USB-C
USB-C is a 24-pin USB connector system with a rotationally symmetrical connector.
The USB Type-C Specification 1.0 was published by the USB Implementers Forum and was finalized in August 2014. It was developed at roughly the same time as the USB 3.1 specification. In July 2016, it was adopted by the IEC as "IEC 62680-1-3".
A device with a Type-C connector does not necessarily implement USB, USB Power Delivery, or any Alternate Mode: the Type-C connector is common to several technologies while mandating only a few of them.
USB 3.2, released in September 2017, replaces the USB 3.1 standard. It preserves existing USB 3.1 SuperSpeed and SuperSpeed+ data modes and introduces two new SuperSpeed+ transfer modes over the USB-C connector using two-lane operation, with data rates of 10 and 20 Gbit/s.
USB4, released in 2019, is the first USB transfer protocol standard that is only available via USB-C.
Overview
USB-C connectors and cables connect to both hosts and devices, replacing various electrical connectors including USB-B and USB-A, HDMI, DisplayPort and 3.5 mm audio cables and connectors.Name
USB Type-C and USB-C are trademarks of USB Implementers Forum.Connectors
The 24-pin double-sided connector is slightly larger than the micro-B connector, with a USB-C port measuring by. Two kinds of connectors exist, female and male.Plugs are found on cables and adapters. Receptacles are found on devices and adapters.
Cables
USB 3.1 cables are considered full-featured USB-C cables. They are electronically marked cables that contain a chip with an ID function based on the configuration channel and vendor-defined messages from the USB Power Delivery 2.0 specification. Cable length should be ≤2m for Gen 1 or ≤1m for Gen 2. The electronic ID chip provides information about product/vendor, cable connectors, USB signalling protocol, passive/active construction, use of VCONN power, available VBUS current, latency, RX/TX directionality, SOP controller mode, and hardware/firmware version.USB-C cables that do not have shielded SuperSpeed pairs, sideband use pins, or additional wires for power lines can have increased cable length, up to 4m. These USB-C cables only support 2.0 speeds and do not support alternate modes.
All USB-C cables must be able to carry a minimum of 3 A current but can also carry high-power 5 A current. USB-C to USB-C cables supporting 5A current must contain e-marker chips programmed to identify the cable and its current capabilities. USB Charging ports should also be clearly marked with capable power wattage.
Full-featured USB-C cables that implement USB 3.1 Gen 2 can handle up to 10Gbit/s data rate at full duplex. They are marked with a SuperSpeed+ logo. There are also cables which can carry only USB 2.0 with up to 480Mbit/s data rate. There are USB-IF certification programs available for USB-C products and end users are recommended to use USB-IF certified cables.
Devices
Devices may be hosts or peripherals. Some, such as mobile phones, can take either role depending on what kind is detected on the other end. These types of ports are called Dual-Role-Data ports, which was known as USB On-The-Go in the previous specification. When two such devices are connected, the roles are randomly assigned but a swap can be commanded from either end, although there are optional path and role detection methods that would allow devices to select a preference for a specific role. Furthermore, dual-role devices that implement USB Power Delivery may independently and dynamically swap data and power roles using the Data Role Swap or Power Role Swap processes. This allows for charge-through hub or docking station applications where the USB-C device acts as a USB data host while acting as a power consumer rather than a source.USB-C devices may optionally provide or consume bus power currents of 1.5 A and 3.0 A in addition to baseline bus power provision; power sources can either advertise increased USB current through the configuration channel, or they can implement the full USB Power Delivery specification using both BMC-coded configuration line and legacy BFSK-coded VBUS line.
Connecting an older device to a host with a USB-C receptacle requires a cable or adapter with a USB-A or USB-B plug or receptacle on one end and a USB-C plug on the other end. Legacy adapters with a USB-C receptacle are "not defined or allowed" by the specification because they can create "many invalid and potentially unsafe" cable combinations.
