Airbreathing jet engine


An airbreathing jet engine is a jet engine that emits a jet of hot exhaust gases formed from air that is forced into the engine by several stages of centrifugal, axial or ram compression, which is then heated and expanded through a nozzle. They are typically gas turbine engines. The majority of the mass flow through an airbreathing jet engine is provided by air taken from outside of the engine and heated internally, using energy stored in the form of fuel.
All practical airbreathing jet engines are internal combustion engines that directly heat the air by burning fuel, with the resultant hot gases used for propulsion via a propulsive nozzle, although other techniques for heating the air have been experimented with. Most modern jet engine designs are turbofans, which have largely replaced turbojets. These modern engines use a gas turbine engine core with high overall pressure ratio and high turbine entry temperature, and provide a great deal of their thrust with a turbine-powered fan stage, rather than with pure exhaust thrust as in a turbojet. These features combine to give a high efficiency, relative to a turbojet. A few jet engines use simple ram effect or pulse combustion to give compression.

Background

The original air-breathing gas turbine jet engine was the turbojet. It was a concept brought to life by two engineers, Frank Whittle in England UK and Hans von Ohain in Germany. The turbojet compresses and heats air and then exhausts it as a high speed, high temperature jet to create thrust. While these engines are capable of giving high thrust levels, they are most efficient at very high speeds, due to the low-mass-flow, high speed nature of the jet exhaust.
Modern turbofans are a development of the turbojet; they are basically a turbojet that includes a new section called the fan stage. Rather than using all of its exhaust gases to provide direct thrust like a turbojet, the turbofan engine extracts some of the power from the exhaust gases inside the engine and uses it to power the fan stage. The fan stage accelerates a large volume of air through a duct, bypassing the engine core, and expelling it at the rear as a jet, creating thrust. A proportion of the air that comes through the fan stage enters the engine core rather than being ducted to the rear, and is thus compressed and heated; some of the energy is extracted to power the compressors and fans, while the remainder is exhausted at the rear. This high-speed, hot-gas exhaust blends with the low speed, cool-air exhaust from the fan stage, and both contribute to the overall thrust of the engine. Depending on what proportion of cool air is bypassed around the engine core, a turbofan can be called low-bypass, high-bypass, or very-high-bypass engines.
Low bypass engines were the first turbofan engines produced, and provide the majority of their thrust from the hot core exhaust gases, while the fan stage only supplements this. These engines are still commonly seen on military fighter aircraft, since they provide more efficient thrust at supersonic speeds and have a narrower frontal area, minimizing aerodynamic drag. Their comparatively high noise levels and subsonic fuel consumption are deemed acceptable in such an application, whereas although the first generation of turbofan airliners used low-bypass engines, their high noise levels and fuel consumption mean they have fallen out of favor for large aircraft. High bypass engines have a much larger fan stage, and provide most of their thrust from the ducted air of the fan; the engine core provides power to the fan stage, and only a proportion of the overall thrust comes from the engine core exhaust stream. A high-bypass turbofan functions very similarly to a turboprop engine, except it uses a many-bladed fan rather than a multi-blade propeller, and relies on a duct to properly vector the airflow to create thrust.
Over the last several decades, there has been a move towards very high bypass engines, which use fans far larger than the engine core itself, which is typically a modern, high efficiency two or three-spool design. This high efficiency and power is what allows such large fans to be viable, and the increased thrust available, have allowed a move to large twin engine aircraft, such as the Airbus A350 or Boeing 777, as well as allowing twin engine aircraft to operate on long overwater routes, previously the domain of 3-engine or 4-engine aircraft.
Jet engines were designed to power aircraft, but have been used to power jet cars and jet boats for speed record attempts, and even for commercial uses such as by railroads for clearing snow and ice from switches in railyards, and by race tracks for drying off track surfaces after rain.

Types of airbreathing jet engines

Airbreathing jet engines are nearly always internal combustion engines that obtain propulsion from the combustion of fuel inside the engine. Oxygen present in the atmosphere is used to oxidise a fuel source, typically a hydrocarbon-based jet fuel. The burning mixture expands greatly in volume, driving heated air through a propelling nozzle.
Gas turbine powered engines:
Ram powered jet engine:
Pulsed combustion jet engine:
Two engineers, Frank Whittle in the UK and Hans von Ohain in Germany, developed the turbojet concept independently into practical engines during the late 1930s.
Turbojets consist of an inlet, a compressor, a combustor, a turbine and a propelling nozzle. The compressed air is heated in the combustor and passes through the turbine, then expands in the nozzle to produce a high speed propelling jet
Turbojets have a low propulsive efficiency below about Mach 2 and produce a lot of jet noise, both a result of the very high velocity of the exhaust. Modern jet propelled aircraft are powered by turbofans. These engines, with their lower exhaust velocities, produce less jet noise and use less fuel. Turbojets are still used to power medium range cruise missiles, due to their high exhaust speed, low frontal area and relative simplicity.

