Road surface marking


Road surface marking is any kind of device or material that is used on a road surface in order to convey official information; they are commonly placed with road marking machines. They can also be applied in other facilities used by vehicles to mark parking spaces or designate areas for other uses.
Road surface markings are used on paved roadways to provide guidance and information to drivers and pedestrians. Uniformity of the markings is an important factor in minimizing confusion and uncertainty about their meaning, and efforts exist to standardize such markings across borders. However, countries and areas categorize and specify road surface markings in different ways—white lines are called white lines mechanical, non-mechanical, or temporary. They can be used to delineate traffic lanes, inform motorists and pedestrians or serve as noise generators when run across a road, or attempt to wake a sleeping driver when installed in the shoulders of a road. Road surface marking can also indicate regulation for parking and stopping.
There is continuous effort to improve the road marking system, and technological breakthroughs include adding retroreflectivity, increasing longevity, and lowering installation cost.
Today, road markings are used to convey a range of information to the driver spanning navigational, safety and enforcement issues leading to their use in road environment understanding within advanced driver-assistance systems and consideration for future use in autonomous road vehicles.

Mechanical markers

Mechanical devices may be raised or recessed into the road surface, and either reflective or non-reflective. Most are permanent; some are movable.
Sometimes the result of roadwork may leave visible marks on the pavements. An example is the dowel bar retrofit process to reinforce concrete slabs in order to extend the life of older concrete pavements. The completion of the process leaves a symmetrical pattern of dash marks on the roadway, as if there were an associated meaning to the pattern. When there are many of them along the roadway, motorists may interpret the marks as an unknown form of mechanical markers or strange road surface markings. When roads are under construction and the lanes are shifted laterally, those marks may interfere with temporary lane markings. As the marks from the dowel bar retrofit are not intended to be any form of road surface markings, the responsible agencies try to make these marks less visible to the motorists.

Non-mechanical markers

Paint

Paint, sometimes with additives such as retroreflective glass beads, is generally used to mark travel lanes. It is also used to mark spaces in parking lots or special purpose spaces for disabled parking, loading zones, or time-restricted parking areas. colours for these applications vary by locality. Paint is a low-cost marking and has been in widespread use since approximately the early 1950s.
Paint consists of three main components: pigments, resins or binders, and water or solvents. Pigments are finely grounded materials that give out colours or block out the surface beneath it. They may contain other materials such as UV stabilizer, and fillers which bring out the colour pigments to the required level. Resins or binders are the glue of the paint to bind pigment and glass beads together to the road surface. The resins for the water-based paints are polyvinyl acetate latex, methyl methacrylate or acrylic resin. The resins for solvent-based paints are linseed or soya oils and alkyd resins. The pigments and resins are mixed with water for water-based paints and solvents for solvent-based paints so that they can be applied onto the road surface. Solvents that are use can be naphtha, toluene, methanol, methylene chloride, and acetone. Due to environmental concerns, some jurisdictions may have restrictions on solvent-based paints.
Paint is usually applied right after the road has been paved. The road is marked commonly by a truck called a "striper." These trucks contain hundreds of gallons of paint stored in huge drums which sit on the bed. The markings are controlled manually or automatically by the controller who sits on the bed. Paint is run through a series of hoses under air pressure and applied to the roadway surface along with the application of glass beads for retroreflectivity. After application, the paint dries fairly quickly. Sometimes the glass beads are mixed in with the paint and applied together, which is not a recommended method. The usual method is to use a separate gun to spray the glass beads on to the wet paint during the application.
Painted symbols, such as turn-lane arrows or HOV lane markers, are applied manually using stencils. Painted markings usually last 9 to 36 months. There are some water-based paints that can be applied at double the level of thickness of typical latex paints. This technique can extend the life of the markings.

Stones

In roads paved with setts or cobblestones, markings can be made with white blocks or stones, like marble or other light-coloured rocks. This kind of marking is long lasting, but could be slippery in rain or wet conditions unless surfaced with a matte or rough finish.