Modes
Audio Adapter Accessory Mode
A device with a USB-C port may support analog headsets through an audio adapter with a 3.5 mm jack, providing four standard analog audio connections. The audio adapter may optionally include a USB-C charge-through port to allow 500 mA device charging. The engineering specification states that an analog headset shall not use a USB-C plug instead of a 3.5 mm plug. In other words, headsets with a USB-C plug should always support digital audio.Analog signals use the USB 2.0 differential pairs and the two side-band use pairs for Mic and GND. The presence of the audio accessory is signalled through the configuration channel and VCONN.
Alternate Mode
An Alternate Mode dedicates some of the physical wires in a USB-C 3.1 cable for direct device-to-host transmission of alternate data protocols. The four high-speed lanes, two side-band pins, and two USB 2.0 data pins and one configuration pin can be used for alternate mode transmission. The modes are configured using vendor-defined messages through the configuration channel.Specifications
USB Type-C Cable and Connector Specification
The USB Type-C specification 1.0 was published by the USB Implementers Forum and was finalized in August 2014.It defines requirements for cables and connectors.
- Rev 1.1 was published 2015-04-03
- Rev 1.2 was published 2016-03-25
- Rev 1.3 was published 2017-07-14
- Rev 1.4 was published 2019-03-29
- Rev 2.0 was published 2019-08
- IEC 62680-1-3:2016 "Universal serial bus interfaces for data and power – Part 1-3: Universal Serial Bus interfaces – Common components – USB Type-C cable and connector specification"
- IEC 62680-1-3:2017 "Universal serial bus interfaces for data and power – Part 1-3: Common components – USB Type-C Cable and Connector Specification"
- IEC 62680-1-3:2018 "Universal serial bus interfaces for data and power – Part 1-3: Common components – USB Type-C Cable and Connector Specification"
Receptacles
| Pin | Name | Description |
| A1 | GND | Ground return |
| A2 | SSTXp1 | SuperSpeed differential pair #1, TX, positive |
| A3 | SSTXn1 | SuperSpeed differential pair #1, TX, negative |
| A4 | VBUS | Bus power |
| A5 | CC1 | Configuration channel |
| A6 | Dp1 | USB 2.0 differential pair, position 1, positive |
| A7 | Dn1 | USB 2.0 differential pair, position 1, negative |
| A8 | SBU1 | Sideband use |
| A9 | VBUS | Bus power |
| A10 | SSRXn2 | SuperSpeed differential pair #4, RX, negative |
| A11 | SSRXp2 | SuperSpeed differential pair #4, RX, positive |
| A12 | GND | Ground return |
| Pin | Name | Description |
| B12 | GND | Ground return |
| B11 | SSRXp1 | SuperSpeed differential pair #2, RX, positive |
| B10 | SSRXn1 | SuperSpeed differential pair #2, RX, negative |
| B9 | VBUS | Bus power |
| B8 | SBU2 | Sideband use |
| B7 | Dn2 | USB 2.0 differential pair, position 2, negative |
| B6 | Dp2 | USB 2.0 differential pair, position 2, positive |
| B5 | CC2 | Configuration channel |
| B4 | VBUS | Bus power |
| B3 | SSTXn2 | SuperSpeed differential pair #3, TX, negative |
| B2 | SSTXp2 | SuperSpeed differential pair #3, TX, positive |
| B1 | GND | Ground return |
Plugs
The male connector has only one high-speed differential pair, and one of the CC pins is replaced by VCONN, to power electronics in the cable, and the other is used to actually carry the Configuration Channel signals. These signals are used to determine the orientation of the cable, as well as to carry USB Power Delivery communications.Cables
Related USB-IF specifications
USB Type-C Locking Connector Specification
The USB Type-C Locking Connector Specification was published 2016-03-09. It defines the mechanical requirements for USB-C plug connectors and the guidelines for the USB-C receptacle mounting configuration to provide a standardized screw lock mechanism for USB-C connectors and cables.USB Type-C Port Controller Interface Specification
