Airspeed indicator


The airspeed indicator or airspeed gauge is a flight instrument indicating the airspeed of an aircraft in kilometers per hour, knots, miles per hour and/or meters per second. The recommendation by ICAO is to use km/h, however knots is currently the most used unit. The ASI measures the pressure differential between static pressure from the static port, and total pressure from the pitot tube. This difference in pressure is registered with the ASI pointer on the face of the instrument.

Usage

The ASI has standard color-coded markings to indicate safe operation within the limitations of the aircraft. At a glance, the pilot can determine a recommended speed or if speed adjustments are needed. Single and multi-engine aircraft have common markings. For instance, the green arc indicates the normal operating range of the aircraft, from VS1 to VNO. The white arc indicates the flap operating range, VSO to VFE, used for approaches and landings. The yellow arc cautions that flight should be conducted in this range only in smooth air, while the red line at the top of the yellow arc indicates damage or structural failure may result at higher speeds.
The ASI in multi-engine aircraft includes two additional radial markings, one red and one blue, associated with potential engine failure. The radial red line near the bottom of green arc indicates Vmc, the minimum indicated airspeed at which the aircraft can be controlled with the critical engine inoperative. The radial blue line indicates VYSE, the speed for best rate of climb with the critical engine inoperative.

Operation

The ASI is the only flight instrument that uses both the static system and the pitot system. Static pressure enters the ASI case, while total pressure flexes the diaphragm, which is connected to the ASI pointer via mechanical linkage. The pressures are equal when the aircraft is stationary on the ground, and hence shows a reading of zero. When the aircraft is moving forward, air entering the pitot tube is at a greater pressure than the static line, which flexes the diaphragm, moving the pointer. The ASI is checked before takeoff for a zero reading, and during takeoff that it is increasing appropriately.
The pitot tube may become blocked, because of insects, dirt or failure to remove the pitot cover. A blockage will prevent ram air from entering the system. If the pitot opening is blocked, but the drain hole is open, the system pressure will drop to ambient pressure, and the ASI pointer will drop to a zero reading. If both the opening and drain holes are blocked, the ASI will not indicate any change in airspeed. However, the ASI pointer will show altitude changes, as the associated static pressure changes. If both the pitot tube and the static system are blocked, the ASI pointer will read zero. If the static ports are blocked but the pitot tube remains open, the ASI will operate, but
inaccurately.

Types of airspeeds

Indicated airspeed, is read directly off the ASI. It has no correction for air density variations, installation or instrument errors. Calibrated airspeed is corrected for installation and instrument errors. An airspeed calibration chart is available for any remaining errors. True airspeed is CAS corrected for altitude and nonstandard temperature. TAS is used for flight planning. TAS increases as altitude increases, as air density decreases. TAS may be determined via a flight computer, such as the E6B. Some ASIs have a TAS ring. Alternatively, a rule of thumb is to add 2 percent to the CAS for every of altitude gained.

Jet aircraft

do not have VNO and VNE like piston-engined aircraft, but instead have a maximum operating speed expressed in knots, VMO and Mach number, MMO. Thus, a pilot of a jet airplane needs both an airspeed indicator and a Machmeter, with appropriate red lines. An ASI will include a red-and-white striped pointer, or "barber's pole", that automatically moves to indicate the applicable speed limit at any given time.

Angle of attack and Lift Reserve Indicators

An airplane can stall at any speed, so monitoring the ASI alone will not prevent a stall. The critical angle of attack determines when an aircraft will stall. For a particular configuration, it is a constant independent of weight, bank angle, temperature, density altitude, and the center of gravity of an aircraft. An AOA indicator provides stall situational awareness as a means for monitoring the onset of the critical AOA. The AOA indicator will show the current AOA and its proximity to the critical AOA.
Similarly, the Lift Reserve Indicator provides a measure of the amount of lift being generated. It uses a pressure differential system to provide the pilot with a visual representation of reserve lift available.

Additional reading

Installing and flying the Lift Reserve Indicator, article and photos by Sam Buchanan http://home.hiwaay.net/~sbuc/journal/liftreserve.htm