Prusik


A Prusik is a friction hitch or knot used to attach a loop of cord around a rope, applied in climbing, canyoneering, mountaineering, caving, rope rescue, ziplining, and by arborists. The term Prusik is a name for both the loops of cord and the hitch, and the verb is "to prusik". More casually, the term is used for any friction hitch or device that can grab a rope. Due to the pronunciation, the word is often misspelled Prussik, Prussick, or Prussic.
The Prusik hitch is named after its putative inventor, Austrian mountaineer Karl Prusik. It was shown in a 1931 Austrian mountaineering manual for rope ascending. It was used on several mountaineering routes of the era to ascend the final summit, where a rope could be thrown over the top and anchored so that climbers could attain the summit by prusiking up the other side of the rope.
A prusik made from cord does little or no damage to the rope it is attached to, although some mechanical prusiks can cause damage, especially if the device slips during climbing.

Advantages

Climbers carry Prusik cords mainly for emergency use, as they are lighter than other options. Prusiks are fast to place on a rope, and with practice can be placed with one hand. The loops of cord can be used as slings, and are thus multi-functional in a climbing environment.
Prusiks will work around two ropes, even two ropes of different diameters. Prusiks provide a strong attachment that will not damage or break the rope, and so are used in some rope-rescue techniques. Prusiks are good to use in hauling systems where multiple rope-grabs may be needed, and where mechanical rope-grabs are not available.
Prusiks are far less likely to damage the main rope than mechanical rope-grabs such as a jumar. A prusik which is overloaded will initially slip, causing no damage. If loaded to great excess, the worst result is that it slides until the heat of friction causes physical failure of the prusik cord, rather than the rope. Mechanical rope-grabs when overloaded will sometimes damage the sheath of the rope, or in extreme cases sever the rope entirely.
Depending on which variant is used, Prusik hitches have the advantage of working in both directions. Most mechanical rope-grabs work like a ratchet, moving freely up the rope, but grabbing when a load is placed down on them. Traditional Prusiks will grab when pulled by the tail, either up or down, and will slide either way when pushed by the barrel.
Although the Prusik Climb technique may be seen as outdated by some, the US Army still includes it in its annual Best Ranger competition. Rangers in the competition routinely make it up a 65-foot rope in under a minute.

Disadvantages

Prusiks are ineffective upon frozen wet ropes. This is due to the necessity of friction for the Prusik to function. Mechanical devices to grab the rope are available that are easier and faster to use, but heavier, more expensive, and bulkier.
After being put under a great deal of weight, the Prusik can be quite constricted and difficult to untie. This varies, depending on the relative diameter of the ropes.

Related hitches and equipment

Although prusik can be used in a general way, the Prusik hitch is a specific hitch. The two main alternatives are the Bachmann knot and the Klemheist knot. Each has its advantages and disadvantages, mainly in how easy they are to use for climbing a rope. Another variation is the Autoblock or French Prusik, used by some people as a backup knot while rappelling.
A Purcell Prusik is a related cord popular among cavers and rope-rescue people. A somewhat longer loop than the normal Prusik is used around the rope, then a second Prusik is used around the cord loop itself to form a foot loop. The foot loop is then easily adjusted in length and position.
A Prusik-Minding-Pulley is common in rope rescue. The rope to be pulled is passed through a pulley, and a Prusik is tied on the loaded side. When the rope is pulled, the Prusik rides against the pulley, and the rope slides through it; but when the rope is relaxed, the Prusik slides away from the pulley and grabs the rope. Thus, the combination acts as a ratchet.
The Farrimond friction hitch is a kind of taut-line hitch that is similar in form to a Prusik.

Equipment

A Prusik loop is made of narrow but strong nylon accessory cord tied into a loop using a double fisherman's knot. A sling or prusik-dedicated sewn loop can also be used. Note that Dyneema/Spectra has a very low melting point and should not be used in Prusik hitches unless the cord or sling is specifically engineered for it. The length of this loop depends on the application. For instance, the loop used for an Auto-Bloc might only be 20 cm, whereas the foot loop for climbing a rope might work better with a length of 100 cm or more. As a general rule, longer loops are preferable over shorter ones, as a loop can always be shortened by tying a knot in it.
The effectiveness of the Prusik hitch relies on the surface area between the hitch and the main line, and the diameter of the cord used. Normally the greater difference between the diameter of the cord used for the hitch and the main line, the greater the ability for the hitch to hold. However, the smaller the diameter of the cord used, the lower its safe working load. In addition, smaller diameter cords often jam too tight when placed under load, and are hard to handle when wearing gloves.

Tying

The Prusik is tied by wrapping the prusik loop around the rope a number of times, usually 3-5 times depending on the materials, and then back through itself, forming a barrel around the rope with a tail hanging out the middle. When the tail is weighted, the turns tighten and make a bend in the rope. When weight is removed, the loop can be moved along the rope by placing a hand directly on the barrel and pushing. Breaking the Prusik free from the rope after it has been weighted can be difficult, however, and is most easily done by pushing the bow, the loop of cord which runs from the top wrap over the knot to the bottom wrap, along the tail a little. This unwinds the wrap to loosen the grip of the hitch, and makes movement easier.
Many materials may be used to tie a prusik. The exemplary prusik knot illustrated above is made with webbing, however webbing is not recommended for heavier loads and/or securing a person since it has been shown to slip. Adding more wraps increases the grip.

Applications

In addition to being a useful rope-grab for rope-rescue applications, Prusiks are popular for:
All sorts of climbers carry prusiks as standard equipment "just in case". Prusiks are unlikely to be needed on short climbs where the climber can be readily lowered to the ground; conversely, they may prove useful where the climber cannot be lowered, for instance from a high cliff or due to a hazard underneath the climber.
Prusiks can be tied using other climbing equipment, such as slings already carried by the climber. Three loops allow the climber to pass a knot in the rope, a difficult task without a third loop.
Kayaking:
For kayaking, a prusik can be used in a similar way as in climbing; for rescuing people and equipment from a river, a prusik or two with a set of pulleys to create a Z-drag is preferred.