Ultra 80


The Sun Microsystems Ultra 80 is a computer workstation that shipped from November 1999 to 2002.
Its enclosure is a fairly large and heavy tower design. At launch, it shipped with Solaris 2.5.1, and was available in a variety of different configurations, with one, two or four 64-bit UltraSPARC II CPUs and up to 4 GB of RAM. When released, the Ultra 80 was Sun's highest performance workstation.
The Ultra 80 is similar to the lower-cost Sun Ultra 60, but is somewhat larger and supports more CPUs and memory. Although it was designed as a workstation rather than a server, it may be rack mounted using an optional kit. The Enterprise 420R is a server product based on the Ultra 80 motherboard in a specialized rack-mountable chassis, with custom power supplies and other parts more appropriate for server applications.
The last order date for the Ultra 80 was July 2002 and the last model stopped shipping in October 2002. The later Ultra 45, introduced in 2006, supports a maximum of two CPUs, rather than the four of the Ultra 80.

Operating system

The Ultra 80 shipped with Solaris 2.5.1, and is capable running later versions of Solaris through Solaris 10, as well as Linux and various other UNIX operating systems. The Ultra 80 cannot run Microsoft Windows directly, although an internal PCI card from Sun could be fitted to allow the use of Windows.

Hardware specifications and notes

Full specifications can be found on the Sun web site.

CPU

Although only sold with either one, two, or four CPUs, the use of three CPUs is a supported configuration. The CPUs run at 450 MHz and have 16-KB data and 16-KB instruction cache on chip with a secondary 4-MB external cache. The X1195A is the part number of one of the CPUs. Each CPU has an integrated floating point processor.

Memory

The Ultra 80 uses 144-pin 5V 60-ns DIMM memory modules of either 64 or 256 MB, which should be installed in sets of four identical DIMMs. There are 16 DIMM sockets, so it is possible to fit up to 4 GB with 16 256 MB modules. The memory bus is 576 bits wide; 512 bits are used for data and 64 bits for error correction. The specifications list a maximum throughput of 1.78-GB/s. Performance is improved if 2-way interleaving is used and maximum performance is achieved with 4-way interleaving, in which case all 16 memory slots would be used, providing the machine with 1 GB or 4 GB of RAM.
Half of the Ultra 80's memory must be fitted on the motherboard and the other half on a memory riser board. Care is needed in handling the memory riser board, as the connector is not designed for repeated use. It must be tightened using a torque wrench supplied with the Ultra 80, as detailed in the service manual.

Internal storage

The Ultra 80 takes one or two 1" high SCA SCSI disk drives internally. It was sold with 18.2-GB or 36.4-GB disks, but can in practice use any SCA disk. The internal disks must be mounted in a carrier or spud-bracket. The SCSI IDs of the internal disks are 0 and 3. These are set by the SCA backplane and cannot be changed.
An optional 1.44 MB 3.5" MS-DOS/IBM compatible floppy drive can be fitted. The Ultra 80 could be purchased new with an optional 12/24 GB DDS-3 tape drive, but will work with a DDS-4 drive, and probably larger tape drives. An optional 644 MB SunCD 32X-speed, Photo CD compatible CD-ROM drive or an optional 10X DVD-ROM could be specified as well. 3rd-party rewritable CD-ROM drives could also be used..

PCI and UPA slots

The Ultra 80 has four full-size slots compliant with PCI specification version 2.1:
Some systems might be inoperable if a PCI 2.2 card is installed.

Framebuffer

There are two UPA graphics slots running at 112 MHz, supporting one or two Elite3D m3 and/or Elite3D m6 graphics options. The popular Creator3D framebuffer is not supported, but will usually work. Some Ultra 80s were sold with the PGX32 framebuffer, even though its low performance made it more appropriate for use in server rather than workstation applications. Although not sold with the Ultra 80s, the later XVR series framebuffers also work, as do the Expert3D series.

SCSI

The Sun Ultra 80 is fitted with a dual channel Ultra-3 SCSI controller. The speed is 40 MB/s. One controller is used for the internal disk and CD-ROM, DVD-ROM and tape. The second channel is used for the external 68-pin Ultra wide SCSI connector on the rear of the Ultra 80.

Input and output connectors

The Sun Ultra 80 has
1 Gb/s Ethernet can be used with the optional Sun X1141A Ethernet card. USB is not officially supported, but various USB boards for PCs have been known to work with Linux and Solaris.

Power consumption

Maximum power consumption is documented as 380W; the components list specifies a Sony 670W 12A power supply.

Construction quality

The Ultra 80 is a well-built workstation. It does not use cheap mass-produced commodity PC parts like some of Sun's Ultra workstations such as the Ultra 5 and Ultra 10. It is very well cooled, suffering none of the overheating problems of Sun's previous quad-processor machine, the SPARCstation 20.

Support

Support for the Ultra 80 ended in October 2007. In addition to official support, knowledgeable people,, are regular visitors to the , and Usenet newsgroups.

Benchmarks

The guide, gives the following data for the well known SPECint 95 and SPECfp 95 benchmarks, although a search of the web site of the does not show these figures. SPEC ceased use of the benchmark before the Ultra 80 was released, so the last results submitted to their web site are in the , a little over a year before the Ultra 80 was released in November 1999.
Model 1450 Model 2450 Model 4450
SPECint 9519.719.719.7
SPECfp 9527.936.144.6

A number of results for the less-commonly-used SPECfp_rate95 and SPECfp_rate_base95 benchmarks can be found on the SPEC web site and are given below.
Model 1450 Model 2450 Model 4450
SPECfp_rate95
SPECfp_rate_base95