Mallet locomotive


The Mallet locomotive is a type of articulated steam railway locomotive, invented by the Swiss engineer Anatole Mallet.
The articulation was achieved by supporting the front of the locomotive on an extended Bissel truck. The compound steam system fed steam at boiler pressure to high-pressure cylinders driving the main set of wheels. The exhaust steam from these cylinders was fed into a low-pressure receiver and was then sent to low-pressure cylinders that powered the driving wheels on the swiveling bogie.

Compounding

Steam under pressure is converted into mechanical energy more efficiently if it is used in a compound engine; in such an engine steam from a boiler is used in high-pressure cylinders and then under reduced pressure in a second set of cylinders. The lower-pressure steam occupies a larger volume and the low-pressure cylinders are larger than the high-pressure cylinders.
A third stage may be employed. Compounding was proposed by the British engineer Jonathan Hornblower in 1781.
The American engineer W. S. Hudson patented a system of compounding for railway locomotives in 1873 in which he proposed an intermediate receiver surrounded by hot gas from the fire, so that the low-pressure steam is partly superheated.
Mallet himself proposed cross-compounding in which a conventional steam locomotive configuration would have one high-pressure cylinder and one low-pressure cylinder.
Mallet patented such a system in 1874, and in 1876 the first locomotive on his principle was built: an 0-4-2T for the Bayonne and Biarritz Railway, and several others followed for railways in mainland Europe.
The London and North Western Railway locomotive engineer F W Webb adopted the idea and converted some existing locomotives in 1879, followed by de Glehn and others in the 1880s and several American engineers in the 1890s which included some vertical boiler railcar applications.

Articulation

Mallet found typical main line railways unwilling to adopt his particular ideas and, in 1884, he started to propose compounding combined with articulation; on lightly engineered secondary lines this could give greater power to locomotives whose axle load and size was limited. His patent 162876 in France specified four cylinders, two large and two small, with one pair of cylinders acting on two or three fixed axles, and the other pair acting on axles mounted in a swivelling truck.
Diagrams provided by Mallet make it clear that the swivelling truck was to be a Bissell truck, that is, a pony truck or bogie pivoting about a vertical pin some distance behind the centre of the truck itself. The weight of the front part of the boiler was to be supported on an arc-shaped radial bearing. The truck could therefore turn into a curve and move to some extent laterally. Typically the support bearing was placed beneath the smokebox, hollowed and with a sliding seal to provide a route for exhaust steam from the low-pressure cylinders to discharge through a blastpipe within the smoke box.
Mallet considered that the major advantage of this arrangement was that it enabled the cylinders on the truck to be fed with low-pressure steam: the high-pressure cylinders were on the fixed main frame and only low-pressure steam needed to be carried through movable pipes to the swivelling truck.

The Mallet concept

This then was what became understood as a "Mallet" locomotive: an articulated locomotive in which the rear set of driving wheels were fixed in the main frame of the locomotive; a Bissell truck carrying a second set of driving wheels; and compounding in which the high-pressure cylinders drove the axles on the main frame and the Bissell truck axles were driven by low-pressure steam.
Mallet asserted that the advantages of his concept were:
The large-diameter pipe conveying the low-pressure steam from the high-pressure to the low-pressure cylinders acted also as a receiver, forming a buffer for the gas flow.
Independent cut-offs for the high-pressure and low-pressure cylinders were advocated by Mallet, but driving standards were inadequate and he later used combined cut-off control.

European versions

Large numbers of Mallet designs for narrow gauge railways were built, but in 1889 the first six standard gauge examples were built by J A Maffei for the Swiss Central railways, and an 87 tonne 0-6-6-0T banker for the Gotthard Bahn, the last being the most powerful and heaviest locomotive in the world at the time. By 1892 110 Mallets were at work, of which 24 were standard gauge; by 1900 there were nearly 400, of which 218 were on standard gauge or Russian gauge.
One of the examples in Germany were the 0-8-8-0Ts built by Maffei for Bavarian State Railways between 1913 and 1923. However no Mallet ever ran on a British railway.
Mallet designs were popular in Hungary, too. 30 of were built between 1898–1902. was a B locomotive in service between 1905–1969 and until 1962. The strongest Mallet-locomotive of Europe was the MÁV 601 which was built for the Hungarian State Railways, it as a C type steam locomotive. With their 22.5 meter length, 163.3 tonnes total weight and 2200 KW power, the MÁV 601 was the biggest, the heaviest and most powerful steam locomotive built before and during the First World War in Europe.

North American usage

The first US example was Baltimore & Ohio Railroad number 2400, built by Alco in 1904. Nicknamed "Old Maude", it was a 0-6-6-0 weighing and with axle loads of. Received negatively at first due to speed limitation arising from the short wheelbase and stiff suspension, it gained support during service, and it was soon followed by Baldwin examples, and then steadily heavier and more powerful successors.
In Canada, the Canadian Pacific Railway experimented with an unusual design of Mallet promoted by H.H. Vaughan, then Chief Mechanical Officer and Assistant to the CPR Vice-President. Their in-house compound 0-6-6-0 design located both the high and low pressure cylinders adjacent to one another in the center of the locomotive driving opposite directions. Produced in the CPR's Angus shops, road numbers #1950-#1954 were outshopped between 1909 and 1911. An additional
"simple" unit with road #1955 featuring the same arrangement was also produced. These were used in helper service in the Rockies and Selkirks. The units were unpopular with crews owing to frequent steam leakages and derailments resulting from the lack of pilot wheels. While not an outright failure these were considered an unsuccessful design, and by 1916-1917 these units had been converted to a conventional 2-10-0 arrangement. These six locomotives were ultimately the only articulated locomotives operated by a Canadian railway.
As weight and power and length increased, there were experiments with flexible boiler casings; from 1910 the Santa Fe road introduced 2-6-6-2 locomotives weighing, with a long boiler barrel, with a firetube reheater and a firetube feedwater section in front, each separated by a blank section, and variants of a telescopic or bellows type boiler casing. These were unsuccessful, and later engines used conventional boilers.
The largest compound Mallets were ten 2-10-10-2s built for the Virginian by Alco in 1918; in pairs they pushed coal trains headed by a 2-8-8-2.
The last compound Mallets built in North America were the Norfolk and Western Y6b 2-8-8-2's produced by the Roanoke Shops in 1952. Although compounds had been considered obsolescent since the 1920s, C&O thought them appropriate for low-speed coal-mine pickup runs converging on the classification yard at Russell, Kentucky. Only ten were built before the order was cancelled, the last delivered in September 1949. The final loco, Chesapeake and Ohio 1309, is preserved on the Western Maryland Scenic Railroad. The 1309 was also the very last steam locomotive that Baldwin built for the North American market.

Simple expansion versions in the US

By about 1920 the US version of the Mallet as a huge slow-speed pusher had reached a plateau; the size of the LP cylinders became a limiting factor even on the large loading gauge permitted in the US, and reciprocating masses posed serious dynamic problems above walking pace. Moreover, there were adhesion stability problems where the front engine tended to slip and then stall uncontrollably because of an imbalance of tractive effort and axle load, accentuated by the drawbar reaction, and inability of the intermediate steam receiver to accommodate the sudden pressure change. This was further worsened by dynamic instability of the front end in running.
The Chesapeake & Ohio road introduced 25 simple 2-8-8-2 locomotives in 1924 and 20 more in 1926. Although the simple-expansion concept diverged from Mallet's original patent, the locomotives were clearly a continuation of the concept and were conveniently still referred to as "Mallet" locomotives. As the front truck cylinders were now using boiler pressure steam, special arrangements were necessary to deliver it, through the truck pivot pin where only radial movement took place. These new locomotives took over service on a division, covering it in 5 hours with and a single locomotive.
Further development culminated in 1941 with the 4-8-8-4 Big Boy type on the Union Pacific RR. They weighed with a tender; at long, they could only be turned on a select few of the system's turntables. They could develop on the drawbar at and were designed for a top speed of, though they rarely saw these speeds during their service careers. Slightly shorter but even heavier and more powerful were 2-6-6-6s built by Lima for the C&O and the Virginian between 1941 and 1948, which weighed and could produce up to at.

