In chemistry, yield, also referred to as reaction yield, is a measure of the quantity of moles of a product formed in relation to the reactant consumed, obtained in a chemical reaction, usually expressed as a percentage. Yield is one of the primary factors that scientists must consider in organic and inorganic chemical synthesis processes. In chemical reaction engineering, "yield", "conversion" and "selectivity" are terms used to describe ratios of how much of a reactant was consumed, how much desired product was formed in relation to the undesired product, represented as X, Y, and S.
Definitions
In chemical reaction engineering, "yield", "conversion" and "selectivity" are terms used to describe ratios of how much of a reactant has reacted—conversion, how much of a desired product was formed—yield, and how much desired product was formed in ratio to the undesired product—selectivity, represented as X,S, and Y. According to the Elements of Chemical Reaction Engineering manual, yield refers to the amount of a specific product formed per mole of reactant consumed. In chemistry, mole is used to describe quantities of reactants and products in chemical reactions. The Compendium of Chemical Terminology defined yield as the "atio expressing the efficiency of a mass conversion process. The yield coefficient is defined as the amount of cell mass or product formed related to the consumed substrate or to the intracellular ATP production." In the section "Calculations of yields in the monitoring of reactions" in the 1996 4th edition of Vogel's Textbook of Practical Organic Chemistry, the authors write that, "heoretical yield in an organic reaction is the weight of product which would be obtained if the reaction has proceeded to completion according to the chemical equation. The yield is the weight of the pure product which is isolated from the reaction." In 'the 1996 edition of Vogel's Textbook, percentage yield is expressed as,
According to the 1996 edition of Vogel's Textbook, yields close to 100% are called quantitative, yields above 90% are called excellent, yields above 80% are very good, yields above 70% are good, yields above 50% are fair, and yields below 40% are called poor. In their 2002 publication, Petrucci, Harwood, and Herring wrote that Vogel's Textbook names were arbitrary, and not universally accepted, and depending on the nature of the reaction in question, these expectations may be unrealistically high. Yields may appear to be 100% or above when products are impure, as the measured weight of the product will include the weight of any impurities. In their 2016 laboratory manual, Experimental Organic Chemistry, the authors described the "reaction yield" or "absolute yield" of a chemical reaction as the "amount of pure and dry product yielded in a reaction". They wrote that knowing the stoichiometry of a chemical reaction—the numbers and types of atoms in the reactants and products, in a balanced equation "make it possible to compare different elements through stoichiometric factors." Ratios obtained by these quantitative relationships are useful in data analysis.
Theoretical, actual, and percent yields
The percent yield is a comparison between the actual yield—which is the weight of the intended product of a chemical reaction in a laboratory setting—and the theoretical yield—the measurement of pure intended isolated product, based on the chemical equation of a flawless chemical reaction, and is defined as,
The ideal relationship between products and reactants in a chemical reaction can be obtained by using a chemical reaction equation. Stoichiometry is used to run calculations about chemical reactions, for example, the stoichiometric mole ratio between reactants and products. The stoichiometry of a chemical reaction is based on chemical formulas and equations that provide the quantitative relation between the number of moles of various products and reactants, including yields. Stoichiometric equations are used to determine the limiting reagent or reactant—the reactant that is completely consumed in a reaction. The limiting reagent determines the theoretical yield—the relative quantity of moles of reactants and the product formed in a chemical reaction. Other reactants are said to be present in excess. The actual yield—the quantity physically obtained from a chemical reaction conducted in a laboratory—is often less than the theoretical yield. The theoretical yield is what would be obtained if all of the limiting reagent reacted to give the product in question. A more accurate yield is measured based on how much product was actually produced versus how much could be produced. The ratio of the theoretical yield and the actual yield results in a percent yield. When more than one reactant participates in a reaction, the yield is usually calculated based on the amount of the limiting reactant, whose amount is less than stoichiometrically equivalent to the amounts of all other reactants present. Other reagents present in amounts greater than required to react with all the limiting reagent present are considered excess. As a result, the yield should not be automatically taken as a measure for reaction efficiency. In their 1992 publication General Chemistry, Whitten, Gailey, and Davis described the theoretical yield as the amount predicted by a stoichiometric calculation based on the number of moles of all reactants present. This calculation assumes that only one reaction occurs and that the limiting reactant reacts completely. According to Whitten, the actual yield is always smaller, often very much so, for several reasons. As a result, many reactions are incomplete and the reactants are not completely converted to products. If a reverse reaction occurs, the final state contains both reactants and products in a state of chemical equilibrium. Two or more reactions may occur simultaneously, so that some reactant is converted to undesired side products. Losses occur in the separation and purification of the desired product from the reaction mixture. Impurities are present in the starting material which do not react to give desired product.
The molar amount of the reactants is calculated from the weights.
Ethanol is used in a 2.5-fold excess.
The theoretical molar yield is 2.0 mol.
The molar yield of the product is calculated from its weight.
The % yield is calculated from the actual molar yield and the theoretical molar yield.
Purification of products
In his 2016 Handbook of Synthetic Organic Chemistry, Michael Pirrung wrote that yield is one of the primary factors synthetic chemists must consider in evaluating a synthetic method or a particular transformation in "multistep syntheses." He wrote that a yield based on recovered starting material or does not provide the theoretical yield or the "100% of the amount of product calculated", that is necessary in order to take the next step in the multistep systhesis. Purification steps always lower the yield, through losses incurred during the transfer of material between reaction vessels and purification apparatus or imperfect separation of the product from impurities, which may necessitate the discarding of fractions deemed insufficiently pure. The yield of the product measured after purification is called the isolated yield of the reaction.
Yields can also be calculated by measuring the amount of product formed relative to a known amount of an added internal standard, using techniques like Gas chromatography, High-performance liquid chromatography, or Nuclear magnetic resonance spectroscopy or magnetic resonance spectroscopy. A yield determined using this approach is known as an internal standard yield. Yields are typically obtained in this manner to accurately determine the quantity of product produced by a reaction, irrespective of potential isolation problems. Additionally, they can be useful when isolation of the product is challenging or tedious, or when the rapid determination of an approximate yield is desired. Unless otherwise indicated, yields reported in the synthetic organic and inorganic chemistry literature refer to isolated yields, which better reflect the amount of pure product one is likely to obtain under the reported conditions, upon repeating the experimental procedure.
Reporting of yields
In their 2010 Synlett article, Martina Wernerova and organic chemist, Tomáš Hudlický, raised concerns about inaccurate reporting of yields, and offered solutions—including the proper characterization of compounds. After performing careful control experiments, Wernerova and Hudlický said that each physical manipulation results in a loss of yield of about 2%. Thus, isolated yields measured after standard aqueous workup and chromatographic purification should seldom exceed 94%. They called this phenomenon "yield inflation" and said that yield inflation had gradually crept upward in recent decades in chemistry literature. They attributed yield inflation to careless measurement of yield on reactions conducted on small scale, wishful thinking and a desire to report higher numbers for publication purposes. Hudlický's 2020 article published in Angewandte Chemie—since retracted—honored and echoed Dieter Seebach's often-cited 1990 thirty-year review of organic synthesis, which had also been published in Angewandte Chemie. In his 2020 Angewandte Chemie 30-year review, Hudlický said that the suggestions that he and Wernerova had made in their 2020 Synlett article, were "ignored by the editorial boards of organic journals, and by most referees."