The USB Type-C Port Controller Interface Specification was published 2017-10-01. It defines a common interface from a USB-C Port Manager to a simple USB-C Port Controller.USB Type-C Authentication Specification
Adopted as IEC specification:- IEC 62680-1-4:2018 "Universal Serial Bus interfaces for data and power - Part 1-4: Common components - USB Type-C™ Authentication Specification"
USB 2.0 Billboard Device Class Specification
USB Audio Device Class 3.0 Specification
USB Audio Device Class 3.0 defines powered digital audio headsets with a USB-C plug. The standard supports the transfer of both digital and analog audio signals over the USB port.USB Power Delivery Specification
While it is not necessary for USB-C compliant devices to implement USB Power Delivery, for USB-C DRP/DRD ports, USB Power Delivery introduces commands for altering a port's power or data role after the roles have been established when a connection is made.USB 3.2 Specification
, released in September 2017, replaces the USB 3.1 standard. It preserves existing USB 3.1 SuperSpeed and SuperSpeed+ data modes and introduces two new SuperSpeed+ transfer modes over the USB-C connector using two-lane operation, doubling the data rates to 10 and 20 Gbit/s.USB4 Specification
The USB4 specification released in 2019 is the first USB data transfer specification to require USB-C connectors.Alternate Mode partner specifications
five system-defined Alternate Mode partner specifications exist. Additionally, vendors may support proprietary modes for use in dock solutions. Alternate Modes are optional; USB-C features and devices are not required to support any specific Alternate Mode. The USB Implementers Forum is working with its Alternate Mode partners to make sure that ports are properly labelled with respective logos.| Logo | Name | Date | Protocol |
| DisplayPort Alternate Mode | Published in September 2014 | DisplayPort 1.4 | |
| Mobile High-Definition Link Alternate Mode | Announced in November 2014 | MHL 1.0, 2.0, 3.0 and superMHL 1.0 | |
| Thunderbolt Alternate Mode | Announced in June 2015 | Thunderbolt 3 | |
| HDMI Alternate Mode | Announced in September 2016 | HDMI 1.4b | |
| VirtualLink Alternate Mode | Announced in July 2018 | VirtualLink 1.0 |
Other protocols like Ethernet have been proposed.
All Thunderbolt 3 controllers both support "Thunderbolt Alternate Mode" and "DisplayPort Alternate Mode". Because Thunderbolt can encapsulate DisplayPort data, every Thunderbolt controller can either output DisplayPort signals directly over "DisplayPort Alternative Mode" or encapsulated within Thunderbolt in "Thunderbolt Alternate Mode". Low cost peripherals mostly connect via "DisplayPort Alternate Mode" while some docking stations tunnel DisplayPort over Thunderbolt.
The USB SuperSpeed protocol is similar to DisplayPort and PCIe/Thunderbolt, in using packetized data transmitted over differential LVDS lanes with embedded clock using comparable bit rates, so these Alternate Modes are easier to implement in the chipset.
Alternate Mode hosts and sinks can be connected with either regular full-featured USB-C cables, or with converter cables or adapters:
;USB 3.1 Type-C to Type-C full-featured cable: DisplayPort, Mobile High-Definition Link, HDMI and Thunderbolt Alternate Mode USB-C ports can be interconnected with standard passive full-featured USB Type-C cables. These cables are only marked with standard "trident" SuperSpeed USB logo or the SuperSpeed+ USB 10 Gbit/s logo on both ends. Cable length should be 2.0m or less for Gen 1 and 1.0m or less for Gen 2.
;Thunderbolt Type-C to Type-C active cable: Thunderbolt 3 Alternate Mode with cables longer than 0.5 m requires active USB-C cables that are certified and electronically marked for high-speed Thunderbolt 3 transmission, similarly to high-power 5 A cables. These cables are marked with a Thunderbolt logo on both ends. They do not support USB 3 backwards compatibility, only USB 2 or Thunderbolt. Cables can be marked for both Thunderbolt and 5 A power delivery at the same time.
