Ski binding

Alpine

Alpine touring

• , for traditional alpine boots. In this variation the pivot is located in the front of the binding.
• , for boots in which the pivot is formed at the boot / binding interface.

Nordic

Cable binding

Rottefella (NN, Nordic Norm)

NNN (New Nordic Norm)

NIS (Nordic Integrated System)

SNS (Salomon Nordic System)

• SNS Profil: One metal bar in the toe of the boot.
• SNS Pilot: Two metal bars on the boot.
• SNS X-Adventure: Stronger design used for back-country skiing.

• SNS: "U-shaped" metal bar protruding from the front of the boot

  Prolink (Salomon NNN-compatible system)

NTN (New Telemark Norm)

IFP (Turnamic)

NIS 2.0 (MOVE)

History

• 1840s: Sondre Norheim demonstrated Telemark skiing before 1866, and the Open Christiania in 1868, both made possible with a binding design. This added a loop of twisted birch roots that ran from the existing birch root toe loops around the boot heels and back. This allowed the heel to lift as before, for walking and gliding, but better held the boots to the skis allowing greater control. This enabled Norheim to control the skis with his feet and legs, replacing the former technique of dragging a large pole in the snow on one side or the other to drag the skier in that direction. These new techniques spread throughout Telemark and would later be named for the region.
• 1894: Fritz R. Huitfeldt invented a binding with a secure toe iron which allowed the heel to move freely. This became the standard industry binding through the 1930s. Huitfeldt drove the evolution of the ski binding over the next 20 years. In 1894, he introduced the use of semi-circular metal hooks at the toe to attach the straps. The hooks were positioned to tightly fit to the sides of the boot, keeping the ski centred and eliminating any "flop" that the formerly loose straps allowed. The heel strap was also attached to the same hooks, but because of their rounded shape, the required range of motion was provided by the straps sliding up and down on the hooks. This allowed the heel strap to be replaced by a less flexible leather strap. Together, these changes dramatically tightened the binding, greatly increasing control.
• 1897: Huitfeldt further improved the design by changing the toe piece. Instead of hooks, he drilled a rectangular hole through the ski from side to side, and passed an iron bar through it. The bar was then bent up on either side, locking it in place, and then formed to fit the toe of the boot. This improvement once again dramatically improved the firmness of the fit. Finally, in 1904 he adopted the Hoyer-Ellefsen toggle, a lever that replaced the buckles. This not only greatly improved mechanical advantage, further improving the strength of the binding, but also made the system much easier to put on and remove. Better yet, the geometry of the attachment points meant the heel strap was mechanically attached below that of the toe strap, which provided a constant "diagonal downpull" that naturally returned the heel to the ski.
• 1920: Huitfeldt style bindings were by far the most popular system for decades, with the only major change being Marius Eriksen's 1920 introduction of pre-formed plates that were screwed on top of the ski. Other binding systems did exist, in particular a class of bindings originally introduced by Mathias Zdarsky that replaced the heel strap with a long metal plate under the sole of the boot, hinged at the front to allow the heel to rise. The heel was held to the plate by a short strap attaching at the back. These gave even better control than the Huitfeldt design, but so firmly attached the leg that injury was a real problem.
• 1927: Change eventually came through the evolution of the Rottefella binding, first introduced in 1927. The original Rottefella eliminated the heel strap, which held the boot forward in the binding, by drilling small holes in the sole of the boot which fit into pins in the toe piece. This would only work if the sole was held very firmly down on the pins, so the binding also introduced a metal clip that was forced down onto the top of the sole of the boot, forcing it onto the pins. When the inventor, Bror With, won a race on the new design, Norwegian Crown Prince Olav asked him what they were, and he responded "Oh, they're just a couple of rat traps I picked up at the hardware store". "Rottefella" is Norwegian for "rat trap".
• 1929: The introduction of the cable binding allowed the Christie turn to become a standard on downhill runs, and to further support this style of skiing the Swiss racer Guido Reuge in 1929 invented a cable binding with steel clips below the boot heel to enable clamping the heel down for downhill portions. He named the product "Kandahar" for the international Kandahar Cup ski races. In use in alpine races, the Kandahar binding led to serious leg injuries, and by 1939 experimentation began in earnest on bindings that would release the boot in a fall.
• 1932: a major advance on the Huitfeldt concept was introduced to the market by Guido Reuge in 1932. Reuge replaced the heel strap with a metal cable connected to a spring at the front of the toe. The spring provided even tension as the boot moved. Previously, the strap was adjusted so it had enough slack to allow the boot to rotate as high as the skier wished, but as the boot rotated back down to the ski it became increasingly slack again. The cable removed this limitation, and held the boot firmly through its entire motion, greatly increasing the solidity of the fit. A later advance added two small metal clips near the rear of the foot that the cable could be clipped under. These held the boot firmly to the ski during downhill portions of the runs. Cable bindings remained in use for some time for cross-country, and are today popular for telemark skiing. However, the Rottefella design from the 1930s became more popular for Nordic skiing through the 1950s and into the 1970s until the Salomon Nordic System binding entirely re-invented bindings used for Nordic skiing.