Turbofan engine

Most modern jet engines are turbofans. The low pressure compressor, usually known as a fan, compresses air into a bypass duct whilst its inner portion supercharges the core compressor. The fan is often an integral part of a multi-stage core LPC. The bypass airflow either passes to a separate 'cold nozzle' or mixes with low pressure turbine exhaust gases, before expanding through a 'mixed flow nozzle'.
In the 1960s there was little difference between civil and military jet engines, apart from the use of afterburning in some applications. Today, turbofans are used for airliners because they have an exhaust speed that is better matched to the subsonic flight speed of the airliner. At airliner flight speeds, the exhaust speed from a turbojet engine is excessively high and wastes energy. The lower exhaust speed from a turbofan gives better fuel consumption. The increased airflow from the fan gives higher thrust at low speeds. The lower exhaust speed also gives much lower jet noise.
The comparatively large frontal fan has several effects. Compared to a turbojet of identical thrust, a turbofan has a much larger air mass flow rate and the flow through the bypass duct generates a significant fraction of the thrust. The additional duct air has not been ignited which it gives it a slow speed, but no extra fuel is needed to provide this thrust. Instead, the energy is taken from the central core, which gives it also a reduced exhaust speed. The average velocity of the mixed exhaust air is thus reduced which is less wasteful of energy but reduces the top speed. Overall, a turbofan can be much more fuel efficient and quieter, and it turns out that the fan also allows greater net thrust to be available at slow speeds.
Thus civil turbofans today have a low exhaust speed to keep jet noise to a minimum and to improve fuel efficiency. Consequently, the bypass ratio is relatively high, with the Rolls-Royce Trent XWB approaching 10:1. Only a single fan stage is required, because a low specific thrust implies a low fan pressure ratio.
Turbofans in civilian aircraft usually have a pronounced large front area to accommodate a very large fan, as their design involves a much larger mass of air bypassing the core so they can benefit from these effects, while in military aircraft, where noise and efficiency are less important compared to performance and drag, a smaller amount of air typically bypasses the core. Turbofans designed for subsonic civilian aircraft also usually have a just a single front fan, because their additional thrust is generated by a large additional mass of air which is only moderately compressed, rather than a smaller amount of air which is greatly compressed.
Military turbofans, however, have a relatively high specific thrust, to maximize the thrust for a given frontal area, jet noise being of less concern in military uses relative to civil uses. Multistage fans are normally needed to reach the relatively high fan pressure ratio needed for high specific thrust. Although high turbine inlet temperatures are often employed, the bypass ratio tends to be low, usually significantly less than 2.0.

Turboprop and turboshaft

engines are jet engine derivatives, still gas turbines, that extract work from the hot-exhaust jet to turn a rotating shaft, which is then used to produce thrust by some other means. While not strictly jet engines in that they rely on an auxiliary mechanism to produce thrust, turboprops are very similar to other turbine-based jet engines, and are often described as such.
In turboprop engines, a portion of the engine's thrust is produced by spinning a propeller, rather than relying solely on high-speed jet exhaust. Producing thrust both ways, turboprops are occasionally referred to as a type of hybrid jet engine. They differ from turbofans in that a traditional propeller, rather than a ducted fan, provides the majority of thrust. Most turboprops use gear-reduction between the turbine and the propeller. , but they are less common. The hot-jet exhaust is an important minority of thrust, and maximum thrust is obtained by matching the two thrust contributions. Turboprops generally have better performance than turbojets or turbofans at low speeds where propeller efficiency is high, but become increasingly noisy and inefficient at high speeds.
Turboshaft engines are very similar to turboprops, differing in that nearly all energy in the exhaust is extracted to spin the rotating shaft, which is used to power machinery rather than a propeller, they therefore generate little to no jet thrust and are often used to power helicopters.

Propfan

A propfan engine is a jet engine that uses its gas generator to power an exposed fan, similar to turboprop engines. Like turboprop engines, propfans generate most of their thrust from the propeller and not the exhaust jet. The primary difference between turboprop and propfan design is that the propeller blades on a propfan are highly swept to allow them to operate at speeds around Mach 0.8, which is competitive with modern commercial turbofans. These engines have the fuel efficiency advantages of turboprops with the performance capability of commercial turbofans. While significant research and testing has been conducted on propfans, none have entered production.