Active cables/adapters contain powered ICs to amplify/equalise the signal for extended length cables, or to perform active protocol conversion. The adapters for video Alt Modes may allow conversion from native video stream to other video interface standards.
Using full-featured USB-C cables for Alternate Mode connections provides some benefits. Alternate Mode does not employ USB 2.0 lanes and the configuration channel lane, so USB 2.0 and USB Power Delivery protocols are always available. In addition, DisplayPort and MHL Alternate Modes can transmit on one, two, or four SuperSpeed lanes, so two of the remaining lanes may be used to simultaneously transmit USB 3.1 data.
USB-C receptacle pin usage in different modes
The diagrams below depict the pins of a USB-C socket in different use cases.USB 2.0/1.1
A simple USB 2.0/1.1 device mates using one pair of D+/D− pins. Hence, the source does not require any connection management circuitry, and therefore USB-C is backward compatible with even the oldest USB devices. V and GND provide 5V up to 500mA of current. However, to connect a USB 2.0/1.1 device to a USB-C host, use of Rd on the CC pins is required, as the source will not supply V until a connection is detected through the CC pins.| GND | TX1+ | TX1− | V | CC1 | D+ | D− | SBU1 | V | RX2− | RX2+ | GND |
| GND | RX1+ | RX1− | V | SBU2 | D− | D+ | CC2 | V | TX2− | TX2+ | GND |
USB Power Delivery
USB Power Delivery uses one of CC1, CC2 pins for power negotiation up to 20 V at 5 A. It is transparent to any data transmission mode, and can therefore be used together with any of them as long as the CC pins are not clobbered.| GND | TX1+ | TX1− | V | CC1 | D+ | D− | SBU1 | V | RX2− | RX2+ | GND |
| GND | RX1+ | RX1− | V | SBU2 | D− | D+ | CC2 | V | TX2− | TX2+ | GND |
USB 3.0/3.1/3.2
In the USB 3.0/3.1/3.2 mode, two or four high speed links are used in TX/RX pairs to provide 5 to 10, or 10 to 20 Gbit/s throughput respectively. One of the CC pins is used to negotiate the mode.V and GND provide 5 V up to 900 mA, in accordance with the USB 3.1 specification. A specific USB-C mode may also be entered, where 5 V at either 1.5 A or 3 A is provided. A third alternative is to establish a Power Delivery contract.
In single-lane mode, only the differential pairs closest to the CC pin are used for data transmission. For dual-lane data transfers, all four differential pairs are in use.
The D+/D− link for USB 2.0/1.1 is typically not used when USB 3.x connection is active, but devices like hubs open simultaneous 2.0 and 3.x uplinks in order to allow operation of both type devices connected to it. Other devices may have fallback mode to 2.0, in case the 3.x connection fails.
| GND | TX1+ | TX1− | V | CC1 | D+ | D− | SBU1 | V | RX2− | RX2+ | GND |
| GND | RX1+ | RX1− | V | SBU2 | D− | D+ | CC2 | V | TX2− | TX2+ | GND |
Alternate Mode
In the Alternate Mode one of up to four high speed links are used in whatever direction is needed. SBU1, SBU2 provide an additional lower speed link. If two high speed links remain unused, then a USB 3.0/3.1 link can be established concurrently to the Alternate Mode. One of the CC pins is used to perform all the negotiation. An additional low band bidirectional channel may share that CC pin as well. USB 2.0 is also available through D+/D− pins.In regard to power, the devices are supposed to negotiate a Power Delivery contract before an alternate mode is entered.
| GND | TX1+ | TX1− | V | CC1 | D+ | D− | SBU1 | V | RX2− | RX2+ | GND |
| GND | RX1+ | RX1− | V | SBU2 | D− | D+ | CC2 | V | TX2− | TX2+ | GND |
Debug Accessory Mode
The external device test system signals to the target system to enter debug accessory mode via CC1 and CC2 both being pulled down with an Rn resistor value or pulled up as Rp resistor value from the test plug.After entering debug accessory mode, optional orientation detection via the CC1 and CC2 is done via setting CC1 as a pullup of Rd resistance and CC2 pulled to ground via Ra resistance. While optional, orientation detection is required if USB Power Delivery communication is to remain functional.
