Crank (mechanism)
A crank is an arm attached at a right angle to a rotating shaft by which circular motion is imparted to or received from the shaft. When combined with a connecting rod, it can be used to convert circular motion into reciprocating motion, or vice versa. The arm may be a bent portion of the shaft, or a separate arm or disk attached to it. Attached to the end of the crank by a pivot is a rod, usually called a connecting rod.
The term often refers to a human-powered crank which is used to manually turn an axle, as in a bicycle crankset or a brace and bit drill. In this case a person's arm or leg serves as the connecting rod, applying reciprocating force to the crank. There is usually a bar perpendicular to the other end of the arm, often with a freely rotatable handle or attached.
Examples
Familiar examples include:Hand-powered cranks
- Mechanical pencil sharpener
- Fishing reel and other reels for cables, wires, ropes, etc.
- Starting Handle for older cars
- Manually operated car window
- The carpenter's brace is a compound crank.
- The crank set that drives a handcycle through its handles.
- Hand winches
Foot-powered cranks
- The crankset that drives a bicycle via the pedals.
- Treadle sewing machine
Engines
History
Western World
Classical Antiquity
The handle of the rotary handmill which appeared in 5th century BC Celtiberian Spain and ultimately reached Greece by the first century BCE. A Roman iron crankshaft of yet unknown purpose dating to the 2nd century AD was excavated in Augusta Raurica, Switzerland. The 82.5 cm long piece has fitted to one end a 15 cm long bronze handle, the other handle being lost.A ca. 40 cm long true iron crank was excavated, along with a pair of shattered mill-stones of 50−65 cm diameter and diverse iron items, in Aschheim, close to Munich. The crank-operated Roman mill is dated to the late 2nd century AD. An often cited modern reconstruction of a bucket-chain pump driven by hand-cranked flywheels from the Nemi ships has been dismissed though as "archaeological fantasy".
, the earliest known machine to combine a crank with a connecting rod.
The earliest evidence for the crank combined with a connecting rod in a machine appears in the Roman Hierapolis sawmill in Asia Minor from the 3rd century AD and two Roman stone sawmills at Gerasa, Roman Syria, and Ephesus, Asia Minor. On the pediment of the Hierapolis mill, a waterwheel fed by a mill race is shown powering via a gear train two frame saws which cut rectangular blocks by the way of some kind of connecting rods and, through mechanical necessity, cranks. The accompanying inscription is in Greek.
The crank and connecting rod mechanisms of the other two archaeologically attested sawmills worked without a gear train. In ancient literature, there is a reference to the workings of water-powered marble saws close to Trier, now Germany, by the late 4th century poet Ausonius; about the same time, these mill types seem also to be indicated by the Christian saint Gregory of Nyssa from Anatolia, demonstrating a diversified use of water-power in many parts of the Roman Empire The three finds push back the date of the invention of the crank and connecting rod by a full millennium:
Middle Ages
A rotary grindstone − the earliest representation thereof − which is operated by a crank handle is shown in the Carolingian manuscript Utrecht Psalter; the pen drawing of around 830 goes back to a late antique original. A musical tract ascribed to the abbot Odo of Cluny describes a fretted stringed instrument which was sounded by a resined wheel turned with a crank; the device later appears in two 12th century illuminated manuscripts. There are also two pictures of Fortuna cranking her wheel of destiny from this and the following century.The use of crank handles in trepanation drills was depicted in the 1887 edition of the Dictionnaire des Antiquités Grecques et Romaines to the credit of the Spanish Muslim surgeon Abu al-Qasim al-Zahrawi; however, the existence of such a device cannot be confirmed by the original illuminations and thus has to be discounted. The Benedictine monk Theophilus Presbyter described crank handles "used in the turning of casting cores".
The Italian physician Guido da Vigevano, planning for a new crusade, made illustrations for a paddle boat and war carriages that were propelled by manually turned compound cranks and gear wheels. The Luttrell Psalter, dating to around 1340, describes a grindstone which was rotated by two cranks, one at each end of its axle; the geared hand-mill, operated either with one or two cranks, appeared later in the 15th century;
Medieval cranes were occasionally powered by cranks, although more often by windlasses.
Renaissance
The crank became common in Europe by the early 15th century, often seen in the works of those such as the German military engineer Konrad Kyeser. Devices depicted in Kyeser's Bellifortis include cranked windlasses for spanning siege crossbows, cranked chain of buckets for water-lifting and cranks fitted to a wheel of bells. Kyeser also equipped the Archimedes screws for water-raising with a crank handle, an innovation which subsequently replaced the ancient practice of working the pipe by treading. The earliest evidence for the fitting of a well-hoist with cranks is found in a miniature of c. 1425 in the German Hausbuch of the Mendel Foundation.The first depictions of the compound crank in the carpenter's brace appear between 1420 and 1430 in various northern European artwork. The rapid adoption of the compound crank can be traced in the works of the Anonymous of the Hussite Wars, an unknown German engineer writing on the state of the military technology of his day: first, the connecting-rod, applied to cranks, reappeared, second, double compound cranks also began to be equipped with connecting-rods and third, the flywheel was employed for these cranks to get them over the 'dead-spot'.
