South African Class 16E


The Spoornet Class 16E of 1990 was a South African electric locomotive.
During 1990 and 1991, Spoornet semi-permanently coupled several pairs of otherwise unmodified Series 2 to Series 9 Class 6E1 electric locomotives, reclassified them to Class 16E and allocated a single shared unit number to each pair, with the individual locomotives in the pairs inscribed "A" or "B".

Manufacturer

The 3 kV DC Class 6E1 electric locomotive was built for the South African Railways by Union Carriage & Wagon in Nigel, Transvaal. The electrical equipment was supplied by the General Electric Company. UCW did not allocate builder's numbers to the locomotives which it built for the SAR, but used the SAR unit numbers for their record keeping.

Characteristics

Bogies

The Class 6E1 was built with sophisticated traction linkages on their bogies. Together with the locomotive's electronic wheel-slip detection system, these traction struts, mounted between the linkages on the bogies and the locomotive body and colloquially referred to as grasshopper legs, ensured the maximum transfer of power to the rails without causing wheel-slip by reducing the adhesion of the leading bogie and increasing that of the trailing bogie by as much as 15% upon starting. This feature was controlled by electronic wheel-slip detection devices and an electric weight transfer relay which reduced the anchor current to the leading bogie by as much as 50A in notches 2 to 16.

Brakes

The locomotive itself used air brakes, but it was equipped to operate trains with air or vacuum brakes. While hauling a vacuum braked train, the locomotive's air brake system would be disabled and the train would be controlled by using the train brakes alone to slow down and stop. While hauling an air braked train, on the other hand, the locomotive brakes would engage along with the train brakes. While working either type of train downgrade, the locomotive's regenerative braking system would also work in conjunction with the train brakes.
When the locomotive was stopped, the air brakes on both bogies were applied together. The handbrake or parking brake, located in cab no. 2, only operated on the unit's last axle, or no. 7 and 8 wheels.

Orientation

These dual-cab locomotives had a roof access ladder on one side only, just to the right of the cab access door. The roof access ladder end was marked as the no. 2 end. A corridor along the centre of the locomotive connected the cabs, which were identical apart from the fact that the handbrake was located in cab 2. A pantograph hook stick was stowed in a tube mounted below the lower edge of the locomotive body on the roof access ladder side.

Class 16E pairing

Class 16E electric locomotives were two-unit semi-permanently coupled Class 6E1 pairs coupled at their no. 1 ends. The aim was to accomplish savings on cab maintenance by abandoning the no. 1 end cabs in terms of maintenance and using only the no. 2 end cabs. During 1990 and 1991 Spoornet made up several such semi-permanently coupled pairs of otherwise unmodified Series 3 to Series 9 Class 6E1 locomotives, each pair getting reclassified to Class 16E, renumbered to a shared new unit number and with each unit inscribed as either the A or B unit.
This was unlike the procedure which was followed later with Class 17E locomotives which were internally modified and reclassified Class 6E1 Series 7, 8 and 9 locomotives, but which remained in service as individual locomotives and retained their original unit numbers after reclassification.
The original intent was to convert all the serving Class 6E and all eleven series of Class 6E1 to Class 16E locomotive pairs, with the following planned Class 16E number allocation:
The idea was not well thought through, however, and the law of unintended consequences soon manifested itself. In practice it was found that some locomotive pairs worked together better than others so that some pairings were successful while others gave problems. Maintenance issues presented further drawbacks since when only one unit in a Class 16E pair needed repairs, it meant that the partner was out of commission as well because their no. 1 end cabs were not kept serviceable. All these and other complications led to the programme being abandoned very quickly, long before all the Class 6E and 6E1 could be paired off.
A few of the successful and problem-free Class 16E pairings did continue to run that way for more than fifteen years with numbers and B and 16-411A and B being the last to be separated. The rest were either separated during rebuilding to Class 18E or gradually converted back to dual cab Class 6E1s as soon as one or both in the pair required major maintenance, all of the latter reverting to their original Class 6E1 unit numbers. Their former Class 16E numbers were still visible on many of these locomotives years later.
None of the Class 6E or the Class 6E1, Series 1, 10 or 11 locomotives were ever paired into Class 16Es. Those which are known to have received this treatment are shown in Table 1.