Thermoplastic

One of the most common types of road marking based on its balance between cost and performance longevity, thermoplastic binder systems are generally based on one of three core chemistries: hydrocarbons, rosin esters or maleic modified rosin esters. Thermoplastic coatings are generally homogeneous dry mixes of binder resins, plasticizers, glass beads, pigments, and fillers. Their use has increased over paints mainly due to the performance benefits of increased durability, retro-reflectivity, and a lack of VOC solvents.
Thermoplastic markings are applied using specially designed vehicles. Usually, thermoplastic marking mode should apply with equipment called a road marking machine to coat traffic lines, and the road paint needs preheating by a device commonly called a preheater. The thermoplastic mix is heated in trucks to before being fed to the application apparatus. This is often a screed box or ribbon gun. Immediately after the thermoplastic has been applied, glass beads are laid onto the hot material so that they embed before the plastic hardens. These beads provide initial retroreflection. As the marking wears during use and the initial beads are lost, the beads mixed with the binder are uncovered, providing long term retroreflectivity. These can be made exceptionally thick to produce a rumble strip effect.
The thermoplastic marking coating sets quickly. The melt adhesion of a synthetic resin makes hot-melt paint adhere strongly to the road surface. in the coating paint increases the coating plasticity, improving the anti-settling, anti-pollution, anti-tarnish. Thermoplastic marking paint is most commonly produced in yellow and white. The white marking paint mainly contains titanium white, zinc oxide, lithopone, while the yellow paint is mainly heat-yellowing lead.
In warm climate areas, the thermoplastic markings can last three to six years. However, snowplows can damage the thermoplastics which would limit the usage in the cold climate areas. The filling materials of road paint can affect the mechanical strength, abrasion resistance and hue of the coating film. The particle size of the paint powder influences the flow, sedimentation, and the surface processing.

Preformed thermoplastic

Preformed thermoplastic pavement markings are thermoplastic cut into the final shapes by the manufacturers and ready to position onto an asphalt or concrete pavement surface. Preformed thermoplastics are put into place on the road surface and applied using a propane heat torch. Some models require heating the road surface prior to the placement of the preformed thermoplastics. These markings are used primarily because of their durability and cost-effective service life. Since the plastics are melted into the surface, they are not easily damaged by the snowplows. Typically, the preformed thermoplastic markings can last 3 to 6 years. The most common applications of preformed thermoplastic pavement markings are found at intersections as transverse markings such as stop lines, legends, crosswalks, arrows, bike lane symbols, and accessibility symbols.

Preformed polymer tape

Commonly referred to as tape or cold plastic, this product is heavy-grade material with reflective beads embedded in the plastic. It is commonly used to mark crosswalks, stop bars, and traffic guidance such as turn lanes, HOV lanes, train crossings, pedestrian crossings, taxi lanes, bus lanes, and bike lanes. There are two ways to apply tape:
The life of the preformed polymer tapes can vary based on the applications. If applied correctly, they can last between 4 and 8 years. However, there have been cases where tape failures start soon after the installation. Conditions that may contribute to the tapes to peel off are the time of year of the installation that is too close to the winter, surface preparation, and workmanship. A technique that can be used to minimize the tape getting scraped off by snowplows is sandblasting a groove into the surface and fixing the tape onto this groove. This technique diminishes the advantage of low labor cost of the tapes.
The preformed polymer tape markings are slippery when wet, especially in large sections such as crosswalks, and caution should be used due to poor wet traction.

Epoxy

contains two parts which are a pigmented resin base and catalyst. The two parts are mixed in a specialized truck for epoxy marking application. The epoxy is then heated prior to spraying onto road surface. Retroreflective glass beads are applied using a separate bead gun behind the epoxy spray gun. Typically, epoxy markings last about 4 years.
Epoxy has been in use since the late 1970s and has gained popularity over the 1990s as the technology has become more affordable and reliable. This material competes directly with plastic with respect to usage and cost.

Negative impacts to road surface

Non-mechanical markers are found to contribute to the deterioration of asphalt concrete road surface courses. The paint and tape markers can cause the road surface to crack, and in more severe cases, the markers contribute to road surface raveling or potholes.
This type of surface damage can be found exclusively underneath the pavement markings such as lane markings and turn-lane arrows. There is no definitive explanation of the relationship between pavement markings and surface deterioration, but there are several hypotheses. One is that water vapor may have been trapped underneath the road surface markings, causing the de-bonding of asphalt binder from the aggregate materials. Another hypothesis is that the reflectivity of the markings may create differences in solar heating and thermal expansion strains between the areas with and without markings. Small flaws caused by differential strains may be combined into longitudinal cracks along the markings. There are certain surface treatments that can make the road surface less susceptible to this type of distresses, such as slurry seals and stone mastic asphalt.

Glass beads

Glass beads composed of soda lime glass are essential for providing retroreflectivity in many kinds of road markings. Retroreflectivity occurs when incident light from vehicles is refracted within glass beads that are imbedded in road markings and then reflected back into the driver's field of view. In the United States, the demand for glass beads has led to importing from countries using outdated manufacturing regulations and techniques. These techniques include the use of heavy metals such as arsenic, antimony, and lead during the manufacturing process as decolourizing and fining agents. It has been found that the heavy metals become incorporated into the bead's glass matrix and may leach under environmental conditions that roads experience.
Abrasion may dislodge these beads from the road marking itself, and the reaction of these beads with an aqueous environment vastly accelerates their decomposition and heavy metal release. During both routine road marking removal and harsh environmental conditions, these glass beads can degrade and leach incorporated heavy metals. There are other, non-toxic metals that can achieve the same results. These may include zirconium, tungsten, titanium, and barium.

Road marking technique

Thermoplastic road marking paint is a solid powder at room temperature. The thermoplastic paint is melted in a specialized machine called a thermoplastic heater-mixer, before being transferred into the paint tank of a marker. Larger marking machines may have internal heater-mixers. The molten coating is introduced into an insulated marking bucket. The marking bucket leads to a marking shoe that applies the material. Moving the shoe forward pulls a thin layer of paint onto the road. The thickness of this layer is controlled by the gap between the marking shoe and the road. A specialized attachment can spread an even layer of glass beads onto the paint as it is deposited.

Machine marking types

Air spray is a method of marking that uses compressed air to spray the paint onto the road surface. The finely atomized paint produces a thin and smooth layer, but the rebounding air flow causes significant paint scattering. This produces somewhat sloppy markings.
High-pressure airless spraying uses a high-pressure airless pump to spray the paint. The atomized paint is not so fine and smooth as air spray, but there is no high speed air flow to scatter any rebounding paint. The marked lines are neat. This method can apply paints of high viscosity, and apply relatively thick layers in a single pass.

Auxiliary equipment

Other equipment is often used with road marking machines. The main auxiliary equipment includes thermoplastic paint pre-heaters, hand-push pre-markers and road marking removers. Thermoplastic paint pre-heater is used to melt the solid powder coating into a viscous liquid, providing a steady supply of paint to the marking machine. Pre-markers are used to draw a field sketch in advance to avoid faulty marking. Road marking removers are used to remove old or incorrect markings. Large self-propelled machines usually do not need any support equipment, as equivalent functionality is built in.

Temporary markers

s are sometimes used to separate High-occupancy vehicle lanes from regular traffic lanes. They are also used in areas where lanes are used at different times for travel in both directions. These cones have shafts that drop into holes in the road surface. A good example of this type of use was the Golden Gate Bridge in San Francisco, before they switched to a moveable barrier system.
Removable tapes can also be used in road construction sites as temporary markers. The tapes can be placed to shift the lanes and black tapes can be used to temporarily blackout the existing markings. At the end of the constructions or within 6 months, the tapes can be pulled out off the surface without using heat, solvents, or machines.

Country specific information

The Americas

Almost all countries in North and South America have solid and intermittent yellow lines separating traffic directions. However, Chile and Argentina have intermittent white lines separating traffic when overtaking is permitted from both directions, and solid yellow lines when overtaking is prohibited from both directions; when overtaking is permitted from only one direction, such countries separate traffic with a combination of white and yellow lines.

