Electrostatic loudspeaker
An electrostatic loudspeaker is a loudspeaker design in which sound is generated by the force exerted on a membrane suspended in an electrostatic field.
Design and functionality
The speakers use a thin flat diaphragm usually consisting of a plastic sheet coated with a conductive material such as graphite sandwiched between two electrically conductive grids, with a small air gap between the diaphragm and grids. For low distortion operation, the diaphragm must operate with a constant charge on its surface, rather than with a constant voltage. This is accomplished by either or both of two techniques: the diaphragm's conductive coating is chosen and applied in a manner to give it a very high surface resistivity, and/or a large value resistor is placed in series between the EHT power supply and the diaphragm. However, the latter technique will still allow distortion as the charge will migrate across the diaphragm to the point closest to the "grid" or electrode thereby increasing the force moving the diaphragm, this will occur at audio frequency so the diaphragm requires a high resistance to slow the movement of charge for a practical speaker.The diaphragm is usually made from a polyester film with exceptional mechanical properties, such as PET film. By means of the conductive coating and an external high voltage supply the diaphragm is held at a DC potential of several kilovolts with respect to the grids. The grids are driven by the audio signal; front and rear grid are driven in antiphase. As a result, a uniform electrostatic field proportional to the audio signal is produced between both grids. This causes a force to be exerted on the charged diaphragm, and its resulting movement drives the air on either side of it.
In virtually all electrostatic loudspeakers the diaphragm is driven by two grids, one on either side, because the force exerted on the diaphragm by a single grid will be unacceptably non-linear, thus causing harmonic distortion. Using grids on both sides cancels out voltage dependent part of non-linearity but leaves charge dependent part. The result is near complete absence of harmonic distortion. In one recent design, the diaphragm is driven with the audio signal, with the static charge located on the grids.
The grids must be able to generate as uniform an electric field as possible, while still allowing for sound to pass through. Suitable grid constructions are therefore perforated metal sheets, a frame with tensioned wire, wire rods, etc.
To generate a sufficient field strength, the audio signal on the grids must be of high voltage. The electrostatic construction is in effect a capacitor, and current is only needed to charge the capacitance created by the diaphragm and the stator plates. This type of speaker is therefore a high-impedance device. In contrast, a modern electrodynamic cone loudspeaker is a low impedance device, with higher current requirements. As a result, impedance matching is necessary in order to use a normal amplifier. Most often a transformer is used to this end. Construction of this transformer is critical as it must provide a constant transformation ratio over the entire audible frequency range and so avoid distortion. The transformer is almost always specific to a particular electrostatic speaker. To date, Acoustat built the only commercial "transformer-less" electrostatic loudspeaker. In this design, the audio signal is applied directly to the stators from a built-in high-voltage valve amplifier, without use of a step-up transformer.
Advantages
Advantages of electrostatic loudspeakers include:- levels of distortion one to two orders of magnitude lower than conventional cone drivers in a box
- the extremely light weight of the diaphragm which is driven across its whole surface
- exemplary frequency response because the principle of generating force and pressure is almost free from resonances unlike the more common electrodynamic driver.
Since many electrostatic speakers are tall and thin designs without an enclosure, they act as a vertical dipole line source. This makes for rather different acoustic behavior in rooms compared to conventional electrodynamic loudspeakers. Generally speaking, a large-panel dipole radiator is more demanding of a proper physical placement within a room when compared to a conventional box speaker, but, once there, it is less likely to excite bad-sounding room resonances, and its direct-to-reflected sound ratio is higher by some 4–5 decibels. This in turn leads to more accurate stereo reproduction of recordings that contain proper stereo information and venue ambience. Planar drivers tend to be very directional giving them good imaging qualities, on the condition that they have been carefully placed relative to the listener and the sound-reflecting surfaces in the room. Curved panels have been built, making the placement requirements a bit less stringent, but sacrificing imaging precision somewhat.