16E no.		A
Unit		B
Unit		6E1
Series		A Unit
to 18E no.		B Unit
to 18E no.
16-100E1272E12732
16-227E1418E14193
16-305E14574
16-319E15495
16-335E16075
16-404E1846E1847718-35918-360
16-405E1848E1849718-26418-265
16-406E18707
16-407E1790718-184
16-409E1840E1841718-33818-339
16-410E1850E1851718-39218-393
16-411E1858E18597
16-420E16536
16-422E1669E1709618-10018-503
16-425E1699E1700618-16718-169
16-427E1684E1701618-34518-346
16-428E1718E1720618-34718-348
16-429E1679E1714618-34918-350
16-500E2001E2002918-02918-030
16-501E1916E1917818-03518-036
16-503E1914E1915818-07718-078
16-504E1925E1926818-03318-034
16-505E1918E1919818-06318-067
16-506E1928E1929818-05518-049

Rebuilding to Class 18E

Beginning in 2000, Spoornet embarked on a project to rebuild Series 2 to 11 Class 6E1 locomotives as well as Class 16E pairs which were originally from those series to Class 18E, Series 1 and Series 2 at the Transnet Rail Engineering workshops at Koedoespoort. In the process, the cab at the no. 1 end was stripped of all controls and the driver's front and side windows were blanked off to have a toilet installed, thereby forfeiting the locomotive's bi-directional ability.
Since the driving cab's noise level had to be below 85 decibels, cab 2 was selected as the Class 18E driving cab primarily based on its lower noise level compared to cab 1 which was closer and more exposed to the compressor's noise and vibration. Another factor was the closer proximity of cab 2 to the low voltage switch panel. The fact that the handbrake was located in cab 2 was not a deciding factor, but was considered an additional benefit.
While the older Class 6E1, Series 2 to 7 locomotives had been built with a brake system consisting of various valves connected to each other with pipes and commonly referred to as a "bicycle frame" brake system, the Class 6E1, Series 8 to 11 locomotives were built with a compressed air equipment frame brake system, commonly referred to as a brake rack. Since the design of the rebuilt Class 18E locomotives included the same brake rack, the rebuilding project was begun with the newer series 8 to 11 locomotives to reduce the overall cost of rebuilding.
The known Class 16E locomotives which were used in this project were all rebuilt to Class 18E, Series 1 locomotives. Their numbers and renumbering details are shown in Table 2.

Count		6E1
no.		6E1
series		Year
built		18E
no.		Year
rebuilt		Notes
1E16696197618-1002003ex 16-422A
2E16796197618-3492007ex 16-429A
3E16846197618-3452007ex 16-427A
4E169961976-7718-1672004ex 16-425A
5E170061976-7718-1692004ex 16-425B
6E170161976-7718-3462007ex 16-427B
7E170961976-7718-5032009ex 16-422B
8E171461976-7718-3502007ex 16-429B
9E17186197718-3472007ex 16-428A
10E17206197718-3482007ex 16-428B
11E179071977-7818-1842005ex 16-407B
12E18407197818-3382007ex 16-409A
13E18417197818-3392007ex 16-409B
14E18467197818-3592007ex 16-404A
15E18477197818-3602007ex 16-404B
16E18487197818-2642006ex 16-405A
17E18497197818-2652006ex 16-405B
18E18507197818-3922008ex 16-410A
19E18517197818-3932008ex 16-410B
20E19148197918-0772003ex 16-503A
21E19158197918-0782003ex 16-503B
22E191681979-8018-0352002ex 16-501A
23E191781979-8018-0362002ex 16-501B
24E191881979-8018-0632002ex 16-505A
25E191981979-8018-0672003ex 16-505B
26E192581979-8018-0332002ex 16-504A
27E192681979-8018-0342002ex 16-504B
28E192881979-8018-0552002ex 16-506A
29E192981979-8018-0492002ex 16-506B
30E20019198118-0292002ex 16-500A
31E20029198118-0302002ex 16-500B

Illustration