Canada

Yellow lines are used to separate traffic moving in opposite directions, and white lines are used to separate traffic moving in the same direction, and on the shoulders of paved roads. On one-directional roads, a yellow line appears on the left shoulder, and a white line on the right shoulder. Passing rules are denoted by dashed lines as in the United States. In Ontario, it is legal to cross a single or double solid yellow line along a straight road and the vehicle is not within 30 metres of a bridge or railway crossing.
Orange painted lines are sometimes used when the direction of the road is altered temporarily for construction projects. However, the colour scheme was reversed before 1971, when white was formerly used to denote the separation of opposing traffic, and yellow lines, when used, to denote the separation of the paved road from the right-hand shoulder.
Broken lines that are wider and closer together than regular broken lines are called continuity lines. Continuity lines on the left side of a lane denote that the lane is about to end and that motorists must soon merge left. Continuity lines on the right mean that the lane will continue, but traffic may merge into it ahead.
In some areas, reflective markers recessed into the pavement are used, especially approaching curves in the road.
A number of provinces have pavement marking test areas on major roads, to evaluate new pavement markings in relation to existing markings. In Ontario, a well-known location is the eastbound lanes of Highway 401 near Belleville. Other test sites are located on the westbound lanes on Highway 417, east of Ottawa, Highway 60 West of Renfrew, Highway 28 east of Bancroft, Highway 400 North of Honey Harbour and on Highway 37, South of Tweed. Pavement marking manufacturers from around the world supply a variety of materials for these sites to have their products evaluated and approved for use on provincial highways. Other provinces with road marking test areas include Quebec, New Brunswick, and Nova Scotia. Quebec's is outside of Montreal on Autoroute 40; in New Brunswick, the area is outside of Fredericton on Highway 2; Nova Scotia's test area is north of Halifax on Highway 102.

United States

In the United States, the first documented use of a painted center line was in 1911 along Trenton's River Road in Wayne County, Michigan. According to the state of Michigan, the idea of using a painted center line was conceived in 1911 by Edward N. Hines, the chairman of the Wayne County, Michigan, Board of Roads, after watching a leaky milk wagon leave a white trail along a road. Hines was the fifth recipient of the George S. Bartlett Award for Highway Progress, and was inducted posthumously in 1972 into the Michigan Transportation Hall of Honor for his innovation, and was honored in 2011 with the first Paul Mijksenaar Design for Function Award.
In 1917, the idea of using painted center lines on rural state highways was conceived and/or put into action in at least three states, apparently completely independent of one another. At some point in 1917, a white highway center line was painted along "Dead Man's Curve" on what is now County Road 492 in Marquette County, Michigan, under the direction of Kenneth Ingalls Sawyer, who served as engineer-superintendent of the Marquette County Road Commission. Sawyer was inducted posthumously into the Michigan Transportation Hall of Honor in 1973.
In Oregon in April 1917, a yellow center line was painted down the center of the Columbia River Highway, between Crown Point and Multnomah Falls, at the direction of Multnomah County Sheriff's Deputy Peter Rexford. Later in 1917, the same line was continued west of Crown Point. Rexford first conceived the idea of a yellow center line in early 1917 while riding on a bus from Salem, Oregon on a dark and rainy night, and advocated it as a safety measure on the Columbia River Highway, which Rexford patrolled as a traffic officer. When Multnomah County declined to fund the project, Rexford's boss, Chief Deputy Martin T. Pratt, paid for the paint out of his own pocket so that the center line could be painted. Rexford later described the April 1917 line as the "first yellow center line ever painted on pavement" in the United States. An article published in The Oregonian upon Rexford's retirement claimed that a contest with a $10,000 reward was once held to determine the originator of the highway center line, but the contest was scrapped when information from Europe revealed that ancient civilizations had used white bricks to mark the center lines of their streets.
In the fall of 1917, Dr. June McCarroll of Indio, California developed the idea of white center lines and began advocating for their use, after she was run off the road by a truck while driving along a highway that would later be incorporated into U.S. Route 99. Dr. McCarroll soon communicated her idea to the local chamber of commerce and the Riverside County Board of Supervisors, with no success. She then took it upon herself to hand-paint a white stripe down the middle of the road, thus establishing the actual width of the lane to prevent similar accidents. In 2002, a portion of Interstate 10 was designated and signed as "The Doctor June McCarroll Memorial Freeway" in her honor.
The question of which colour to use for highway center lines in the United States enjoyed considerable debate and changing standards over a period of several decades. By November 1954, 47 of the 48 states had adopted white as their standard colour for highway centerlines, with Oregon being the last holdout to use yellow. In 1958, the U.S. Bureau of Public Roads adopted white as the standard colour for the new interstate highway system. The 1971 edition of the Manual on Uniform Traffic Control Devices, however, mandated yellow as the standard colour of lines separating opposing traffic nationwide. The changeover to the 1971 MUTCD standards took place between 1971 and 1975, with most done by the end of 1973, so for two years drivers still had to use the old and new. Yellow was adopted because it was already the standard colour of warning signs, and because it was easy to teach drivers to associate yellow lines with dividing opposing traffic and white lines with dividing traffic in the same direction. In turn, this simple mnemonic device greatly reduced head-on collisions and improved road traffic safety.
The major downside to the MUTCD white-yellow system is that yellow has slightly less contrast than white, especially at night, so for maximum contrast, bright yellow—and highly toxic—lead chromate was used to paint yellow lines through the end of the 20th century. As a result, U.S. transportation workers must take special precautions when disturbing or removing yellow lane markings.
, where the lanes are marked only by Botts' dots.
In the U.S., the type, placement, and graphic standards of traffic signs, and road surfaces are legally regulated—the Federal Highway Administration's Manual on Uniform Traffic Control Devices is the standard, although each state produces its own manual based upon the Federal manual.
Generally white lane markings indicate a separation between lanes traveling in the same direction while yellow markings indicate opposing traffic on the other side of the line. In some areas, such as Colorado and Florida, black material is applied on the surface before a shorter white line is painted. This improves the contrast of the marking against "white" pavements, such as concrete or faded asphalt.
In California, Botts' dots are commonly used to mark lanes on most freeways. A large number of California cities also use Botts' dots on some major arterial roads. The notable exception is the city of Los Angeles which only uses paint.
In California and Nevada, the reflectors when present are usually the lines, and no paint is used for additional markings. Exceptions include: freeways built from white concrete where painted stripes are added to make the lanes more visible through sun glare, freeways built so wide that the risk of drifting is minimal, and freeways in areas where it snows in the winter.
In general, single broken lines mean passing or lane changing is allowed, single solid white lines mean lane changing is discouraged or prohibited, and double solid white lines mean it is prohibited, as it often is in tunnels. On two-lane roads, a single broken center line means that passing is allowed in either direction, a double solid center line means passing is prohibited in both directions, and the combination of a solid line with a broken line means that passing is allowed only from the side with the broken line and prohibited from the side with the solid line. The solid white line on the right side is called the 'fog line' used to help cars stay in their lane during foggy conditions and help pedestrians stay off the road.
Marked crosswalks are indicated at a minimum by a pair of white lines. On major boulevards, crosswalks are further highlighted by zebra stripes, which are large white rectangles in the crosswalk perpendicular to traffic. In order to maximize the longevity of zebra crossing stripes, they are usually applied to correspond with the portions of the lane on which the wheels of a car are not usually traveling, thereby reducing wear on the markings themselves.
Pavement markings are used in addition to signs in the United States to designate regular and handicap parking spaces. Regular parking spaces are normally marked with white, although other colours are used. Handicap parking spaces are required to be located within a specified distance of an entrance. Blue markings are used to indicate the parking space is reserved for persons with a disabled parking permit.