Disadvantages
Typical disadvantages include sensitivity to ambient humidity levels and a lack of bass response, due to phase cancellation from a lack of enclosure, but these are not shared by all designs. The bass rolloff 3db point occurs when the narrowest panel dimension equals a quarter wavelength of the radiated frequency for dipole radiators, so for a Quad ESL-63, which is 0.66 meters wide, this occurs at around 129 Hz, comparable to many box speakers. There is also the difficult physical challenge of reproducing low frequencies with a vibrating taut film with little excursion amplitude; however, as most diaphragms have a very large surface area compared to cone drivers, only small amplitude excursions are required to put relatively large amounts of energy out. While bass is lacking quantitatively it can be of better quality than that of electrodynamic systems. Phase cancellation can be somewhat compensated for by electronic equalization. Nevertheless maximum bass levels cannot be augmented because they are ultimately limited by the membrane's maximum permissible excursion before it comes too close to the high-voltage stators, which may produce electrical arcing and burn holes through it. Recent, technically more advanced solutions for perceived lack of bass include the use of large, curved panels, electrostatic subwoofer panels, and long-throw electrostatic elements allowing large diaphragm excursions. Another trick often practiced is to step up the bass with a higher transformation ratio than the mid and treble.This relative lack of loud bass is often remedied with a hybrid design using a dynamic loudspeaker, e.g. a subwoofer, to handle lower frequencies, with the electrostatic diaphragm handling middle and high frequencies. Many feel that the best low frequency unit for hybrids are cone drivers mounted on open baffles as dipoles, transmission line woofers or horns, since they possess roughly the same qualities as electrostatic speakers, i.e. good transient response, little box coloration, and flat frequency response. However, there is often a problem with integrating such a woofer with the electrostatics. This is because most electrostatics are line sources, the sound pressure level of which decreases by 3 dB for each doubling of distance. A cone speaker's sound pressure level, on the other hand, decreases by 6 dB for each doubling of distance because it behaves as a point source. This can be overcome by the theoretically more elegant solution of using conventional cone woofer in an open baffle, or a push-pull arrangement, which produces a bipolar radiation pattern similar to that of the electrostatic membrane. This is still subject to phase cancellation, but cone woofers can be driven to far higher levels due to their longer excursion, thus making equalization to a flat response easier, and they add distortion thereby increasing the area under the frequency response graph, making the total low frequency energy higher but the fidelity to the signal lower.
An alternative is to enclose the electrostatic elements and operate them as "monopoles." This avoids the many disadvantages of dipole operation, most importantly a great reduction in room reflections and thus also in adulteration of the recorded ambiance. Since there's no attempt at making the speaker visually see-through, it also allows the application of materials to the rear of the panel to impart full damping of the membrane resonance, which improves transient response. In addition, using relatively small elements with a relatively high crossover frequency, such as 500 Hz, has a number of advantages. It reduces directivity to a degree that offers a reasonably wide sweet spot. It allows more of the 3 dB/octave increase in SPL with frequency to be used, increasing the sensitivity. It does not act as a true line array, so woofers are easier to integrate. Lastly, most of the remaining 3 dB roll-up can be counteracted by filtering the high frequencies from the signal to half or more of the width, which coincidentally widens the dispersion and thus the sweet spot. JansZen speakers incorporate all these alternative features. They also use acoustic suspension woofers, which have the lowest group delay of all configurations and thus the best chance of seamlessly integrating with the electrostatics. The panels are also well protected from collecting airborne contaminants, avoiding the need for periodic repairs.
The directionality of electrostatics can also be a disadvantage in that it means the 'sweet spot' where proper stereo imaging can be heard is relatively small, limiting the number of people who can fully enjoy the advantages of the speakers simultaneously. In 1992 Critical Mass introduced the first electrostatic speakers for use in the mobile environment. Critical Mass engineer and CEO Wayde Alfarone's design capitalized on the directional nature of electrostats by creating separate sound fields for different seating locations in the vehicle.
Because of their tendency to attract dust, insects, conductive particles, and moisture, electrostatic speaker diaphragms will gradually deteriorate and need periodic replacement. They also need protection measures to physically isolate their high voltage parts from accidental contact with humans and pets. Cost-effective repair and restoration service is available for virtually every current and discontinued electrostatic loudspeaker model.
