certification of the gun.

In popular culture