Thermal oxidizer
A thermal oxidizer is a process unit for air pollution control in many chemical plants that decomposes hazardous gases at a high temperature and releases them into the atmosphere.
Principle
Thermal oxidizers are typically used to destroy hazardous air pollutants and volatile organic compounds from industrial air streams. These pollutants are generally hydrocarbon based and when destroyed via thermal combustion they are chemically oxidized to form CO2 and H2O. Three main factors in designing the effective thermal oxidizers are temperature, residence time, and turbulence. The temperature needs to be high enough to ignite the waste gas. Most organic compounds ignite at the temperature between and. To ensure near destruction of hazardous gases, most basic oxidizers are operated at much higher temperature levels. When catalyst is used, the operating temperature range may be lower. Residence time is to ensure that there is enough time for the combustion reaction to occur. The turbulence factor is the mixture of combustion air with the hazardous gases.Technologies
Direct fired thermal oxidizer - afterburner
The simplest technology of thermal oxidation is direct-fired thermal oxidizer. A process stream with hazardous gases is introduced into a firing box through or near the burner and enough residence time is provided to get the desired destruction removal efficiency of the VOCs. Most direct-fired thermal oxidizers operate at temperature levels between and with air flow rates of 0.24 to 24 standard cubic meters per second.Also called afterburners in the cases where the input gases come from a process where combustion is incomplete, these systems are the least capital intensive, and can be integrated with downstream boilers and heat exchangers to optimize fuel efficiency. Thermal Oxidizers are best applied where there is a very high concentration of VOCs to act as the fuel source for complete combustion at the targeted operating temperature.
Regenerative thermal oxidizer (RTO)
One of today's most widely accepted air pollution control technologies across industry is a regenerative thermal oxidizer, commonly referred to as a RTO. RTOs use a ceramic bed which is heated from a previous oxidation cycle to preheat the input gases to partially oxidize them. The preheated gases enter a combustion chamber that is heated by an external fuel source to reach the target oxidation temperature which is in the range between and. The final temperature may be as high as for applications that require maximum destruction. The air flow rates are 2.4 to 240 standard cubic meters per second.RTOs are very versatile and extremely efficient – thermal efficiency can reach 95%. They are regularly used for abating solvent fumes, odours, etc. from a wide range of industries. Regenerative Thermal Oxidizers are ideal in a range of low to high VOC concentrations up to 10 g/m3 solvent. There are currently many types Regenerative Thermal Oxidizer on the market with the capability of 99.5+% Volatile Organic Compound oxidization or destruction efficiency. The ceramic heat exchanger in the towers can be designed for thermal efficiencies as high as 97+%.
Ventilation air methane thermal oxidizer (VAMTOX)
Ventilation air methane thermal oxidizers are used to destroy methane in the exhaust air of underground coal mine shafts. Methane is a greenhouse gas and, when oxidized via thermal combustion, is chemically altered to form CO2 and H2O. CO2 is 25 times less potent than methane when emitted into the atmosphere with regards to global warming. Concentrations of methane in mine ventilation exhaust air of coal and trona mines are very dilute; typically below 1% and often below 0.5%. VAMTOX units have a system of valves and dampers that direct the air flow across one or more ceramic filled bed. On start-up, the system preheats by raising the temperature of the heat exchanging ceramic material in the bed at or above the auto-oxidation temperature of methane, at which time the preheating system is turned off and mine exhaust air is introduced. Then the methane-filled air reaches the preheated bed, releasing the heat from combustion. This heat is then transferred back to the bed, thereby maintaining the temperature at or above what is necessary to support auto-thermal operation.Thermal recuperative oxidizer
A less commonly used thermal oxidizer technology is a thermal recuperative oxidizer. Thermal recuperative oxidizers have a primary and/or secondary heat exchanger within the system. A primary heat exchanger preheats the incoming dirty air by recuperating heat from the exiting clean air. This is done by a shell and tube heat exchanger or a plate heat exchanger. As the incoming air passes on one side of the metal tube or plate, hot clean air from the combustion chamber passes on the other side of the tube or plate and heat is transferred to the incoming air through the process of conduction using the metal as the medium of heat transfer. In a secondary heat exchanger the same concept applies for heat transfer, but the air being heated by the outgoing clean process stream is being returned to another part of the plant – perhaps back to the process.Biomass fired thermal oxidizer
, such as wood chips, can be used as the fuel for a thermal oxidizer. The biomass is then gasified and the stream with hazardous gases is mixed with the biomass gas in a firing box. Sufficient turbulence, retention time, oxygen content and temperature will ensure destruction of the VOC's. Such biomass fired thermal oxidizer has been installed at Warwick Mills, New Hampshire. The inlet concentrations are between 3000–10.000 ppm VOC. The outlet concentration of VOC are below 3 ppm, thus having a VOC destruction efficiency of 99.8–99.9%.Flameless thermal oxidizer (FTO)
In a flameless thermal oxidizer system waste gas, ambient air, and auxiliary fuel are premixed prior to passing the combined gaseous mixture through a preheated inert ceramic media bed. Through the transfer of heat from the ceramic media to the gaseous mixture the organic compounds in the gas are oxidized to innocuous byproducts, i.e., carbon dioxide and water vapor while also releasing heat into the ceramic media bed.The gas mixture temperature is kept below the lower flammability limit based on the percentages of each organic species present. Flameless thermal oxidizers are designed to operate safely and reliably below the composite LFL while maintaining a constant operating temperature. Waste gas streams experience multiple seconds of residence time at high temperatures leading to measured destruction removal efficiencies that exceed 99.9999%. Premixing all of the gases prior to treatment eliminates localized high temperatures which leads to thermal NOx typically below 2 ppmV. Flameless thermal oxidizer technology was originally developed at the U.S. Department of Energy to more efficiently convert energy in burners, process heaters, and other thermal systems.
Catalytic oxidizer
Catalytic oxidizer is another category of oxidation systems that is similar to typical thermal oxidizers, but the catalytic oxidizers use a catalyst to promote the oxidation. Catalytic oxidation occurs through a chemical reaction between the VOC hydrocarbon molecules and a precious-metal catalyst bed that is internal to the oxidizer system. A catalyst is a substance that is used to accelerate the rate of a chemical reaction, allowing the reaction to occur in a normal temperature range between and.Regenerative catalytic oxidizer (RCO)
The catalyst can be used in a Regenerative Thermal Oxidizer to allow lower operating temperatures. This is also called Regenerative Catalytic Oxidizer or RCO. For example, the thermal ignition temperature of carbon monoxide is normally. By utilizing a suitable oxidation catalyst, the ignition temperature can be reduced to around.This can result in lower operating costs than a RTO. Most systems operate within the to degree range. Some systems are designed to operate both as RCOs and RTOs. When these systems are used special design considerations are utilized to reduce the probability of overheating, as these high temperatures would deactivate the catalyst, e.g. by sintering of the active material.