Glowplug
A glowplug is a heating device used to aid starting diesel engines. In cold weather, high speed diesel engines can be difficult to start because the mass of the cylinder block and cylinder head absorb the heat of compression, preventing ignition. Pre-chambered engines use small glowplugs inside the pre-chambers. Direct-injected engines have these glowplugs in the combustion chamber. The glowplug is a pencil-shaped piece of metal with a heating element at the tip. This heating element, when electrified, heats due to its electrical resistance and begins to emit light in the visible spectrum, hence the term glowplug. The visual effect is similar to the heating element in a toaster. The fuel injector spray pattern then impinges directly upon the hot tip of the glow plug during the injection of fuel at top dead center. This ignites the fuel even when the engine is insufficiently hot for normal operation, which reduces the cranking time to start the engine.
Overview
s, unlike gasoline engines, do not use spark plugs to induce combustion. Instead, they rely solely on compression to raise the temperature of the air to a point where the diesel combusts spontaneously when introduced to the hot, high pressure air. The high pressure and spray pattern of the diesel ensures a controlled, complete burn. The piston rises, compressing the air in the cylinder; this causes the air's temperature to rise. By the time the piston reaches the top of its travel path, the temperature in the cylinder is very high. The fuel mist is then sprayed into the cylinder; it instantly combusts, forcing the piston downwards, thus generating power. The pressure required to heat the air to that temperature, however, requires a large and strong engine block.The temperature at the top of the compression stroke depends on many factors, particularly the compression ratio of the cylinder and the starting temperature of the inducted air. When the engine is cold, the temperature of the inducted air is low and it receives little heat from the engine cylinder walls. In addition, as the air is compressed and becomes heated, some of this heat is lost to the cold cylinder walls, further reducing the temperature at the top of the compression stroke. The glow plug solves this.
There are two different glow plug types: the in-cylinder variety and the in-manifold variety. In the case of in-cylinder, there is a plug in every cylinder direct injected. In the case of the in-manifold one, there is only one for all the cylinders.
In general, diesel engines do not require any starting aid. Therefore, some diesel engines, especially direct injected ones, do not have starting aid systems such as glowplugs. This however depends upon the displacement and combustion chamber design, and engines with a lot of combustion chamber surface, such as precombustion chamber and swirl chamber injected engines, may require the use of glowplugs to start properly. The minimum starting temperature without using glowplugs is 40 °C for precombustion chamber injected, 20 °C for swirl chamber injected, and 0 °C for direct injected engines. Engines with a displacement of more than one litre per cylinder usually incorporate a flame-start system rather than glowplugs, if a starting aid system is required.
Method of operation
Pre-heating
In older generation diesel-engine vehicles, unlike in a gasoline-engine vehicle, for a 'cold start' the operator did not simply turn the key to the "start" position and have the engine immediately start. Instead, the operator activated the glow plug for a time first. Early diesels used the 'Thermostart' type glowplug in the inlet manifold. These take 20 seconds to achieve working temperature and the vehicle operator had to manually time when the 20 seconds had elapsed. With in-cylinder glow plugs, technological improvements included a warning light on the dash to indicate how long the preheating should last. The preheating phase was also made to be automatically activated when the operator turned the key to the "on" position for a long duration; the glowplug relay switches the glowplugs on, and a light on the instrument cluster illuminates. This process is called "pre-heating" or "glowing". Many modern diesels automatically activate their glow plugs when the operator unlocks the vehicle or opens the door to the car, thus simplifying the process and shortening the time the operator has to wait before the engine will start. According to Bosch: "Older engines with Thermostart manifold plugs used a glow period of up to 20 seconds whereas more modern engines use around a 6 to 8 second heat period and provide after glow at a reduced voltage."Starting
Before any attempt is made to start a vehicle engine, the vehicle's parking brake should be firmly applied and gear selection should be in Neutral. Any engine stop control should be returned to the run position and in cold weather, any 'excess fuel' starting aid should be set or used - such as Ki-Gass.With in-cylinder glow plugs, when a pre-set time has elapsed, the glowplug relay switches off the "wait-to-start" light. A pre-heating cycle usually lasts for 2 to 5 seconds. The operator then proceeds to turn the key to the "start" position. The relay switches off the glowplugs after the engine is running. In some cars, in order to maintain compliance with emissions regulations, the glow plugs may be operated immediately after engine start, or during periods of extended idle where engine temperature has decreased, as combustion efficiency is greatly reduced when the engine is below operating temperature.
With a Thermostart plug in the inlet manifold, within a few seconds diesel vapours start to fill the inlet manifold. As the plug continues to heat up, it opens a valve permitting diesel from a special reservoir mounted directly above the Thermostart into the Thermostart plug. This fresh diesel is also vaporised and adds to that in the inlet manifold. At 20 seconds, provided air is available, the diesel near the plug ignites and as the engine is cranked, the ignited diesel is drawn into the combustion chambers - to which more diesel is added after the compression stroke. This additional diesel immediately ignites, starting the engine with ease. Vehicles fitted with Thermostart glow plugs do not usually activate via the normal ignition switch. A button elsewhere is provided. Where a Thermostart is activated by the same switch as the ignition, it is usually activated by turning the switch one 'notch' counter-clockwise. After the 20 second period has elapsed, cranking is achieved by turning the ignition switch a further notch counter-clockwise. Once the engine has fired and is running, the ignition switch is released, allowing it to spring back to the off position. The operator should then turn the ignition switch to the on position - usually one notch clockwise
Warm engine start
If the car had been running very recently, or if the ambient temperature was hot, the "wait to start" light might not come on. In this case, the operator may proceed to turn the key to the "start" position and start the engine without having to wait.With a Thermostart, it is entirely up to the operator to choose whether to activate the glow plug. In the case of ignition key controlled Thermostart, turning the key two notches to the right initiates unheated cranking.
Construction
A glowplug resembles a short metal pencil. The heating filament is fitted into its tip. Glowplug filaments must be made of certain materials, such as platinum and iridium, that resist oxidation and high temperature.Model engines
Glow plugs in model engines differ from those in full-size diesel engines. Full-size engines only use the glow plug for starting. Model engines use a glow plug as an integral part of the ignition system because of the catalytic effect of the platinum wire, on the methanol-base fuel they are designed to run on.Model engine glow plugs are also used as re-usable igniters in theatrical pyrotechnics and the special effects industry to remotely ignite pyrotechnic devices using flash and smoke composition powders.