Category 5 cable


Category 5 cable is a twisted pair cable for computer networks. Since 2001, the variant commonly in use is the Category 5e specification. The cable standard provides performance of up to 100 MHz and is suitable for most varieties of Ethernet over twisted pair up to . Cat 5 is also used to carry other signals such as telephony and video.
This cable is commonly connected using punch-down blocks and modular connectors. Most Category 5 cables are unshielded, relying on the balanced line twisted pair design and differential signaling for noise rejection.

Standards

The specification for category 5 cable is defined in ISO/IEC 11801, IEC 61156 and EN 50173.
The specification for category 5 cable was defined in ANSI/TIA/EIA-568-A, with clarification in TSB-95. These documents specify performance characteristics and test requirements for frequencies up to 100 MHz.
The cable is available in both stranded and solid conductor forms. The stranded form is more flexible and withstands more bending without breaking. Patch cables are stranded. Permanent wiring used in structured cabling is solid-core. The category and type of cable can be identified by the printing on the jacket.

Variants and comparisons

The category 5e specification improves upon the category 5 specification by revising and introducing new specifications to further mitigate the amount of crosstalk. The bandwidth and physical construction are the same between the two, and most Cat 5 cables actually meet Cat 5e specifications, though they are not specifically certified as such. The category 5 was deprecated in 2001 and superseded by the category 5e specification.
The Category 6 specification improves upon the Category 5e specification by extending frequency response and further reducing crosstalk. The improved performance of Cat 6 provides 250 MHz bandwidth. Category 6A cable provides 500 MHz bandwidth. Both variants are backwards compatible with Category 5 and 5e cables.

Termination


, B for T568B
in T568B wiring

Cable types, connector types and cabling topologies are defined by TIA/EIA-568-B. Nearly always, 8P8C modular connectors are used for connecting category 5 cable. The cable is terminated in either the T568A scheme or the T568B scheme. The two schemes work equally well and may be mixed in an installation so long as the same scheme is used on both ends of each cable.

Applications

Category 5 cable is used in structured cabling for computer networks such as Ethernet over twisted pair. The cable standard provides performance of up to and is suitable for, , ,, and, under some circumstances,. and Ethernet connections require two wire pairs. 1000BASE-T and faster Ethernet connections require four wire pairs. Through the use of power over Ethernet, power can be carried over the cable in addition to Ethernet data.
Cat 5 is also used to carry other signals such as telephony and video. In some cases, multiple signals can be carried on a single cable; Cat 5 can carry two conventional telephone lines as well as 100BASE-TX in a single cable. The USOC/RJ-61 wiring standard may be used in multi-line telephone connections. Various schemes exist for transporting both analog and digital video over the cable. HDBaseT is one such scheme.

Characteristics

The use of balanced lines helps preserve a high signal-to-noise ratio despite interference from both external sources and crosstalk from other pairs.
PropertyNominalToleranceUnitref
, 100± 15
100± 5
DC loop resistance≤ 0.188
Propagation speed0.64c
Propagation delay4.80–5.30
Delay skew < 0.20
Capacitance at 52
Inductance525
Corner frequency≤ 57
Max tensile load, during installation100
Wire diameter24 AWG ;
Insulation thickness0.245mm
Maximum current per conductor0.577
Operating temperature−55 to +60

125

Insulation

Outer insulation is typically polyvinyl chloride or low smoke zero halogen.
AcronymMaterial
PEPolyethylene
FPFoamed polyethylene
FEPFluorinated ethylene propylene
FFEPFoamed fluorinated ethylene propylene
AD/PEAir dielectric/polyethylene
LSZH or LS0HLow smoke, zero halogen
LSFZH or LSF0HLow smoke and fume, zero halogen

Bending radius

Most Category 5 cables can be bent at any radius exceeding approximately four times the outside diameter of the cable.

Maximum cable segment length

The maximum length for a cable segment is per TIA/EIA 568-5-A. If longer runs are required, the use of active hardware such as a repeater or switch is necessary. The specifications for 10BASE-T networking specify a 100-meter length between active devices. This allows for 90 meters of solid-core permanent wiring, two connectors and two stranded patch cables of 5 meters, one at each end.

Conductors

Since 1995, solid-conductor UTP cables for backbone cabling is required to be no thicker than 22 American Wire Gauge and no thinner than 24 AWG, or 26 AWG for shorter-distance cabling. This standard has been retained with the 2009 revision of ANSI TIA/EIA 568.Commercial Building Telecommunications Cabling Standard">
Although cable assemblies containing are common, category 5 is not limited to 4 pairs. Backbone applications involve using up to.

Individual twist lengths

The distance per twist is commonly referred to as pitch. Each of the four pairs in a Cat 5 cable has differing precise pitch to minimize crosstalk between the pairs. The pitch of the twisted pairs is not specified in the standard. Measurements on one sample of Cat 5 cable yielded the following results.
Pair color[cm] per turnTurns per [m]
Blue1.3872
Green1.5365
Orange1.7856
Brown1.9452

Since the pitch of the various colors is not specified in the standard, pitch can vary according to manufacturer and should be measured for the batch being used if cable is being used in non-Ethernet situation where pitch might be critical.

Environmental ratings

ClassPhraseDescriptionStandards
LSZHCommunications low-smoke zero halogenNES‑711, NES‑713, MIL‑C‑24643, UL 1685
CMPCommunications plenumInsulated with fluorinated ethylene propylene and polyethylene and jacketed with low-smoke polyvinyl chloride, due to better flame test ratings.CSA FT6 or NFPA 262
CMRCommunications riserInsulated with high-density polyolefin and jacketed with low-smoke polyvinyl chloride.
UL 1666
CMGCommunications general purposeCSA FT4
CMCommunicationsInsulated with high-density polyolefin, but not jacketed with PVC and therefore is the lowest of the three in flame resistance.UL 1685 Vertical-Tray
CMXCommunications residentialInsulation with polyolefin and jacketed with polyethylene.UL 1581, Sec. 1080
CMHCSA FT1

Some cables are "UV-rated" or "UV-stable" meaning they can be exposed to outdoor UV radiation without significant degradation.
Plenum-rated cables are slower to burn and produce less smoke than cables using a mantle of materials like PVC. Plenum-rated cables may be installed in plenum spaces where PVC is not allowed.
Shielded cables are useful for environments where proximity to RF equipment may introduce electromagnetic interference, and can also be used where eavesdropping likelihood should be minimized.