Rotodynamic pump


A rotodynamic pump is a kinetic machine in which energy is continuously imparted to the pumped fluid by means of a rotating impeller, propeller, or rotor, in contrast to a positive displacement pump in which a fluid is moved by trapping a fixed amount of fluid and forcing the trapped volume into the pump's discharge. Examples of rotodynamic pumps include adding kinetic energy to a fluid such as by using a centrifugal pump to increase fluid velocity or pressure.

Introduction

A pump is a mechanical device generally used for raising liquid from a lower level to higher one. This is achieved by creating a low pressure at the inlet and high pressure at the outlet of the pump. Due to low inlet pressure, the liquid rises from where it is to be stored or supplied. However, work has to be done by a prime mover to enable it to impart mechanical energy to the liquid which ultimately converts into pressure energy.
Considering the basic principle of operation, pump can be classified into two categories:
  1. Positive displacement pumps.
  2. Non-positive displacement pumps.

    Classification of pumps

Pumps are classified as follows:

Positive displacement pump

A positive displacement pump can operate by forcing a fixed volume of fluid from inlet pressure section of the pump into the discharge zone of the pump. It can be classified into two types:
  1. Rotary-type positive displacement pump:
  2. * Internal gear pump
  3. * Screw pump
  4. Reciprocating-type positive displacement pump:
  5. * Piston pump
  6. * Diaphragm Pump

    Rotary-type positive displacement pump

Positive displacement rotary pump can move the fluid by using a rotating mechanism that creates a vacuum that captures and draws in the liquid. Rotary positive displacement pump can be classified into two main types:
  1. Gear pumps
  2. Rotary vane pumps

    Reciprocating-type positive displacement pump

Reciprocating pumps move the fluid using one or more oscillating pistons, plungers or membranes, while valves restrict fluid motion to the desired direction.
Pump in this category are simple with one cylinder or more. They can be either single-acting with suction during one direction of the piston motion and discharge on the other or double-acting with suction and discharge in both directions.

Non- positive displacement pump

With this pump, the volume of the liquid delivered for each cycle depends on the resistance offered to flow. A pump produces a force on the liquid that is constant for each particular speed of the pump. Resistance in a discharge line produces a force in the opposite direction. When these forces are equal, a liquid is in a state of equilibrium and does not flow. If the outlet of a non positive-displacement pump is completely closed, the discharge pressure will rise to maximum for a pump operating at a maximum speed.

Centrifugal pumps

Centrifugal pumps are the machines, which employ centrifugal force to lift liquids from a lower level to a higher level by developing pressure. A simplest type of pump comprises an impeller fitted onto a shaft, rotating in a volute casing. Liquid is led into the centre of the impeller, and is picked up by the vanes of the impeller and accelerated to a high velocity by the vanes of the impeller, and discharged by the centrifugal force into the casing and then out the discharge pipe. When liquid is forced away from the centre, a vacuum is created and more liquid receives energy from the vanes and gains in pressure energy and kinetic energy. Since a large amount of kinetic energy is not desirable at the impeller outlet, an arrangement is made in the design to convert the kinetic energy of the liquid to pressure energy before the liquid enters the discharge pipe.

Types of rotodynamic pumps

Rotodynamic pumps can be classified on various factors such as design, construction, applications, service etc.
is the most common used pumping device in the hydraulic world. In which the water comes from the tank at the center of the impeller and exits at the top of the pump. The impeller is called the heart of the system. Which have three types 1. Open impeller, 2. Semi-open impeller, 3. Enclosed impeller, in which the enclosed impeller gives the best efficiency. Enclosed impellers have a series of backward-curved vanes fitted between the two plates. It will always stay in the water. When impeller starts to rotate, the fluid in which the impeller lies will also rotate. When fluid starts to rotate, the centrifugal force will induced in the fluid particles. Due to centrifugal force, both pressure and kinetic energy of fluid will increases. As the centrifugal force occurs in the fluid particles, at the inlet nozzle side the pressure will decreases. The pressure will comparatively less than the atmospheric pressure. Such low pressure will help to suck the fluid from the storage. But if the inlet nozzle is empty or filled with the air it will damage the impeller. The difference between pressure created at the inlet nozzle and the atmospheric pressure will be very less to suck the fluid from the tank. The impeller if fitted inside the casing. So the fluid has to be inside the casing. Casing will be designed such that it will give maximum pressure at the exit. In casing, the maximum diameter or space is at exit and as we move inside the diameter will gradually decrease. Due to this, the volume of the fluid is more at the discharge nozzle, so the velocity will decrease, and as velocity and pressure both are inversely proportional the pressure will increase. And the increase in pressure is required because to overcome the resistance of the pumping system.
If the pressure at the inlet nozzle goes below the pressure of vapor of the fluid, air bubbles created inside the casing. This situation is very dangerous for the pump because the fluid starts to boil and form the bubbles. Those bubbles will hit the impeller and it will spoil its material. This situation is known as the cavitation. To increase the pressure at the inlet nozzle we have to decrease the section head.
Those three types of impellers have its different usages. If the fluid is more cloggy then the semi open or the open type of impeller is used. But the efficiency will decreases respectively. And also the Mechanical design of the pump is difficult. The shaft is used to connect the impeller and the motor which will transfer the rotary motion to the impeller. The fluid pressure inside the casing is very high, a proper sealing arrangement is required.

Applications

Main industries where rotodynamic pumps are used include: