Post-perovskite is a high-pressure phase of magnesium silicate. It is composed of the prime oxide constituents of the Earth's rocky mantle, and its pressure and temperature for stability imply that it is likely to occur in portions of the lowermost few hundred km of Earth's mantle. The post-perovskite phase has implications for the D′′ layer, which influences the convective mixing in the mantle responsible for plate tectonics. Post-perovskite has the same crystal structure as the synthetic solid compound CaIrO3, and is often referred to as the "CaIrO3-type phase of MgSiO3" in the literature. The crystal system of post-perovskite is orthorhombic, its space group is Cmcm, and its structure is a stacked SiO6-octahedral sheet along the b axis. The name "post-perovskite" derives from silicate perovskite, the stable phase of MgSiO3 throughout most of Earth's mantle, which has the perovskite structure. The prefix "post-" refers to the fact that it occurs after perovskite structured MgSiO3 as pressure increases. At upper mantle pressures, nearest Earth's surface, MgSiO3 persists as the silicate mineralenstatite, a pyroxene rock forming mineral found in igneous and metamorphic rocks of the crust.
History
The CaIrO3-type phase of MgSiO3 phase was discovered in 2004 using the laser-heated diamond anvil cell technique by a group at the Tokyo Institute of Technology and, independently, by researchers from the Swiss Federal Institute of Technology and Japan Agency for Marine-Earth Science and Technology who used a combination of quantum-mechanical simulations and LHDAC experiments. The TIT group's paper appeared in the journal Science. The ETH/JAM-EST collaborative paper and TIT group's second paper appeared two months later in the journal Nature. This simultaneous discovery was preceded by S. Ono's experimental discovery of a similar phase, possessing exactly the same structure, in Fe2O3.
Importance in Earth's mantle
Post-perovskite phase is stable above 120 GPa at 2500 K, and exhibits a positive Clapeyron slope such that the transformation pressure increases with temperature. Because these conditions correspond to a depth of about 2600 km and the D" seismic discontinuity occurs at similar depths, the perovskite to post-perovskite phase change is considered to be the origin of such seismic discontinuities in this region. Post-perovskite also holds great promise for mapping experimentally determined information regarding the temperatures and pressures of its transformation into direct information regarding temperature variations in the D" layer once the seismic discontinuities attributed to this transformation have been sufficiently mapped out. Such information can be used, for example, to: For these reasons the finding of the MgSiO3-post-perovskite phase transition is considered by many geophysicists to be the most important discovery in deep Earth science in several decades, and was only made possible by the concerted efforts of mineral physics scientists around the world as they sought to increase the range and quality of LHDAC experiments and as ab initio calculations attained predictive power.
Physical properties
The sheet structure of post-perovskite makes the compressibility of the b axis higher than that of the a or c axis. This anisotropy may yield the morphology of a platy crystal habit parallel to the plane; the seismic anisotropy observed in the D" region might qualitatively be explained by this characteristic. Theory predicted the slip associated with particularly favorable stacking faults and confirmed by later experiments. Some theorists predicted other slip systems, which await experimental confirmation. In 2005 and 2006 Ono and Oganov published two papers predicting that post-perovskite should have high electrical conductivity, perhaps two orders of magnitude higher than perovskite's conductivity. In 2008 Hirose's group published an experimental report confirming this prediction. A highly conductive post-perovskite layer provides an explanation for the observed decadal variations of the length of day.
Chemical properties
Another potentially important effect that needs to be better characterized for the post-perovskite phase transition is the influence of other chemical components that are known to be present to some degree in Earth's lowermost mantle. The phase transition pressure, was initially thought to decrease as the FeO content increases, but some recent experiments suggest the opposite. However, it is possible that the effect of Fe2O3 is more relevant as most of iron in post-perovskite is likely to be trivalent. Such components as Al2O3 or the more oxidized Fe2O3 also affect the phase transition pressure, and might have strong mutual interactions with one another. The influence of variable chemistry present in the Earth's lowermost mantle upon the post-perovskite phase transition raises the issue of both thermal and chemical modulation of its possible appearance in the D" layer.
Summary
Experimental and theoretical work on the perovskite/post-perovskite phase transition continues, while many important features of this phase transition remain ill-constrained. For example, the Clapeyron slope describing the increase in the pressure of the phase transition with increasing temperature is known to be relatively high in comparison to other solid-solid phase transitions in the Earth's mantle, however, the experimentally determined value varies from about 5 MPa/K to as high as 13 MPa/K. Ab initio calculations give a tighter range, between 7.5 MPa/K and 9.6 MPa/K, and are probably the most reliable estimates available today. The difference between experimental estimates arises primarily because different materials were used as pressure standards in Diamond Anvil Cell experiments. A well-characterized equation of state for the pressure standard, when combined with high energy synchrotron generated X-ray diffraction patterns of the pressure standard, yields information on the pressure-temperature conditions of the experiment. However, as these extreme pressures and temperatures have not been sufficiently explored in experiments, the equations of state for many popular pressure standards are not yet well characterized and often yield different results. Another source of uncertainty in LHDAC experiments is the measurement of temperature from a sample's thermal radiation, which is required to obtain the pressure from the equation of state of the pressure standard. In laser-heated experiments at such high pressures, the samples are necessarily small and numerous approximations are required to obtain estimates of the temperature.