Amateur-built speakers
Electrostatic speakers enjoy some popularity among do-it-yourself loudspeaker builders. They are one of the few types of speakers in which the transducers themselves can be built from scratch by an amateur as basic hardware for complete ESL DIY projects can be found available online. Such supplies include resistors and capacitors for RC circuit frequency equalization, if necessary; step-up transformers; perforated metal sheets or grids and insulating plastics for the stators; polymer film and conductive paint for the membrane; simple tensioning equipment for proper membrane tuning; and a frame, usually of wood, to hold everything together. A widely read resource by ESL enthusiasts is The Electrostatic Loudspeaker Design Cookbook by notable ESL specialist Roger Sanders.Commercial speakers
Arthur Janszen was granted in 1953 for an electrostatic loudspeaker. He had worked in the Navy to develop a low-distortion, high-frequency source for targeting torpedoes. After the war, he developed manufacturing technique for electrostatic speakers, to be used with conventional cone woofers, known as electrostatic hybrids. He licensed Neishammny Electric to make these speakers. In the early 1970s, Electronic Industries of Minneapolis took over the license and rights to make JansZen electrostatic speakers. In 1974, Electronic Industries introduced a new wire wrap around ESL tweeter that great lowered the cost to manufacture. It also has proven to be totally reliable. Several large arrays of these tweeters were actually used as public address systems in concerts in Minneapolis. Ownership changed again in the late 1970s, and the company was bought. Plans were made to offer electrostatic speakers in cars, but never came into production. Dave Wilson of Wilson audio, used JansZen tweeters in his famous, WAMM, Wilson Audio MOdulator Monitor. That speaker sold for $220,000 pair when it was discontinued. The developers of the Tri-Ergon sound-on-film sound film system had developed a primitive design of electrostatic loudspeaker as early as 1919. David JansZen, son of Arthur JansZen, using his father's papers and designs introduced his own version of electrostatic hybrid speakers. His company, still in business, was not connected to Electronic Industries JansZen speakers. Mr. Janszen's company, JansZen still makes an evolved version of his original design. The KLH Nine was designed in the mid-1950s by Arthur A. Janszen, and thousands were sold after the design was brought over to KLH in 1959 and put into regular production.Quad Electroacoustics
The first fully successful full-range electrostatic speaker, and also among the most influential, was produced in 1957: the Quad Electrostatic Loudspeaker from Quad Electroacoustics, of Huntingdon, England. These were shaped somewhat like a home electric radiator curved slightly on the vertical axis. They were widely admired for their clarity and precision, but can be difficult to run while achieving low frequency bass output.The Quad ESLs were designed by Peter Walker, founder of the company, and David Williamson. The first in the series was the ESL-57, influenced by developed by Edward W. Kellogg for General Electric in 1934. It was introduced in 1955, put into commercial production in 1957, and discontinued only in 1985.
In 1981, Quad introduced the ESL-63 as a successor to the ESL-57. It attempted to address both the deficiency in bass reproduction of the ESL-57 and its extreme directionality at high frequencies. The latter goal is achieved by splitting the stators into eight concentric rings, each fed with a slight time delay compared to the ring immediately inwards, thereby attempting to emulate a point source.
Although the ESL-63 was discontinued in 1999, Quad maintains production of electrostatic speakers. Quad introduced the ESL-988 and its larger variant the ESL-989 in 1999, the ESL-2805 and ESL-2905 in 2005, and the ESL-2812 and ESL-2912 in 2017, that incorporate electronic and transducer refinements.
Other manufacturers
Other manufacturers currently producing electrostatic loudspeakers include Immersion from Australia;, Solosound in The Netherlands, King's Audio, Panphonics from Finland, Pune based Cadence Audio, T+A and Silberstatic from Germany. In late 2014, Taiwanese technology manufacturer BenQ released world's first portable electrostatic Bluetooth speaker treVolo.Audiostatic, Blanko.nu exclusively tubeamp active electrostatic loudspeakers handbuild in Holland, Sound-Lab exclusively build full-range electrostatic panels. The only active, full range electrostatic loudspeaker currently in production is the Audiostatic DCA-5. currently offers active versions of its two hybrid models, the Carmelita Active and the Valentina Active.
MartinLogan, , Metrum Acoustics, Sanders Sound Systems, and Sound-Lab, build hybrid designs with conventional woofers or subwoofers.
Among electrostatic full-range speakers that are no longer made is the KLH 9, the earliest US full-range design. Under ideal, in-room conditions, the bass is well supported down to 40 Hz @ -3 dB but starts rolling off as high as 80 Hz if the woofer membranes were excessively tensioned in production or due to age. There were several Acoustat models manufactured, and the Infinity Servo-Statik and its successors which used a dynamic woofer/subwoofer at low frequencies. Sanders Sound Systems is the successor to the defunct Innersound.