Shore durometer


The Shore durometer is a device for measuring the hardness of a material, typically of polymers, elastomers, and rubbers.
Higher numbers on the scale indicate a greater resistance to indentation and thus harder materials. Lower numbers indicate less resistance and softer materials.
The term is also used to describe a material's rating on the scale, as in an object having a “‘Shore durometer’ of 90.”
The scale was defined by Albert Ferdinand Shore, who developed a suitable device to measure hardness in the 1920s. It was neither the first hardness tester nor the first to be called a durometer, but today that name usually refers to Shore hardness; other devices use other measures, which return corresponding results, such as for Rockwell hardness.

Durometer scales

There are several scales of durometer, used for materials with different properties. The two most common scales, using slightly different measurement systems, are the ASTM D2240 type A and type D scales.
The A scale is for softer ones, while the D scale is for harder ones.
However, the ASTM D2240-00 testing standard calls for a total of 12 scales, depending on the intended use: types A, B, C, D, DO, E, M, O, OO, OOO, OOO-S, and R. Each scale results in a value between 0 and 100, with higher values indicating a harder material.

Method of measurement

Durometer, like many other hardness tests, measures the depth of an indentation in the material created by a given force on a standardized presser foot. This depth is dependent on the hardness of the material, its viscoelastic properties, the shape of the presser foot, and the duration of the test. ASTM D2240 durometers allows for a measurement of the initial hardness, or the indentation hardness after a given period of time. The basic test requires applying the force in a consistent manner, without shock, and measuring the hardness. If a timed hardness is desired, force is applied for the required time and then read. The material under test should be a minimum of 6 mm thick. Theoretical background of the test is considered e.g. in
DurometerIndenting footApplied mass Resulting force
Type AHardened steel rod 1.1 mm – 1.4 mm diameter, with a truncated 35° cone, 0.79 mm diameter0.8228.064
Type DHardened steel rod 1.1 mm – 1.4 mm diameter, with a 30° conical point, 0.1 mm radius tip4.55044.64

The ASTM D2240 standard recognizes twelve different durometer scales using combinations of specific spring forces and indentor configurations. These scales are properly referred to as durometer types; i.e., a durometer type is specifically designed to determine a specific scale, and the scale does not exist separately from the durometer. The table below provides details for each of these types, with the exception of Type R.
Durometer typeConfigurationDiameterExtensionSpring force
A35° truncated cone
B30° cone
C35° truncated cone
D30° cone
E spherical radius
M30° cone
O spherical radius
OO spherical radius
DO spherical radius
OOO spherical radius
OOO-S radius disk

Note: Type R is a designation, rather than a true "type". The R designation specifies a presser foot diameter of 18 ± 0.5 mm in diameter, while the spring forces and indenter configurations remain unchanged. The R designation is applicable to any D2240 Type, with the exception of Type M; the R designation is expressed as Type xR, where x is the D2240 type, e.g., aR, dR, etc.; the R designation also mandates the employment of an operating stand.
Some conditions and procedures that have to be met, according to DIN ISO 7619-1 standard are:
The final value of the hardness depends on the depth of the indenter after it has been applied for 15 seconds on the material. If the indenter penetrates 2.54 mm or more into the material, the durometer is 0 for that scale. If it does not penetrate at all, then the durometer is 100 for that scale. It is for this reason that multiple scales exist. But if the hardness is <10 °Sh or >90 °Sh the results are not to be trusted. The measurement must be redone with adjacent scale type.
Durometer is a dimensionless quantity, and there is no simple relationship between a material's durometer in one scale, and its durometer in any other scale, or by any other hardness test.
MaterialDurometerScale
Bicycle gel seat15–30OO
Chewing gum20OO
Sorbothane30–70OO
Rubber band25A
Door seal55A
Automotive tire tread70A
Soft wheels of roller skates and skateboard78A
Hydraulic O-ring70–90A
Pneumatic O-ring65-75A
Hard wheels of roller skates and skateboard98A
Ebonite rubber100A
Solid truck tires50D
Hard hat 75D
Cast urethane plastic80D

ASTM D2240 hardness and elastic modulus

Using linear elastic indentation hardness, a relation between the ASTM D2240 hardness and the Young's modulus for elastomers has been derived by Gent and by Mix and Alan Jeffrey Giacomin. Gent's relation has the form
where is the Young's modulus in MPa and is the ASTM D2240 type A hardness.
This relation gives a value of at but departs from experimental data for. Mix and Giacomin derive comparable equations for all 12 scales that are standardized by ASTM D2240.
Another relation that fits the experimental data slightly better is
where is the error function, and is in units of Pa.
A first-order estimate of the relation between ASTM D2240 type D hardness and the elastic modulus of the material being tested is
where is the ASTM D2240 type D hardness, and is in MPa.
Another Neo-Hookean linear relation between the ASTM D2240 hardness value and material elastic modulus has the form
where is the ASTM D2240 type A hardness, is the ASTM D2240 type D hardness, and is the Young's modulus in MPa.

Patents

*