Asia

Hong Kong

Road markings in Hong Kong are basically identical with the United Kingdom, with longer dashed white lines to indicate lanes of opposing traffic, and shorter dashed white lines for lanes in the same direction. Solid double white lines are used to indicate that drivers are not permitted to change lanes. A solid white line with a broken white line indicates that crossing the line is allowed from the lane closer to the broken line. Double solid white lines are in place in all tunnels and underpasses.
As in the UK, solid yellow lines are painted along the kerbside to indicate that no parking is allowed, with double solid yellow lines meaning no parking is allowed at any time. But unlike the UK loading and unloading are also prohibited in addition to parking. Zig-zag lines are used on both ends of zebra crossings. Road studs are also used as in the UK.

Japan

In Japan, white always separates traffic in the same direction or indicates traffic in the same direction can use a buffered area that is striped in crosshatch patterns such as at right turns on two-way roads since Japan is a country that has left-side driving.
White is also used on divided expressways with a solid raised center divider. Two-lane expressways where poles are the only physical barrier between opposing directions of travel always have yellow either side of the row of poles, and white is between the yellow striping and the poles.
White is also used to denote passing allowed on other two-lane roads. Yellow indicates no passing is allowed. On all roads, yellow stripes are always solid.
On expressways where there are many sharp turns and curves, seen especially in the largest cities, a yellow line indicates no passing between lanes, as follows:
Other markings include in the cities, destination and exit names painted in the lanes, which is done due to the very close proximity of exits, where in many cases it would be impractical to put up many overhead signs, although these are often seen approaching exits, a curved or slanted arrow points to the side of the expressway the exit will be on. A straight arrow following characters indicates the destination of the expressway.
Where a solid white line appears between lanes, passing is generally allowed but with caution.

Europe

In general European countries follow the Vienna Convention on Road Signs and Signals, which describes what road signs and road markings shall look like. The convention has some flexibility so road markings vary somewhat between the countries.
Most European countries reserve white for routine lane markings of any kind. Yellow is used to mark forbidden parking, such as on bus stops. However, for example Norway has yellow markings separating traffic directions. Many countries use yellow, orange, or red to indicate when lanes are being shifted temporarily to make room for construction projects.
In France on highways the outside lines are interrupted at a regular distance which allows drivers and police to check distance between moving vehicles.
In the Netherlands, Germany, Sweden, and the UK, so-called "naked roads" have been trialed, whereby all visible road markings, kerbs, traffic lights, and signs are removed, on urban roads. When this was tested in Seend, a village in the UK county of Wiltshire in 2005, the county council reported that accidents fell by a third, with motorists' speed falling by an average of 5%. It has been suggested that naked roads force drivers to make eye contact with other road users, and that it is this nonverbal communication that is responsible for the reduction of accidents. Other have suggested that road markings, especially with middle marker, make the road look like a main road, triggering faster and more relaxed driving, while no marking makes the road look like a lower quality road.
It is an experience from the introduction of marking, that at least on narrow roads and in curves, middle lines help make drivers stay on their side when meeting, and therefore reducing meeting accidents. Note that the 2005 experiment was on urban roads. In Sweden, local streets generally have no marking.
In Israel, white lines are used to separate both traffic driving in the same direction and in opposite directions, while yellow lines are used to mark the shoulder of the road.

Netherlands

In the Netherlands all general lines are white, while yellow lines are used to mark forbidden stopping, forbidden parking and for temporarily lining at construction projects.
Shoulder lines are generally interrupted outside built-up area to make the driver be aware the presence of crossing bicycles and pedestrians, driveways and stopping cars. Wider roads sometimes have a single, but in most cases have a double centre line. Interrupted center lines mean overtaking is allowed, a solid line means overtaking is not allowed, depending on which side of a double line is solid. Smaller roads and roads where bicycles are allowed generally do not have center lines, and many country roads have no lines at all. Sometimes there is a center line only in sharp curves.
Shoulder lines on expressways and motorways are solid to imply the general absence of crossing traffic and residential driveways, as well as the disallowance of leaving the road on places other than specified exits. Expressways always have double centre lines. Exit and acceleration lanes are separated by 'block marking'.
Furthermore, several traffic signs are painted on the road, such as speed limits and warning sings.

Norway

In Norway, yellow lines are used to separate traffic moving in opposite directions and on the left shoulders of paved roads, and white lines are used to separate traffic moving in the same direction, and on the right shoulders of paved roads. On roads narrower than, the centerline is removed, and the shoulder lines are broken. Short, broken lines means passing is allowed, long, broken lines means passing is allowed but dangerous, and a double yellow line means passing is forbidden. Roads with speed limits below that indicate that passing is allowed but dangerous have a very short yellow line instead of a long one. On motorways, the left shoulder is a yellow line, like in the US. Most other European countries use white lines for all these types of lines.

