Ancillary services are the services necessary to support the transmission of electric power from generators to consumers given the obligations of control areas and transmitting utilities within those control areas to maintain reliable operations of the interconnected transmission system. Ancillary services are the specialty services and functions provided by the electric grid that facilitate and support the continuous flow of electricity so that supply will continually meet demand. The term ancillary services is used to refer to a variety of operations beyond generation and transmission that are required to maintain grid stability and security. These services generally include, frequency control, spinning reserves and operating reserves. Traditionally ancillary services have been provided by generators, however, the integration of intermittent generation and the development of smart grid technologies have prompted a shift in the equipment that can be used to provide ancillary services.
Scheduling and dispatch are necessary because in most electrical systems energy storage is nearly zero, so at any instant, the power into the system must equal the power out of the system. Since production must so closely match demand, careful scheduling and dispatch are necessary. Usually performed by the independent system operator or transmission system operator, both are services dedicated to the commitment and coordination of the generation and transmission units in order to maintain the reliability of the power grid. Scheduling refers to before-the-fact actions, while dispatch refers to the real-time control of the available resources.
Consumer loads expect voltage within a certain range, and the regulators require it be within a certain percent of the nominal voltage. Reactive power can be used to compensate the voltage drops, but must be provided closer to the loads than real power needs. Notice that voltage can be controlled also using transformer taps and voltage regulators.
Frequency control
Frequency control refers to the need to ensure that the grid frequency stays within a specific range of the nominal frequency. Mismatch between electricity generation and demand causes variations in frequency, so control services are required to bring the frequency back to its nominal value and ensure it does not vary out of range. If we have a graph for a generator where frequency is on the vertical axis and power is on the horizontal axis: where Pm is the change in power of the system. If we have multiple generators, each might have its own R. Beta can be found by: The change in frequency due to a change in power can be found with: This simple equation can be rearranged to find the change in power that corresponds to a given change in frequency.
Operating reserves
Since production and demand must match so perfectly, operating reserves help make up the difference when production is too low. An operating reserve is a generator that can quickly be dispatched to ensure that there is sufficient energy generation to meet load. Spinning reserves are generators that are already online and can rapidly increase their power output to meet fast changes in demand. Spinning reserves are required because demand can vary on short timescales and rapid response is needed. Other operating reserves are generators that can be dispatched by the operator to meet demand, but that cannot respond as quickly as spinning reserves.
Renewable generation
The grid integration of renewable generation simultaneously requires additional ancillary services and has the potential to provide ancillary services to the grid. The inverters that are installed with distributed generation systems and roof top solar systems have the potential to provide many of the ancillary services that are traditionally provided by spinning generators and voltage regulators. These services include reactive power compensation, voltage regulation, flicker control, active power filtering and harmonic cancellation. Wind turbines with variable-speed generators have the potential to add synthetic inertia to the grid and assist in frequency control. CAISO tested the 131 MW Tule wind farm's synchronverter in 2018, and found it could perform some of the grid services similar or better than traditional generators. Hydro-Québec began requiring synthetic inertia in 2005 as the first grid operator, demanding a temporary 6% power boost when countering frequency drop by combining the power electronics with the rotational inertia of a wind turbine rotor. Similar requirements came into effect in Europe in 2016.
Electric vehicles
s have the potential to be utilized to provide ancillary services to the grid, specifically load regulation and spinning reserves. Plug-in electric vehicles can behave like distributed energy storage and have the potential to discharge power back to the grid through bidirectional flow, referred to as vehicle-to-grid. Plug-in electric vehicles have the ability to supply power at a fast rate which enables them to be used like spinning reserves and provide grid stability with the increased use of intermittent generation such as wind and solar. The technologies to utilize electric vehicles to provide ancillary services are not yet widely implemented, but there is much anticipation of their potential.
