Blackfin


The Blackfin is a family of 16-/32-bit microprocessors developed, manufactured and marketed by Analog Devices. The processors have built-in, fixed-point digital signal processor functionality supplied by 16-bit multiply–accumulates, accompanied on-chip by a microcontroller. It was designed for a unified low-power processor architecture that can run operating systems while simultaneously handling complex numeric tasks such as real-time H.264 video encoding.

Architecture details

Blackfin processors use a 32-bit RISC microcontroller programming model on a SIMD architecture, which was co-developed by Intel and Analog Devices, as MSA.
The architecture was announced in December 2000, and first demonstrated at the Embedded Systems Conference in June, 2001.
It incorporates aspects of ADI's older SHARC architecture and Intel's XScale architecture into a single core, combining digital signal processing and microcontroller functionality. There are many differences in the core architecture between Blackfin/MSA and XScale/ARM or SHARC, but the combination was designed to improve performance, programmability and power consumption over traditional DSP or RISC architecture designs.
The Blackfin architecture encompasses various CPU models, each targeting particular applications. The BF-7xx series, introduced in 2014, comprise the Blackfin+ architecture, which expands on the Blackfin architecture with some new processor features and instructions.

Architecture features

Core features

What is regarded as the Blackfin "core" is contextually dependent. For some applications, the DSP features are central. Blackfin has two 16-bit hardware MACs, two 40-bit ALUs and accumulators, a 40-bit barrel shifter, and four 8-bit video ALUs; Blackfin+ processors add a 32-bit MAC and 72-bit accumulator. This allows the processor to execute up to three instructions per clock cycle, depending on the level of optimization performed by the compiler or programmer. Two nested zero-overhead loops and four circular buffer DAGs are designed to assist in writing efficient code requiring fewer instructions. Other applications use the RISC features, which include memory protection, different operating modes, single-cycle opcodes, data and instruction caches, and instructions for bit test, byte, word, or integer accesses and a variety of on-chip peripherals.
The ISA is designed for a high level of expressiveness, allowing the assembly programmer to optimize an algorithm for the hardware features present. The standard Blackfin assembly language is written using an algebraic syntax: instead of prefix commands used in many other assembly languages such as ld R0, 8, add R0, R1, R2, and push R7, Blackfin assembly uses R0 = , R0 = R1 + R2, and = R7.

Memory and DMA

The Blackfin uses a byte-addressable, flat memory map. Internal L1 memory, internal L2 memory, external memory and all memory-mapped control registers reside in this 32-bit address space, so that from a programming point of view, the Blackfin has a Von Neumann architecture.
The L1 internal SRAM memory, which runs at the core-clock speed of the device, is based on a Harvard architecture. Instruction memory and data memory are independent and connect to the core via dedicated memory buses, designed for higher sustained data rates between the core and L1 memory.
Portions of instruction and data L1 SRAM can be optionally configured as cache independently.
Certain Blackfin processors also have between 64KB and 256KB of L2 memory. This memory runs slower than the core clock speed. Code and data can be mixed in L2.
Blackfin processors support a variety of external memories including SDRAM, DDR-SDRAM, NOR flash, NAND flash and SRAM. Some Blackfin processors also include mass-storage interfaces such as ATAPI and SD/SDIO. They can support hundreds of megabytes of memory in the external memory space.
Coupled with the core and memory system is a DMA engine that can operate between any of its peripherals and main memory. The processors typically have a dedicated DMA channel for each peripheral, which is designed for higher throughput for applications that can use it, such as real-time standard-definition video encoding and decoding.

Microcontroller features

The architecture of Blackfin contains the usual CPU, memory, and I/O that is found on microprocessors or microcontrollers. These features enable operating systems.
All Blackfin processors contain a Memory Protection Unit. The MPU provides protection and caching strategies across the entire memory space. The MPU allows Blackfin to support operating systems, RTOSs and kernels like ThreadX, μC/OS-II, or NOMMU Linux. Although the MPU is referred to as a Memory Management Unit in the Blackfin documentation, the Blackfin MPU does not provide address translation like a traditional MMU, so it does not support virtual memory or separate memory addresses per process. This is why Blackfin currently can not support operating systems requiring virtual memory such as WinCE or QNX.
Blackfin supports three run-time modes: supervisor, user and emulation. In supervisor mode, all processor resources are accessible from the running process. However, when in user mode, system resources and regions of memory can be protected. In a modern operating system or RTOS, the kernel typically runs in supervisor mode and threads/processes will run in user mode. If a thread crashes or attempts to access a protected resource an exception will be thrown and the kernel will then be able to shut down the offending thread/process. The official guidance from ADI on how to use the Blackfin in non-OS environments is to reserve the lowest-priority interrupt for general-purpose code so that all software is run in supervisor space.
Blackfin uses a variable-length RISC-like instruction set consisting of 16-, 32- and 64-bit instructions. Commonly used control instructions are encoded as 16-bit opcodes while complex DSP and mathematically intensive functions are encoded as 32- and 64-bit opcodes. This variable length opcode encoding is designed for code density equivalence to modern microprocessor architectures.

Media-processing features

The Blackfin instruction set contains media-processing extensions to help accelerate pixel-processing operations commonly used in video compression and image compression and decompression algorithms.

Peripherals

Blackfin processors contain an array of connectivity peripherals, depending on the specific processor:
All of the peripheral control registers are memory-mapped in the normal address space.

Development tools

ADI provides its own software development toolchains. The original VisualDSP++ IDE is still supported, but is approaching end of life and has not had support added for the new BF6xx and BF7xx processors. The newer toolchain is CrossCore Embedded Studio, which uses supports all Blackfin and Blackfin+ processors using upgraded versions of the same compiler and tools internally, but with a UI based on Eclipse CDT. No free version of either tool is available; a single-user license for VisualDSP++ costs $3500 USD, and CrossCore Embedded Studio $995 USD.
Other options include Green Hills Software's MULTI IDE and the GNU GCC Toolchain for the Blackfin processor family. However, like VisualDSP++, these have not been updated to support the newer BF6xx and BF7xx processors. Moreover, neither support all BF5xx processors. Green Hills MULTI lacks support for BF50x, BF51x, some BF52x, BF547, and BF59x. GCC lacks support for BF50x, BF566, and BF59x, and has incomplete support for BF561.
Blackfin is also supported by National Instruments' LabVIEW Embedded Module, which requires VisualDSP++.

Supported operating systems, RTOSs and kernels

Several commercial and open-source operating systems support running on Blackfin.
TitleLicenseComments
ThreadX
Nucleus
μC/OS-II
INTEGRITY
RTEMS
RTXC Quadros
VDKADI's real-time kernel. Ships with VisualDSP++.
.NET Micro FrameworkStand-alone version from Microsoft. Integrated version from AxiomFount.

Blackfin was previously supported by μClinux and later by Linux with the NOMMU feature, but as it was not ever widely used and no longer had a maintainer, support was removed from Linux on April 1, 2018; 4.16 was the last release to include Blackfin support.