Thermal runaway
Thermal runaway occurs in situations where an increase in temperature changes the conditions in a way that causes a further increase in temperature, often leading to a destructive result. It is a kind of uncontrolled positive feedback.
In other words, "thermal runaway" describes a process which is accelerated by increased temperature, in turn releasing energy that further increases temperature. In chemistry, it is associated with strongly exothermic reactions that are accelerated by temperature rise. In electrical engineering, thermal runaway is typically associated with increased current flow and power dissipation, although exothermic chemical reactions can be of concern here too. Thermal runaway can occur in civil engineering, notably when the heat released by large amounts of curing concrete is not controlled. In astrophysics, runaway nuclear fusion reactions in stars can lead to nova and several types of supernova explosions, and also occur as a less dramatic event in the normal evolution of solar mass stars, the "helium flash".
Some climate researchers have postulated that a global average temperature increase of 3–4 degrees Celsius above the preindustrial baseline could lead to a further unchecked increase in surface temperatures. For example, releases of methane, a greenhouse gas more potent than CO2, from wetlands, melting permafrost and continental margin seabed clathrate deposits could be subject to positive feedback.
Chemical engineering
Thermal runaway is also called thermal explosion in chemical engineering, or runaway reaction in organic chemistry. It is a process by which an exothermic reaction goes out of control: the reaction rate increases due to an increase in temperature, causing a further increase in temperature and hence a further rapid increase in the reaction rate. This has contributed to industrial chemical accidents, most notably the 1947 Texas City disaster from overheated ammonium nitrate in a ship's hold, and the 1976 explosion of zoalene, in a drier, at King's Lynn. Frank-Kamenetskii theory provides a simplified analytical model for thermal explosion. Chain branching is an additional positive feedback mechanism which may also cause temperature to skyrocket because of rapidly increasing reaction rate.Chemical reactions are either endothermic or exothermic, as expressed by their change in enthalpy. Many reactions are highly exothermic, so many industrial-scale and oil refinery processes have some level of risk of thermal runaway. These include hydrocracking, hydrogenation, alkylation, oxidation, metalation and nucleophilic aromatic substitution. For example, oxidation of cyclohexane into cyclohexanol and cyclohexanone and ortho-xylene into phthalic anhydride have led to catastrophic explosions when reaction control failed.
Thermal runaway may result from unwanted exothermic side reaction that begin at higher temperatures, following an initial accidental overheating of the reaction mixture. This scenario was behind the Seveso disaster, where thermal runaway heated a reaction to temperatures such that in addition to the intended 2,4,5-trichlorophenol, poisonous 2,3,7,8-tetrachlorodibenzo-p-dioxin was also produced, and was vented into the environment after the reactor's rupture disk burst.
Thermal runaway is most often caused by failure of the reactor vessel's cooling system. Failure of the mixer can result in localized heating, which initiates thermal runaway. Similarly, in flow reactors, localized insufficient mixing causes hotspots to form, wherein thermal runaway conditions occur, which causes violent blowouts of reactor contents and catalysts. Incorrect equipment component installation is also a common cause. Many chemical production facilities are designed with high-volume emergency venting, a measure to limit the extent of injury and property damage when such accidents occur.
At large scale, it is unsafe to "charge all reagents and mix", as is done in laboratory scale. This is because the amount of reaction scales with the cube of the size of the vessel, but the heat transfer area scales with the square of the size, so that the heat production-to-area ratio scales with the size. Consequently, reactions that easily cool fast enough in the laboratory can dangerously self-heat at ton scale. In 2007, this kind of erroneous procedure caused an explosion of a -reactor used to metalate methylcyclopentadiene with metallic sodium, causing the loss of four lives and parts of the reactor being flung away. Thus, industrial scale reactions prone to thermal runaway are preferably controlled by the addition of one reagent at a rate corresponding to the available cooling capacity.
Some laboratory reactions must be run under extreme cooling, because they are very prone to hazardous thermal runaway. For example, in Swern oxidation, the formation of sulfonium chloride must be performed in a cooled system, because at room temperature the reaction undergoes explosive thermal runaway.
Microwave heating
s are used for heating of various materials in cooking and various industrial processes. The rate of heating of the material depends on the energy absorption, which depends on the dielectric constant of the material. The dependence of dielectric constant on temperature varies for different materials; some materials display significant increase with increasing temperature. This behavior, when the material gets exposed to microwaves, leads to selective local overheating, as the warmer areas are better able to accept further energy than the colder areas—potentially dangerous especially for thermal insulators, where the heat exchange between the hot spots and the rest of the material is slow. These materials are called thermal runaway materials. This phenomenon occurs in some ceramics.Electrical engineering
Some electronic components develop lower resistances or lower triggering voltages as their internal temperature increases. If circuit conditions cause markedly increased current flow in these situations, increased power dissipation may raise the temperature further by Joule heating. A vicious circle or positive feedback effect of thermal runaway can cause failure, sometimes in a spectacular fashion. To prevent these hazards, well-designed electronic systems typically incorporate current limiting protection, such as thermal fuses, circuit breakers, or PTC current limiters.To handle larger currents, circuit designers may connect multiple lower-capacity devices in parallel. This technique can work well, but is susceptible to a phenomenon called current hogging, in which the current is not shared equally across all devices. Typically, one device may have a slightly lower resistance, and thus draws more current, heating it more than its sibling devices, causing its resistance to drop further. The electrical load ends up funneling into a single device, which then rapidly fails. Thus, an array of devices may end up no more robust than its weakest component.
The current-hogging effect can be reduced by carefully matching the characteristics of each paralleled device, or by using other design techniques to balance the electrical load. However, maintaining load balance under extreme conditions may not be straightforward. Devices with an intrinsic positive temperature coefficient of electrical resistance are less prone to current hogging, but thermal runaway can still occur because of poor heat sinking or other problems.
Many electronic circuits contain special provisions to prevent thermal runaway. This is most often seen in transistor biasing arrangements for high-power output stages. However, when equipment is used above its designed ambient temperature, thermal runaway can still occur in some cases. This occasionally causes equipment failures in hot environments, or when air cooling vents are blocked.
Semiconductors
shows a peculiar profile, in that its electrical resistance increases with temperature up to about 160 °C, then starts decreasing, and drops further when the melting point is reached. This can lead to thermal runaway phenomena within internal regions of the semiconductor junction; the resistance decreases in the regions which become heated above this threshold, allowing more current to flow through the overheated regions, in turn causing yet more heating in comparison with the surrounding regions, which leads to further temperature increase and resistance decrease. This leads to the phenomenon of current crowding and formation of current filaments, and is one of the underlying causes of many semiconductor junction failures.Bipolar junction transistors (BJTs)
increases significantly in bipolar transistors as they increase in temperature. Depending on the design of the circuit, this increase in leakage current can increase the current flowing through a transistor and thus the power dissipation, causing a further increase in collector-to-emitter leakage current. This is frequently seen in a push-pull stage of a class AB amplifier. If the pull-up and pull-down transistors are biased to have minimal crossover distortion at room temperature, and the biasing is not temperature-compensated, then as the temperature rises both transistors will be increasingly biased on, causing current and power to further increase, and eventually destroying one or both devices.One rule of thumb to avoid thermal runaway is to keep the operating point of a BJT so that Vce ≤ 1/2Vcc
Another practice is to mount a thermal feedback sensing transistor or other device on the heat sink, to control the crossover bias voltage. As the output transistors heat up, so does the thermal feedback transistor. This in turn causes the thermal feedback transistor to turn on at a slightly lower voltage, reducing the crossover bias voltage, and so reducing the heat dissipated by the output transistors.
If multiple BJT transistors are connected in parallel, a current hogging problem can occur. Special measures must be taken to control this characteristic vulnerability of BJTs.
In power transistors, current hogging can occur between different parts of the transistor itself, with one part of the transistor becoming more hot than the others. This is called second breakdown, and can result in destruction of the transistor even when the average junction temperature seems to be at a safe level.
Power MOSFETs
Power MOSFETs typically increase their on-resistance with temperature. Under some circumstances, power dissipated in this resistance causes more heating of the junction, which further increases the junction temperature, in a positive feedback loop. As a consequence, power MOSFETs have stable and unstable regions of operation. However, the increase of on-resistance with temperature helps balance current across multiple MOSFETs connected in parallel, so current hogging does not occur. If a MOSFET transistor produces more heat than the heatsink can dissipate, then thermal runaway can still destroy the transistors. This problem can be alleviated to a degree by lowering the thermal resistance between the transistor die and the heatsink. See also Thermal Design Power.Metal oxide varistors (MOVs)
Metal oxide varistors typically develop lower resistance as they heat up. If connected directly across an AC or DC power bus, a MOV which has developed a lowered trigger voltage can slide into catastrophic thermal runaway, possibly culminating in a small explosion or fire. To prevent this possibility, fault current is typically limited by a thermal fuse, circuit breaker, or other current limiting device.Tantalum capacitors
s are, under some conditions, prone to self-destruction by thermal runaway. The capacitor typically consists of a sintered tantalum sponge acting as the anode, a manganese dioxide cathode, and a dielectric layer of tantalum pentoxide created on the tantalum sponge surface by anodizing. It may happen that the tantalum oxide layer has weak spots that undergo dielectric breakdown during a voltage spike. The tantalum sponge then comes into direct contact with the manganese dioxide, and increased leakage current causes localized heating; usually, this drives an endothermic chemical reaction that produces manganese oxide and regenerates the tantalum oxide dielectric layer.However, if the energy dissipated at the failure point is high enough, a self-sustaining exothermic reaction can start, similar to the thermite reaction, with metallic tantalum as fuel and manganese dioxide as oxidizer. This undesirable reaction will destroy the capacitor, producing smoke and possibly flame.
Therefore, tantalum capacitors can be freely deployed in small-signal circuits, but application in high-power circuits must be carefully designed to avoid thermal runaway failures.
Digital logic
The leakage current of logic switching transistors increases with temperature. In rare instances, this may lead to thermal runaway in digital circuits. This is not a common problem, since leakage currents usually make up a small portion of overall power consumption, so the increase in power is fairly modest — for an Athlon 64, the power dissipation increases by about 10% for every 30 degrees Celsius. For a device with a TDP of 100 W, for thermal runaway to occur, the heat sink would have to have a thermal resistivity of over 3 K/W, which is about 6 times worse than a stock Athlon 64 heat sink. Regardless, an inadequate heat sink with a thermal resistance of over 0.5 to 1 K/W would result in the destruction of a 100 W device even without thermal runaway effects.Batteries
When handled improperly, or if manufactured defectively, some rechargeable batteries can experience thermal runaway resulting in overheating. Sealed cells will sometimes explode violently if safety vents are overwhelmed or nonfunctional. Especially prone to thermal runaway are lithium-ion batteries, most markedly in the form of the lithium polymer battery. Reports of exploding cellphones occasionally appear in newspapers. In 2006, batteries from Apple, HP, Toshiba, Lenovo, Dell and other notebook manufacturers were recalled because of fire and explosions. The Pipeline and Hazardous Materials Safety Administration of the U.S. Department of Transportation has established regulations regarding the carrying of certain types of batteries on airplanes because of their instability in certain situations. This action was partially inspired by a cargo bay fire on a UPS airplane.One of the possible solutions is in using safer and less reactive anode and cathode materials — thereby avoiding the cobalt electrodes in many lithium rechargeable cells — together with non-flammable electrolytes based on ionic liquids.