BMC B-series engine


The BMC B series was a line of straight-4 internal combustion engine mostly used in motor cars, created by British company Austin Motor Company.

Design

The precursor of the "B" series engine was a 1200 cc Overhead Valve engine which was used in the 1947-1952 Austin A40 Devon, and, in slightly modified form, in the 1953 Austin A40 Somerset. This engine had the same basic dimensions as one of Austin's pre-war sidevalve engines but to an all-new OHV design which had many features copied from the Chevrolet 235 straight-six engine used on military trucks that the Austin works had overhauled during the Second World War. These features included the valve gear and especially the siamesed cylinder head ports. Austin realised that eventually they would need an engine that could power many of its forthcoming medium-sized cars, and this would require an engine of at least 1500 cc capacity. Since the A40 Devon engine could not have its capacity enlarged, a new engine needed to be designed and built.
The design of this new engine commenced around January 1952, and was designated as the "B" series. The first production version of the B series retained the same 1200cc capacity as the A40 engine and, superficially, appeared to be identical, with the same valve gear, same cylinder head design, same positioning of its ancillary parts and so on. But the B-series block and head were slightly larger in both length and width and the block had thicker cylinder wall castings. This was to allow room for enlargement of the cylinder bore to provide the larger capacities foreseen by BMC. The stroke was retained at and was never altered. Originally of approximately 1.2 Litre capacity, later displacements ranged widely from 1.2 L to 2.4 L, the latter being an Australia only production six-cylinder variant. The most common engine sizes were 1.5 L and 1.8 L and saw service in a number of vehicles. This included a version of the engine built under license in India by Hindustan Motors for its Ambassador series of cars. Petrol versions were produced in the greatest numbers, but diesel versions exist for both cars and marine applications.

Construction

The engine was of conventional construction with a one-piece crankcase and cylinder block in cast iron with the crankcase extending down to the lowest level of the main bearing caps; with a cylinder head, also usually in cast iron, and a sump made from pressed steel for rear-wheel drive vehicles. Early engines used a three-bearing crankshaft, but later engines used five bearings. On all except the rare twin overhead camshaft variant, the camshaft — which was chain driven and mounted low in the block — operated the overhead valves via pushrods and rocker arms. The two inlet ports in the non-crossflow cylinder head were shared between cylinders 1 + 2 and 3 + 4 and the three exhaust ports between cylinder 1, 2 + 3 and 4. Valve clearance was adjustable by screws and locknuts on the rocker arms. Another unconventional characteristic of the engine is that the bore spacing is not constant between all four bores. The distance from cylinder 1 to 2 is 3.4375"; 2 to 3 =3.875" ;and 3 to 4 =3.4375".
The B series shares many design features, as well as its basic layout and general appearance, with the smaller BMC A-series engine. However another difference was its block's full-depth skirt which provided excellent bottom-end strength. This made the engine highly durable and suitable for developing into diesel versions in later years.

Engine types

 litre engines

The version was the first version of the engine. The bore and the stroke was. The maximum power output was at 4300 rpm.
After the formation of British Motor Corporation the new B Series engine was used in the following vehicles:
The version was first used in 1953 in the MG Magnette ZA in twin carburettor version and in 1954 in the Morris Oxford series II and Austin Cambridge. In 1957, it was used in the original MGA. Output in twin carburettor form was and with a single carburettor. Bore and stroke was.
There was also a diesel version of this engine size. Power output was at 4,000 rpm and torque at 1,900 rpm. The 1.5-litre diesel engines were made in India by Hindustan Motors for many decades until the production of the legendary Ambassador was phased out in 2013. They are very popular amongst the taxicab market in India even today.
A special Twin-Cam version of the B-series engine was produced for the MGA. Output was at 6700 rpm in the high-compression version and in the optional low-compression version. The engine block was cast iron, but the crossflow eight-port cylinder head was of aluminium alloy. Drive to the twin camshafts was by chain from a gear-driven, half-speed shaft running in the space that would have been occupied by the conventional camshaft.
This engine gained a reputation for being unreliable in service, especially in the high-compression version which needed high-octane fuel, but this has now been largely overcome. The piston burning habits — thought to be the result of ignition timing — was later discovered to be due to a vibration induced lean burn situation involving the float bowls, easily correctable by flexibly mounting the carburettors. A total of 2,111 cars were built, in both coupé and roadster versions.
A very few engines with the special displacement of were produced for racing purposes.
Applications:
The engine was enlarged to in 1958 by increasing the bore to.
Applications:
The engine was enlarged to in 1961 with another bore increase, this time to.
The B series also formed the basis of the "Blue Streak" engine developed by BMC Australia for use in the locally-built Austin Freeway and Wolseley 24/80 models, both in turn variants of the existing Austin A60 Cambridge. The "Blue Streak" was an inline-6 development of the B series, adding two extra cylinders to create a engine. Different market demands in Australia required the fitting of a six-cylinder engine to a car the size of BMC's mid-range Farina model and the corporate C-series engine would not fit, requiring the development of the unique "Blue Streak" engine. Both models were withdrawn in 1965 and no further use of the engine was made.

 litre engines

The engine was enlarged again to in 1962. Bore was and stroke was still, power varied by application with typically @ 5500 rpm in twin carburettor format and in single carburettor format as used in the Morris Marina. The engine at first had a three-bearing crankshaft with a five-bearing version appearing in 1964.
There was also a diesel version of this capacity, used in the Leyland Sherpa van with a power output of @ 4,250 rpm, and built under license in Turkey for many years. It is still widely used on narrowboats on the canals of the UK.
There was a six-cylinder unit, named "Blue Streak", which was used in the Australian Austin Freeway and Wolseley 24/80.

Engine numbering

There were two series of engine numbers used; BMC changed the system at the end of 1956.

Numbering system, 1936 to 1956

As an example numbers were of the style "BP15GB" followed by the engines serial number, where:
As an example numbers were of the style "15GB-U-H" plus a serial number, where:
Beginning in the early 1970s the numbering system was simplified to "18 V" plus a serial number, where 18 represents the capacity and V = vertical, i.e. longitudinal engine with rear-wheel drive, and H = Horizontal, i.e. transverse engine with front-wheel drive.
There was sometimes a country indicator after the first part of the code, e.g. "18V-Z" was use for some United States MG MGB engines.