The last Mallets

These US locomotives were paralleled to some extent by heavy haul versions in the USSR, though without any attempt at faster running. Two 2-8-8-4 examples built in Russia in 1954–55 were probably the last Mallets built in Europe.

Other continents

Although it had found early favour in Europe, especially on lightly engineered railways, the Mallet type had generally been superseded by the Garratt locomotive by the mid-1920s, but in the Dutch East Indies, now the Republic of Indonesia, several types and sizes remained in use into the 1980s. Moreover, in 1962 the Indonesian State railways DKA ordered a series of 0-4-4-2s, basically an updated version of the earlier Dutch design, for the old Atjeh tramway. Constructed by Nippon Sharyo in Japan, these are the only Mallets built in Asia. In contrast to the rest of the Indonesian railways it has a gauge of, as to for the rest of the Archipelago. Smaller Mallets were used by plantations and other industries, all of the 0-4-4-0 type. These ran mostly on and gauge networks. They were employed in Brazilian, tight-radius railroads.
One Mallet ran in New Zealand, and is preserved at Glenbrook Vintage Railway, Auckland. Three Mallets ran in Australia, including one on the Magnet Tramway in Tasmania.

Preservation

Several Mallets have been preserved, some in operational condition. A number of the Union Pacific "Big Boys", are preserved, including one overlooking Omaha, Nebraska where UP is based. In January 2014, Big Boy #4014 was removed from its museum ground parking track in Pomona, California and hauled to Cheyenne, Wyoming for restoration to operating condition; this was completed in May 2019. No. 4014 is the largest, heaviest, and most powerful operational steam locomotive in the world.
Two of Union Pacific's "Challengers" class have also survived into preservation. Challenger #3985 was the largest operational steam locomotive in the world until the restoration of UP 4014. It was taken out of service in October 2010 due to mechanical problems and subsequently retired in January 2020.
Chesapeake & Ohio 2-6-6-2 #1309, the last domestic steam locomotive built by Baldwin, was scheduled for restoration in September 2017, though it has not been completed.
The single surviving example of a Cab forward Mallet is Southern Pacific 4294, which is one display at the California State Railroad Museum in Sacramento, California.
Several smaller loggin railroad Mallets have been restored to operating condition, including Black Hills Central #110 in Hill City, South Dakota, Clover Valley Lumber Company #4 in Sunol, California, and Deep River Logging "Skookum" #7 in Garibaldi, Oregon.
One of the early Dutch-built Indonesian Mallets has been returned to the Netherlands and is now exhibited in the Dutch Railway Museum,
Another industrial type has been purchased and restored by the Statfold Barn Railway in the UK. This saw its first operation in Europe in 2011 and after initial trials on the owners' railway, was transferred to the Welsh Highland Railway as its power is better suited to that railway.
A number of Mallets were constructed for the Nordhausen Wernigerode Eisenbahn, now part of the Harz Narrow Gauge Railways system in Germany.Running numbers 99 5901-3 and number 99 5906 are in working order.
ABPF-SC has restored a Mallet to working order. It hauls tourist steam trains on 3% grades. The first official train ran on April 30 2017.

Terminology

As a French-speaking Swiss, Mallet pronounced his name accordingly, something like "Ma-lay".
Mallet's original patent specifies compound expansion, but after his death in 1919 many locomotives were articulated Mallet style without using compounding. When fleets of such locomotives appeared in the middle 1920s the trade press naturally called them "Simple Mallets" — i.e., simple locomotives articulated like Mallets — but eventually the notion spread that this was somehow incorrect. The term "Mallet" continued to be widely used for simples as well as compounds, but some enthusiasts insist "simple Mallet" is an oxymoron.