Krauss-Maffei ML 4000
The Krauss-Maffei ML 4000 C′C′ is a road switcher diesel-hydraulic locomotive, built between 1961 and 1969 by German manufacturer Krauss-Maffei in Munich, Germany. It generated from two Maybach V16 engines. 37 examples were built for two North American railroads and one South American railroad.
History
In 1959, General Motors’ Electro-Motive Division rebuilt nine of its GP9 locomotives for the Union Pacific Railroad with pre-production examples of a new turbo-supercharging system that would raise the locomotives’ horsepower to 2000. This soon evolved into the GP20.The Southern Pacific Railroad took this into account, as business for SP was growing rapidly. Freight trains were getting longer and heavier, and SP had to use up to nearly 10 locomotives to power long-distance freight trains. SP's main workhorses at the time were EMD F7s and GP9s. Although SP had a small fleet of H-24-66 "Train Master" locomotives manufactured by Fairbanks-Morse, SP found that they were not suitable for freight service and were relegated to the San Francisco Bay Area's Peninsula Commutes.
After much research, SP decided to experiment with diesel-hydraulic locomotives and stunned the railroading industry by purchasing three ML-4000 type locomotives from German manufacturer Krauss-Maffei. Delivered by ship and unloaded at the Port of Houston, Texas, on October 31, 1961, they featured two Maybach V16 diesel engines and Voith transmissions. The Denver and Rio Grande Western Railroad also ordered three units, but found them unsuitable in mountain service, and they were sold to the SP in early 1964. Upon arrival, a special track was set up at the locomotive shops in Roseville, California, just for servicing the ML-4000s.
The first order of the ML-4000s are referred to as “cab units,” given that they have a fully enclosed car body, similar to that of the EMD F-unit. Following extensive testing SP returned to Krauss-Maffei for an additional fifteen units. Delivered in 1964, they featured the same engines and transmissions but looked very different on the outside. These are referred to as “hood units” because of their hood type bodies.
SP found the ML-4000s unsatisfactory in service over the Sierra Nevada mountain range, so they were relegated to service in flat territory throughout California, often paired with F7s or GP9s. The locomotives were fairly reliable, with only one recorded failure. Upon ordering the second batch of ML-4000s, SP also purchased three DH643 diesel-hydraulic locomotives from Alco.
Disposition
American locomotive technology began to catch up in the late 1960s, and the operation of diesel-hydraulic locomotives, while useful, was no longer justifiable. SP and other railroads had made their horsepower needs known and American builders responded by increasing horsepower on single-engine locomotives. In 1966, SP first ordered the EMD SD40 and SD45 locomotives from EMD. These new EMD locomotives, along with the U30C and U33Cs from General Electric, quickly became the new high horsepower units of choice. In 1967, a deadline of ML-4000 cab units appeared at the Sacramento Locomotive Works. Hood units soon appeared in the deadline, and the first ML-4000s were retired in September of that year. The Pacific Locomotive Association came to SP with a request of a diesel-hydraulic powered railfan passenger excursion, preferably with a ML-4000 cab unit. However, the cab units were no longer operational, so hood unit number 9120, along with a pair of EMD FP7s powered a series of railfan passenger excursions in the spring of 1967, the only time an ML-4000 was used in passenger service. On February 13, 1968, SP announced the end of its diesel-hydraulic locomotive program. By the end of the year, all ML-4000s had been retired. The trio of ALCO diesel-hydraulics fared slightly better, and were not retired until 1973. The powered trucks were salvaged from some of the scrapped ML 4000's and sold to Plasser & Theurer, where they were installed on that company's self-propelled ballast cleaners.The camera car
Before the end of 1968, all but one of the ML 4000s were scrapped at Sacramento. The survivor, number 9113 was converted into a "camera car" between 1968 and 1969 at the Sacramento Locomotive Works. It emerged as SPMW #1, but was later renumbered SPMW 1166 due to SP's traffic computer requiring 4 digits. In June 1969, it was finally renumbered to SP 8799. Its purpose was to record films for a computerized locomotive simulator for engineer training. The most drastic change in appearance was the locomotive's short hood. It was completely rebuilt to house camera equipment and heavy, thick steel was used for collision protection. The front transmission was removed to house a generator to power the camera equipment. The generator drew fuel from the locomotive's original fuel tank. The two engines and rear transmission, though disabled, remained in the engine for weight. All of the controls remained in the cab so that it could control a locomotive pushing behind it, much like a cab car is used on a commuter train. The camera car could be put on the lead of any train, but it mostly made special trips with just one locomotive behind it for power. SP 8799 was based out of SP's West Colton Yard in Southern California until it was retired in 1984.The Brazilian ML-4000s
of Brazil ordered four units built to meter gauge in 1966. An additional 12 units were built in 1969. They were the most powerful locomotives for use in meter gauge at that time. Although they had problems with traction, they stayed in service until the 1980s with the arrival of the EMD DDM45. All of them were scrapped.Original buyers
Preservation
SP camera car 8799 was donated to the California State Railroad Museum in Sacramento in 1986. Initially, the museum removed its nose for the purpose of having a new nose built to replicate the nose that it had while it was a locomotive as part of its plan for restoration. However, that restoration never came. It sat in outdoor storage in a very forlorn state at the Sacramento Locomotive Works until it was sold to the Pacific Locomotive Association, along with several pieces of rolling stock. They were moved by the Union Pacific Railroad in summer 2008 from Sacramento to their interchange with Niles Canyon Railway at Hearst in Sunol, California. The Niles Canyon Railway then transferred it to its Brightside Yard. Its restoration is underway by volunteers of the PLA. Initial plans called for cosmetic restoration, including building a replica of the locomotive's original nose, and returning the locomotive to its original number, 9010.In 2013 the PLA was able to obtain a set of Krauss Maffei trucks from a retired Plasser and Theurer ballast cleaning machine from France. In 2015, they purchased replacement cardan shafts made by the Welte group in Germany. These two developments meant that if the rear Maybach could be made operational that it would be possible for SP 9010 to operate under its own power. On February 14, 2017, the rear MD870 Maybach V-16 diesel engine was successfully started after being unused for 48 years. It ran for about 16 minutes; the engine was turned off, then turned back on for 2 minutes with no problems both static runs, and with a clean exhaust. On March 1, 2017, SP 9010 operated under its own power for the first time, on the Niles Canyon Railway. Finally, on July 20, 2019, No. 9010 made its excursion debut on the railway.