Major components

Major components of a turbojet including references to turbofans, turboprops and turboshafts:

Cold Section

The various components named above have constraints on how they are put together to generate the most efficiency or performance. The performance and efficiency of an engine can never be taken in isolation; for example fuel/distance efficiency of a supersonic jet engine maximises at about mach 2, whereas the drag for the vehicle carrying it is increasing as a square law and has much extra drag in the transonic region. The highest fuel efficiency for the overall vehicle is thus typically at Mach ~0.85.
For the engine optimisation for its intended use, important here is air intake design, overall size, number of compressor stages, fuel type, number of exhaust stages, metallurgy of components, amount of bypass air used, where the bypass air is introduced, and many other factors. An example is design of the air intake.

Operation

Engine cycle

The thermodynamics of a typical air-breathing jet engine are modeled approximately by a Brayton Cycle which is a thermodynamic cycle that describes the workings of the gas turbine engine, which is the basis of the airbreathing jet engine and others. It is named after George Brayton, the American engineer who developed it, although it was originally proposed and patented by Englishman John Barber in 1791. It is also sometimes known as the Joule cycle.

Thrust lapse

The nominal net thrust quoted for a jet engine usually refers to the Sea Level Static condition, either for the International Standard Atmosphere or a hot day condition. As an example, the GE90-76B has a take-off static thrust of 76,000 lbf at SLS, ISA+15 °C.
Naturally, net thrust will decrease with altitude, because of the lower air density. There is also, however, a flight speed effect.
Initially as the aircraft gains speed down the runway, there will be little increase in nozzle pressure and temperature, because the ram rise in the intake is very small. There will also be little change in mass flow. Consequently, nozzle gross thrust initially only increases marginally with flight speed. However, being an air breathing engine there is a penalty for taking on-board air from the atmosphere. This is known as ram drag. Although the penalty is zero at static conditions, it rapidly increases with flight speed causing the net thrust to be eroded.
As flight speed builds up after take-off, the ram rise in the intake starts to have a significant effect upon nozzle pressure/temperature and intake airflow, causing nozzle gross thrust to climb more rapidly. This term now starts to offset the still increasing ram drag, eventually causing net thrust to start to increase. In some engines, the net thrust at say Mach 1.0, sea level can even be slightly greater than the static thrust. Above Mach 1.0, with a subsonic inlet design, shock losses tend to decrease net thrust, however a suitably designed supersonic inlet can give a lower reduction in intake pressure recovery, allowing net thrust to continue to climb in the supersonic regime.

Safety and reliability

Jet engines are usually very reliable and have a very good safety record. However, failures do sometimes occur.

Engine surge

In some cases in jet engines the conditions in the engine due to airflow entering the engine or other variations can cause the compressor blades to stall. When this occurs the pressure in the engine blows out past the blades, and the stall is maintained until the pressure has decreased, and the engine has lost all thrust. The compressor blades will then usually come out of stall, and re-pressurize the engine. If conditions are not corrected, the cycle will usually repeat. This is called surge. Depending on the engine this can be highly damaging to the engine and creates worrying vibrations for the crew.

Blade containment

Fan, compressor or turbine blade failures have to be contained within the engine casing. To do this the engine has to be designed to pass blade containment tests as specified by certification authorities.

Bird ingestion

Bird ingestion is the term used when birds enter the intake of a jet engine. It is a common aircraft safety hazard and has caused fatal accidents. In 1988 an Ethiopian Airlines Boeing 737 ingested pigeons into both engines during take-off and then crashed in an attempt to return to the Bahir Dar airport; of the 104 people aboard, 35 died and 21 were injured. In another incident in 1995, a Dassault Falcon 20 crashed at a Paris airport during an emergency landing attempt after ingesting lapwings into an engine, which caused an engine failure and a fire in the airplane fuselage; all 10 people on board were killed.
Jet engines have to be designed to withstand the ingestion of birds of a specified weight and number, and to not lose more than a specified amount of thrust. The weight and numbers of birds that can be ingested without hazarding the safe flight of the aircraft are related to the engine intake area. In 2009, an Airbus A320 aircraft, US Airways Flight 1549, ingested one Canada goose into each engine. The plane ditched in the Hudson River after taking off from LaGuardia International Airport in New York City. There were no fatalities. The incident illustrated the hazards of ingesting birds beyond the "designed-for" limit.
The outcome of an ingestion event and whether it causes an accident, be it on a small fast plane, such as military jet fighters, or a large transport, depends on the number and weight of birds and where they strike the fan blade span or the nose cone. Core damage usually results with impacts near the blade root or on the nose cone.
Few birds fly high, so the greatest risk of a bird ingestion is during takeoff and landing and during low level flying.

