Task state segment
The task state segment is a structure on x86-based computers which holds information about a task. It is used by the operating system kernel for task management. Specifically, the following information is stored in the TSS:
- Processor register state
- [|I/O port permissions]
- Inner-level stack pointers
- Previous TSS link
Location of the TSS
The TSS may reside anywhere in memory. A segment register called the task register holds a segment selector that points to a valid TSS segment descriptor which resides in the GDT. Therefore, to use a TSS the following must be done by the operating system kernel:- Create a TSS descriptor entry in the GDT
- Load the TR with the segment selector for that segment
- Add information to the TSS in memory as needed
Task register
The TR register is a 16-bit register which holds a segment selector for the TSS. It may be loaded through the LTR instruction. LTR is a privileged instruction and acts in a manner similar to other segment register loads. The task register has two parts: a portion visible and accessible by the programmer and an invisible one that is automatically loaded from the TSS descriptor.Register states
The TSS may contain saved values of all the x86 registers. This is used for task switching. The operating system may load the TSS with the values of the registers that the new task needs and after executing a hardware task switch the x86 CPU will load the saved values from the TSS into the appropriate registers. Note that some modern operating systems such as Windows and Linux do not use these fields in the TSS as they implement software task switching.Note that during a hardware task switch, certain fields of the old TSS are updated with the CPU's current register contents before the values from the new TSS are read. Thus some TSS fields are read/write, while others are read-only:
- Read/Write fields: read and written during a hardware task switch.
- * All general-purpose registers ;
- * All segment registers ;
- * Current execution state ;
- * The
Linkfield in the new TSS, if the task switch was due to aCALLorINTrather than aJMP. - Read-only fields: read only when required, as indicated.
- * Control Register 3, also known as the Page Directory Base Register.
- *: Read during a hardware task switch.
- * The Local Descriptor Table register ;
- *: Read during a hardware task switch.
- * The three privilege-level stack pairs ;
- *: Read during an inter-level
CALLorINTto establish a new stack. - * The IO Port Bitmap pointer and the I/O Port Bitmap itself;
- *: Read during an
IN,OUT,INSorOUTSinstruction ifCPL > IOPLto confirm the instruction is legal.
PDBR field is in fact the very first one read out of the new TSS: since a hardware task switch can also switch to a completely different page table mapping, all the other fields are relative to the new mapping.I/O port permissions
The TSS contains a 16-bit pointer to I/O port permissions bitmap for the current task. This bitmap, usually set up by the operating system when a task is started, specifies individual ports to which the program should have access. The I/O bitmap is a bit array of port access permissions; if the program has permission to access a port, a "0" is stored at the corresponding bit index, and if the program does not have permission, a "1" is stored there. If the TSS’ segment limit is less than the full bitmap, all missing bits are assumed to be "1".The feature operates as follows: when a program issues an x86 I/O port instruction such as IN or OUT, the hardware will do an I/O privilege level check to see if the program has access to all I/O ports. If the Current Privilege Level of the program is numerically greater than the I/O Privilege level , the program does not have I/O port access to all ports. The hardware will then check the I/O permissions bitmap in the TSS to see if that program can access the specific port in the IN or OUT instruction. If relevant bit in the I/O port permissions bitmap is/are clear, the program is allowed access to the port, and the instruction is allowed to execute. If the relevant bit is/are set - or if the bit is/are past the TSS’ segment limit - the program does not have access and the processor generates a general protection fault. This feature allows operating systems to grant selective port access to user programs.
Inner-level stack pointers
The TSS contains 6 fields for specifying the new stack pointer when a privilege level change happens. The field SS0 contains the stack segment selector for CPL=0, and the field ESP0/RSP0 contains the new ESP/RSP value for CPL=0. When an interrupt happens in protected mode, the x86 CPU will look in the TSS for SS0 and ESP0 and load their values into SS and ESP respectively. This allows for the kernel to use a different stack than the user program, and also have this stack be unique for each user program.A new feature introduced in the AMD64 extensions is called the Interrupt Stack Table, which also resides in the TSS and contains logical stack pointers. If an interrupt descriptor table specifies an IST entry to use, the processor will load the new stack from the IST instead. This allows known-good stacks to be used in case of serious errors. Previously, the entry for the exception or interrupt in the IDT pointed to a task gate, causing the processor to switch to the task that is pointed by the task gate. The original register values were saved in the TSS current at the time the interrupt or exception occurred. The processor then set the registers, including SS:ESP, to a known value specified in the TSS and saved the selector to the previous TSS. The problem here is that hardware task switching is not supported on AMD64.
Previous TSS link
This is a 16-bit selector which allows linking this TSS with the previous one. This is only used for hardware task switching. See the IA-32 manuals for details.Use of TSS in Linux
Although a TSS could be created for each task running on the computer, Linux kernel only creates one TSS for each CPU and uses them for all tasks. This approach was selected as it provides easier portability to other architectures, and improved performance and flexibility. Linux only uses the I/O port permission bitmap and inner stack features of the TSS; the other features are only needed for hardware task switches, which the Linux kernel does not use.Exceptions related to the TSS
The x86 exception vector 10 is called the Invalid TSS exception. It is issued by the processor whenever something goes wrong with the TSS access. For example, if an interrupt happens in CPL=3 and is transferring control to CPL=0, the TSS is used to extract SS0 and ESP0/RSP0 for the stack switch. If the task register holds a bad TSS selector, a #TS fault will be generated. The Invalid TSS exception should never happen during normal operating system operation and is always related to kernel bugs or hardware failure.For more details on TSS exceptions, see Volume 3a, Chapter 6 of the IA-32 manual.
TSS in x86-64 mode
The x86-64 architecture does not support hardware task switches. However the TSS can still be used in a machine running in the 64 bit extended modes. In these modes the TSS is still useful as it stores:- The stack pointer addresses for each privilege level.
- Pointer Addresses for the Interrupt Stack Table.
- Offset Address of the IO permission bitmap.