United Kingdom

In the UK, the first "white line" road markings appeared on a number of dangerous bends on the London-Folkestone road at Ashford, Kent, in 1914.
In England, the idea of painting a centre white line was first experimented with in 1921 in Sutton Coldfield, Birmingham. Following complaints by residents over reckless driving and several collisions, the Sutton Coldfield Corporation decided to paint the line on Maney Corner in the area of Maney.
In 1971, a correspondent for the Sutton Coldfield News wrote an article in the newspaper recalling the event.
During the World War II the Pedestrians Association lobbied for the government to make it safer for pedestrians to walk during the black out. As a result, white lines were painted on the sides of the road and pedestrians were allowed to use a small torch.
In the UK, the first "white line" road markings appeared on a number of dangerous bends on the London-Folkestone road at Ashford, Kent, in 1914, and during the 1920s the rise of painted lines on UK roads grew dramatically. In 1926 official guidelines were issued by the Ministry of Transport that defined where and how white lines on roads should be used. A broken white line in the direction of travel, where the gaps are longer than the painted lines, indicates the centre of the road and that there are no hazards specific to the design and layout of the road, i.e. no turnings, sharp bends ahead etc. A broken white line in which the gaps are shorter than the painted lines indicates an upcoming hazard.
The Ministry of Transport experimented with double-line road markings for the first time on sections of the A20 and A3 during Easter in 1957. The markings were cautionary, and had no legal status at that time, but motorists were advised that ignoring them could weigh heavily against someone involved in an accident in their vicinity. Further, "it is in order, if safe to do so, to cross the lines only when the broken one is on your side. It is not in order to cross when the solid line is on your side or to park there." Despite the instruction about parking, it was observed that nine bus stops were located inside prohibited parking areas.
A double solid white line indicates that the line may not be crossed, overtaking is permitted if it can be performed safely without crossing the line. Solid lines can be crossed in certain specific conditions. A solid white line with a broken white line parallel to it indicates that crossing the line is allowed for traffic in one direction and not the other.
Solid white lines are also used to mark the outer edges of a road.
A double yellow line next to the kerb means that no parking is allowed at any time, whilst a single yellow line is used in conjunction with signs to denote that parking is restricted at certain times. Double and single red lines mean that stopping is not allowed at any time or between certain times respectively.
On many roads in the UK, retro-reflective road studs, including those known as "cat's eyes" when referring to the Halifax type road stud, are placed in the road. These devices reflect the light from a car's headlights back towards the driver in order to highlight features of the road in poor visibility or at night. The colour of road studs differs according to their location. Those defining the division between lanes are white, red road studs are placed along the hard shoulder of motorways, dual carriageways and other roads to mark the left-hand edge of a running lane; and orange road studs are placed along the edge of the central reservation. Green road studs denote slip roads at grade-separated junctions and also road-side lay-bys.
Comprehensive information about highway markings in the UK can be found in the Highway Code and on the .

Russia

In Russia, yellow lines may be used instead of white lines to separate oncoming traffic flows. They were authorized only recently, in 2018, and were first painted on a short stretch of federal highway A138 in Murmansk Oblast. Broken yellow lines at the edge of the road mean that you cannot park, but can stop for up to 5 minutes, or more if that is needed to load and unload people or cargo. A solid yellow line on the edge of the road denotes that stopping is prohibited.

Oceania

Australia

In Australia, white lines are generally used both to separate traffic flowing in the same direction and traffic flowing in opposite directions. Double solid white center-lines may not be crossed under any circumstances, unless avoiding an obstruction. Dashed lines may be crossed for overtaking, changing lanes or turning, and also in the case of double-line markings provided the dashed line is on your side of the markings. For this reason, dashed lines are usually used to mark multiple lanes traveling in the one direction. Yellow lines along road edges are used nationally to indicate "No Standing" areas not otherwise marked by signs. Solid white lines are also used to indicate kerbside parking, pedestrian and bicycle lanes, and other kerbside features. Yellow line markings are also used in areas that receive regular annual snowfall to provide contrast. Double-line markings are used to separate traffic flowing in opposite directions on busy roads.
Solid white lines are used to mark an intersection that a driver must stop at before entering whilst obeying all right-of-way laws. Dashed white lines are used to mark an intersection at which a driver must give way. Dashed white lines are also commonly used to indicate turns in intersections and to indicate intersections where a diamond turn is possible.
Materials used are waterborne paint, thermoplastics, and cold applied plastic, all with glass bead. Bead is generally 1mm for longitudinal marking. Currently moving to performance specified contracts with the primary performance indicator being retro-reflectivity measured with geometry instruments. Intervention levels vary generally from 100 to 150 mcd/lux/m2.

New Zealand

Although New Zealand follows the convention of a solid yellow line to indicate no passing on roads with two-way traffic, it uses dashed white lines with a gap to indicate when passing against opposing traffic is allowed on two-lane roads and shorter ones to separate lanes going in the same direction. The New Zealand convention followed the USA MUTCD convention common between 1961 and the early 1970s.