Volcanic ash

If a jet plane is flying through air contaminated with volcanic ash, there is risk that ingested ash will cause erosion damage to the compressor blades, blockage of fuel nozzle air holes and blockage of the turbine cooling passages. Some of these effects may cause the engine to surge or flame-out during the flight. Re-lights are usually successful after flame-outs but with considerable loss of altitude. It was the case of British Airways Flight 9 which flew through volcanic dust at 37,000 ft. All 4 engines flamed out and re-light attempts were successful at about 13,000 ft.

Uncontained failures

One class of failure that has caused accidents is the uncontained failure, where rotating parts of the engine break off and exit through the case. These high energy parts can cut fuel and control lines, and can penetrate the cabin. Although fuel and control lines are usually duplicated for reliability, the crash of United Airlines Flight 232 was caused when hydraulic fluid lines for all three independent hydraulic systems were simultaneously severed by shrapnel from an uncontained engine failure. Prior to the United 232 crash, the probability of a simultaneous failure of all three hydraulic systems was considered as high as a billion-to-one. However, the statistical models used to come up with this figure did not account for the fact that the number-two engine was mounted at the tail close to all the hydraulic lines, nor the possibility that an engine failure would release many fragments in many directions. Since then, more modern aircraft engine designs have focused on keeping shrapnel from penetrating the cowling or ductwork, and have increasingly utilized high-strength composite materials to achieve the required penetration resistance while keeping the weight low.

Economic considerations

In 2007 the cost of jet fuel, while highly variable from one airline to another, averaged 26.5% of total operating costs, making it the single largest operating expense for most airlines.

Environmental considerations

Jet engines are usually run on fossil fuels and are thus a source of carbon dioxide in the atmosphere. Jet engines can also run on biofuels or hydrogen, although hydrogen is usually produced from fossil fuels.
About 7.2% of the oil used in 2004 was consumed by jet engines.
Some scientists believe that jet engines are also a source of global dimming due to the water vapour in the exhaust causing cloud formations.
Nitrogen compounds are also formed during the combustion process from reactions with atmospheric nitrogen. At low altitudes this is not thought to be especially harmful, but for supersonic aircraft that fly in the stratosphere some destruction of ozone may occur.
Sulphates are also emitted if the fuel contains sulphur.

Advanced designs

Ramjet

A ramjet is a form of airbreathing jet engine using the engine's forward motion to compress incoming air, without a rotary compressor. Ramjets cannot produce thrust at zero airspeed and thus cannot move an aircraft from a standstill. Ramjets require considerable forward speed to operate well, and as a class work most efficiently at speeds around Mach 3. This type of jet can operate up to speeds of Mach 6.
They consist of three sections; an inlet to compress incoming air, a combustor to inject and combust fuel, and a nozzle to expel the hot gases and produce thrust. Ramjets require a relatively high speed to efficiently compress the incoming air, so ramjets cannot operate at a standstill and they are most efficient at supersonic speeds. A key trait of ramjet engines is that combustion is done at subsonic speeds. The supersonic incoming air is dramatically slowed through the inlet, where it is then combusted at the much slower, subsonic, speeds. The faster the incoming air is, however, the less efficient it becomes to slow it to subsonic speeds. Therefore, ramjet engines are limited to approximately Mach 5.
Ramjets can be particularly useful in applications requiring a small and simple engine for high speed use, such as missiles, while weapon designers are looking to use ramjet technology in artillery shells to give added range: it is anticipated that a 120-mm mortar shell, if assisted by a ramjet, could attain a range of. They have also been used successfully, though not efficiently, as tip jets on helicopter rotors.
Ramjets are frequently confused with pulsejets, which use an intermittent combustion, but ramjets employ a continuous combustion process, and are a quite distinct type of jet engine.