One of the drawings of the Anonymous of the Hussite Wars shows a boat with a pair of paddle-wheels at each end turned by men operating compound cranks. The concept was much improved by the Italian engineer and writer Roberto Valturio in 1463, who devised a boat with five sets, where the parallel cranks are all joined to a single power source by one connecting-rod, an idea also taken up by his compatriot Francesco di Giorgio.
In Renaissance Italy, the earliest evidence of a compound crank and connecting-rod is found in the sketch books of Taccola, but the device is still mechanically misunderstood. A sound grasp of the crank motion involved demonstrates a little later Pisanello who painted a piston-pump driven
by a water-wheel and operated by two simple cranks and two connecting-rods.
The 15th century also saw the introduction of cranked rack-and-pinion devices, called cranequins, which were fitted to the crossbow's stock as a means of exerting even more force while spanning the missile weapon. In the textile industry, cranked reels for winding skeins of yarn were introduced.
Around 1480, the early medieval rotary grindstone was improved with a treadle and crank mechanism. Cranks mounted on push-carts first appear in a German engraving of 1589.
From the 16th century onwards, evidence of cranks and connecting rods integrated into machine design becomes abundant in the technological treatises of the period: Agostino Ramelli's The Diverse and Artifactitious Machines of 1588 alone depicts eighteen examples, a number which rises in the Theatrum Machinarum Novum by Georg Andreas Böckler to 45 different machines, one third of the total.
Far East
It was thought that evidence of the earliest true crank handle was found in a Han era glazed-earthenware tomb model of a agricultural winnowing fan dated no later than 200 AD, but since then a series of similar pottery models with crank operated winnowing fans were unearthed, with one of them dating back to the Western Han dynasty. Historian Lynn White stated that the Chinese crank was 'not given the impulse to change reciprocating to circular motion in other contrivances', citing one reference to a Chinese crank-and-connecting rod dating to 1462. However, later publications reveal that the Chinese used not just the crank, but the crank-and-connecting rod for operating querns as far back as the Western Han dynasty as well. Eventually crank-and-connecting rods were used in the inter-conversion or rotary and reciprocating motion for other applications such as flour-sifting, treadle spinning wheels, water powered furnace bellows, and silk-reeling machines.Middle East
The crank appears in the mid-9th century in several of the hydraulic devices described by the Banū Mūsā brothers in their Book of Ingenious Devices. These devices, however, made only partial rotations and could not transmit much power, although only a small modification would have been required to convert it to a crankshaft.Al-Jazari described a crank and connecting rod system in a rotating machine in two of his water-raising machines. His twin-cylinder pump incorporated a crankshaft. After al-Jazari cranks in Islamic technology are not traceable until an early 15th century copy of the Mechanics of the ancient Greek engineer Hero of Alexandria.
20th century
Cranks were formerly common on some machines in the early 20th century; for example almost all phonographs before the 1930s were powered by clockwork motors wound with cranks. Reciprocating piston engines use cranks to convert the linear piston motion into rotational motion. Internal combustion engines of early 20th century automobiles were usually started with hand cranks, before electric starters came into general use. The last car model which incorporated a crank was the Citroën 2CV 1948-1990The 1918 Reo owner's manual describes how to hand crank the automobile:
- First: Make sure the gear shifting lever is in neutral position.
- Second: The clutch pedal is unlatched and the clutch engaged. The brake pedal is pushed forward as far as possible setting brakes on the rear wheel.
- Third: See that spark control lever, which is the short lever located on top of the steering wheel on the right side, is back as far as possible toward the driver and the long lever, on top of the steering column controlling the carburetor, is pushed forward about one inch from its retarded position.
- Fourth: Turn ignition switch to point marked "B" or "M"
- Fifth: Set the carburetor control on the steering column to the point marked "START." Be sure there is gasoline in the carburetor. Test for this by pressing down on the small pin projecting from the front of the bowl until the carburetor floods. If it fails to flood it shows that the fuel is not being delivered to the carburetor properly and the motor cannot be expected to start. See instructions on page 56 for filling the vacuum tank.
- Sixth: When it is certain the carburetor has a supply of fuel, grasp the handle of starting crank, push in endwise to engage ratchet with crank shaft pin and turn over the motor by giving a quick upward pull. Never push down, because if for any reason the motor should kick back, it would endanger the operator.
Crank axle