• 1937: Hjalmar Hvam broke his leg skiing, and while recuperating from surgery, invented the Saf-Ski toe binding. This was a metal clip with a pyramidal top that fit into a slot cut into the sole of the ski boot. When the boot was rotated forward, the slot on the toe eventually rose above the metal pyramid, allowing the toe to release from the ski. The system was considered with suspicion by professional skiers, especially when Olaf Rodegaard released during a race. However, Rodegaard credits the release with saving him from a broken leg. In the post-war era, Hvam sold several thousand pairs of Saf-Ski's, in an era when alpine skiing was in its infancy. Hvam continued to sell the Saf-Ski into the 1960s, but in 1966 his insurance rates increased so dramatically that he was forced from the market.
• 1950: A dramatic advance in alpine ski bindings was introduced as the Look Nevada in 1950. The Nevada held the toe centred over the ski using two metal fingers shaped into an upside-down V. The fingers were pivoted to allow motion to the sides, and centred with a spring. During a fall, sideways torsion could overcome the force of the spring and allow the boot to release directly to the side. This design was quickly copied by other vendors, notably Marker, and had the first real impact on the dominance of the fixed-toe bindings. By the late 1950s, there were about 35 different release toe bindings on the US market, most of which used a normal Kandahar-style heel cable.
• 1960: The first modern heel-and-toe binding for alpine skiing was the Cubco binding, first introduced in 1950 but not popular until about 1960. A heel-release binding faced the problem that there was no obvious place to attach to on the heel, so the Cubco solved this by screwing small metal clips into the sole of the boot. This also eliminated the changes in performance as the sole of the boot wore down, or the geometry of the sole changed as the boot wore into the skier's foot. Marker introduced the Rotomat, which gripped onto the sole where it extended past the heel, and Look quickly followed suit with their Grand Prix design. By the mid-1960s, release bindings that worked on both the heel and the toe were common, and by the late 1960s, the cable binding had disappeared from alpine skiing.
• 1966: The introduction of plastic ski boots permitted the development of industrial standards for the function of alpine skiing bindings.
• 1972: Injury rates from alpine skiing began to fall with the gradual introduction of the Teflon anti-friction pad around 1972.
• 1970s:
• *Alpine: One problem with 1960s release bindings was that the boots were not standardized, and a binding that worked well on one boot might be dangerous on another, or might become dangerous over time as the boot shifted about. This led to the introduction of plate bindings, which used a metal plate firmly clipped to the sole of the boot, and bindings that clamped onto the plate. The plate could be easily removed for walking about. Plate bindings were popular in the US in the 1970s, notably the BURT Retractable Bindings and Spademan binding, but never caught on in any major way in Europe. As more and more of the alpine skiing market came under control of European companies, the plate bindings disappeared, in spite of their excellent safety records. The disappearance of the plate and alternate systems was due to a combination of factors, notably the introduction of standardized hard plastic boots. Plastic was first introduced by Lange as a way of improving existing leather designs. As the new material spread through the industry, the sole piece was standardized to allow toe-and-heel bindings to clip on. Plastic had the advantages of being much firmer than leather, not changing shape over time, and having predictable friction characteristics wet or dry. Although plate bindings of the era had much better safety records, notably the Spademan design, the new boots and bindings could be easily adapted to any ski for any skier.
• * Nordic: Problems with the geometry of the boot sole, which meant only certain boots would work, meant the Rottafella was not widely used. This problem was eventually solved through the same evolution of plastic components that changed the alpine skiing market. The use of highly flexible plastics allowed for a sole that was very strong torsionally and side-to-side, but still had excellent flexibility lengthwise, allowing the heel to rise as with a cable binding. This was standardized as the 3-pin system, which was widespread by the 1970s. A similar system with a 50 mm "duckbill" once existed for lighter setups, but is obsolete and no longer available. Unlike the 75 mm it was symmetric. It was the binding of choice for racing, before the adoption of skate ski racing, in the early 1970s. The 50 mm was also designated according to the thickness of the "duckbill" having either 7 mm or 11–13 mm thick soles hence these bindings often had two notches in the bail to clamp boots with different sole thicknesses.
• 1980s: