Three-two pull down is a term used in filmmaking and television production for the post-production process of transferring film to video. It converts 24 frames per second into 29.97 frames per second. Roughly speaking, converting every 4 frames into 5 frames plus a slight slow down in speed. Film runs at a standard rate of 24 frames per second, whereasNTSCvideo has a signal frame rate of 29.97 frames per second. Every interlaced videoframe has two fields for each frame. The three-two pull down is where the telecine adds a third video field to every second video frame, but the untrained eye cannot see the addition of this extra video field. In the figure, the film frames A-D are true or original images since they have been photographed as a complete frame. The A, B, and D frames on the right in the NTSC footage are original frames. The third and fourth frames have been created by blending movie fields from different frames.
Video
2:3
In the United States and other countries where television uses the 59.94 Hz vertical scanning frequency, video is broadcast at 29.97 frame/s. For the film's motion to be accurately rendered on the video signal, a telecine must use a technique called the 2:3 pull down to convert from 24 to 29.97 frame/s. The term “pulldown” comes from the mechanical process of “pulling” the film downward within the film portion of the transport mechanism, to advance it from one frame to the next at a repetitive rate. This is accomplished in two steps. The first step is to slow down the film motion by 1/1000 to 23.976 frames/s. The difference in speed is imperceptible to the viewer. For a two-hour film, play time is extended by 7.2 seconds. The second step of the 2:3 pulldown is distributing cinema frames into video fields. At 23.976 frame/s, there are four frames of film for every five frames of 29.97 Hz video: These four frames needs to be “stretched” into five frames by exploiting the interlaced nature of video. Since an interlaced video frame is made up of two incomplete fields, conceptually four frames need to be used in ten fields. The term "2:3" comes from the pattern for producing fields in the new video frames. The pattern of 2-3 is an abbreviation of the actual pattern of 2-3-2-3, which indicates that the first film frame is used in 2 fields, the second film frame is used in 3 fields, the third film frame is used in 2 fields, and the fourth film frame is used in 3 fields—producing a total of 10 fields, or 5 video frames. If the four film frames are called A, B, C and D, the five video frames produces are A1-A2, B1-B2, B2-C1, C2-D1 and D2-D2. That is, frame A is used 2 times ; frame B is used 3 times ; frame C is used 2 times ; and frame D is used 3 times. The 2-3-2-3 cycle repeats itself completely after four film frames have been exposed.
3:2
The alternative "3:2" pattern is similar to the one shown above, except it is shifted by one frame. For instance, a cycle that starts with film frame B yields a 3:2 pattern: B1-B2, B2-C1, C2-D1, D2-D2, A1-A2 or 3-2-3-2 or simply 3-2. In other words, there is no difference between the 2-3 and 3-2 patterns. In fact, the "3-2" notation is misleading because according to SMPTE standards for every four-frame film sequence the first frame is scanned twice, not three times.
Modern alternatives
The above method is a "classic" 2:3, which was used before frame buffers allowed for holding more than one frame. It has the disadvantage of creating two dirty frames and three clean frames in every five video frames. The preferred method for doing a 2:3 creates only one dirty frame in every five ; while this method has a slight bit more judder, it allows for easier upconversion and a better overall compression when encoding. The 2:3:3:2 pattern is supported by the Panasonic DVX-100Bvideo camera under the name "Advanced Pulldown". Note that just fields are displayed—no frames hence no dirty frames—in interlaced display such as on a CRT. Dirty frames may appear in other methods of displaying the interlaced video.
Audio
The rate of NTSC video is 29.97 frames per second, or one-thousandth slower than 30 frame/s, due to the NTSC color encoding process which mandated that the line rate be a sub-multiple of the 3.579545 MHz color "burst" frequency, or 15734.2637 Hz, rather than the ac "line locked" line rate of 15750.0000… Hz. This seemingly odd relationship proved to be essential to eliminating moiré and other image defects. Although slight, the sync will catch up, and the audio can end up being several seconds out of sync with the image. In order to correct this error, the telecine can either pull up or pull down. A pull up will speed up the sound by 0.1%, used for transferring video to film. A pull down will slow the audio speed down by 0.1%, necessary for transferring film to video.