Scramjets

Scramjets are an evolution of ramjets that are able to operate at much higher speeds than any other kind of airbreathing engine. They share a similar structure with ramjets, being a specially shaped tube that compresses air with no moving parts through ram-air compression. They consist of an inlet, a combustor, and a nozzle. The primary difference between ramjets and scramjets is that scramjets do not slow the oncoming airflow to subsonic speeds for combustion. Thus, scramjets do not have the diffuser required by ramjets to slow the incoming airflow to subsonic speeds. They use supersonic combustion instead and the name "scramjet" comes from "Supersonic Combusting Ramjet."
Scramjets start working at speeds of at least Mach 4, and have a maximum useful speed of approximately Mach 17. Due to aerodynamic heating at these high speeds, cooling poses a challenge to engineers.
Since scramjets use supersonic combustion they can operate at speeds above Mach 6 where traditional ramjets are too inefficient. Another difference between ramjets and scramjets comes from how each type of engine compresses the oncoming airflow: while the inlet provides most of the compression for ramjets, the high speeds at which scramjets operate allow them to take advantage of the compression generated by shock waves, primarily oblique shocks.
Very few scramjet engines have ever been built and flown. In May 2010 the Boeing X-51 set the endurance record for the longest scramjet burn at over 200 seconds.

P&W J58 Mach 3+ afterburning turbojet

Turbojet operation over the complete flight envelope from zero to Mach 3+ requires features to allow the compressor to function properly at the high inlet temperatures beyond Mach 2.5 as well as at low flight speeds.
The J58 compressor solution was to bleed airflow from the 4th compressor stage at speeds above about Mach 2. The bleed flow, 20% at Mach 3, was returned to the engine via 6 external tubes to cool the afterburner liner and primary nozzle as well as to provide extra air for combustion. The J58 engine was the only operational turbojet engine, being designed to operate continuously even at maximum afterburning, for Mach 3.2 cruise.
An alternative solution is seen in a contemporary installation, which did not reach operational status, the Mach 3 GE YJ93/XB-70. It used a variable stator compressor. Yet another solution was specified in a proposal for a Mach 3 reconnaissance Phantom. This was pre-compressor cooling, albeit available for relatively short duration.

Hydrogen-fuelled air-breathing jet engines

Jet engines can be run on almost any fuel. Hydrogen is a highly desirable fuel, as, although the energy per mole is not unusually high, the molecule is very much lighter than other molecules. The energy per kg of hydrogen is twice that of more common fuels and this gives twice the specific impulse. In addition, jet engines running on hydrogen are quite easy to build—the first ever turbojet was run on hydrogen. Also, although not duct engines, hydrogen-fueled rocket engines have seen extensive use.
However, in almost every other way, hydrogen is problematic. The downside of hydrogen is its density; in gaseous form the tanks are impractical for flight, but even in the form of liquid hydrogen it has a density one fourteenth that of water. It is also deeply cryogenic and requires very significant insulation that precludes it being stored in wings. The overall vehicle would end up being very large, and difficult for most airports to accommodate. Finally, pure hydrogen is not found in nature, and must be manufactured either via steam reforming or expensive electrolysis. A few experimental hydrogen-powered aircraft have flown with propellers, and jets have been proposed that may be feasible.

Precooled jet engines

An idea originated by Robert P. Carmichael in 1955 is that hydrogen-fueled engines could theoretically have much higher performance than hydrocarbon-fueled engines if a heat exchanger were used to cool the incoming air. The low temperature allows lighter materials to be used, a higher mass-flow through the engines, and permits combustors to inject more fuel without overheating the engine.
This idea leads to plausible designs like Reaction Engines SABRE, that might permit single-stage-to-orbit launch vehicles, and ATREX, which could permit jet engines to be used up to hypersonic speeds and high altitudes for boosters for launch vehicles. The idea is also being researched by the EU for a concept to achieve non-stop antipodal supersonic passenger travel at Mach 5.

Turborocket

The air turborocket is a form of combined-cycle jet engine. The basic layout includes a gas generator, which produces high pressure gas, that drives a turbine/compressor assembly which compresses atmospheric air into a combustion chamber. This mixture is then combusted before leaving the device through a nozzle and creating thrust.
There are many different types of air turborockets. The various types generally differ in how the gas generator section of the engine functions.
Air turborockets are often referred to as turboramjets, turboramjet rockets, turborocket expanders, and many others. As there is no consensus on which names apply to which specific concepts, various sources may use the same name for two different concepts.

Terminology

To specify the RPM, or rotor speeds, of a jet engine, abbreviations are commonly used:
In many cases, instead of expressing rotor speeds as RPM on cockpit displays, pilots are provided with the speeds expressed as a percentage of the design point speed. For example, at full power, the N1 might be 101.5% or 100%. This user interface decision has been made as a human factors consideration, since pilots are more likely to notice a problem with a two- or 3-digit percentage than with a 5-digit RPM.