In this mode, all digital circuits are disconnected from the connector, and 14 underlined pins can be used to expose debug related signals. USB IF requires for certification that security and privacy consideration and precaution has been taken and that the user has actually requested that debug test mode be performed.
| GND | TX1+ | TX1− | V | CC1 | D+ | D− | SBU1 | V | RX2− | RX2+ | GND |
| GND | RX1+ | RX1− | V | SBU2 | D− | D+ | CC2 | V | TX2− | TX2+ | GND |
If a reversible Type-C cable is required but Power Delivery support is not, the test plug will need to be arranged as below, with CC1 and CC2 both being pulled down with an Rn resistor value or pulled up as Rp resistor value from the test plug:
| GND | TS1 | TS2 | V | CC1 | TS6 | TS7 | TS5 | V | TS4 | TS3 | GND |
| GND | TS3 | TS4 | V | TS5 | TS7 | TS6 | CC2 | V | TS2 | TS1 | GND |
This mirroring of test signals will only provide 7 test signals for debug usage instead of 14, but with the benefit of minimising extra parts count for orientation detection.
Audio Adapter Accessory Mode
In this mode, all digital circuits are disconnected from the connector, and certain pins become reassigned for analog outputs or inputs. The mode, if supported, is entered when both CC pins are shorted to GND. D− and D+ become audio output left L and right R, respectively. The SBU pins become a microphone pin MIC, and the analog ground AGND, the latter being a return path for both outputs and the microphone. Nevertheless, the MIC and AGND pins must have automatic swap capability, for two reasons: firstly, the USB-C plug may be inserted either side; secondly, there is no agreement, which TRRS rings shall be GND and MIC, so devices equipped with a headphone jack with microphone input must be able to perform this swap anyway.This mode also allows concurrent charging of a device exposing the analog audio interface, however only at 5 V and 500 mA, as CC pins are unavailable for any negotiation.
| GND | TX1+ | TX1− | V | CC1 | R | L | MIC | V | RX2− | RX2+ | GND |
| GND | RX1+ | RX1− | V | AGND | L | R | CC2 | V | TX2− | TX2+ | GND |
Plug insertions detection is performed by the TRRS plug's physical plug detection switch. On plug insertions, this will pull down both CC and VCONN in the plug. This is essentially a direct connection to USB digital ground.
| TRRS socket | Analog audio signal | USB Type-C male plug |
| Tip | L | D− |
| Ring 1 | R | D+ |
| Ring 2 | Microphone/ground | SBU1 or SBU2 |
| Sleeve | Microphone/ground | SBU2 or SBU1 |
| DETECT1 | Plug presence detection switch | CC, VCONN |
| DETECT2 | Plug presence detection switch | GND |
Software support
- Android from version 6.0 onwards works with USB 3.1 and USB-C.
- Chrome OS, starting with the Chromebook Pixel 2015, supports USB 3.1, USB-C, alternate modes, power delivery, and USB Dual-Role support.
- FreeBSD released the Extensible Host Controller Interface, supporting USB 3.0, with release 8.2
- iOS from version 12.1 onwards works with USB-C.
- NetBSD began supporting USB 3.0 with release 7.2
- Linux has supported USB 3.0 since kernel version 2.6.31 and USB version 3.1 since kernel version 4.6.
- OpenBSD began supporting USB 3.0 in version 5.7
- OS X Yosemite, starting with the MacBook Retina early 2015, supports USB 3.1, USB-C, alternate modes, and power delivery.
- Windows 8.1 added USB-C and billboard support in an update.
- Windows 10 and Windows 10 Mobile support USB 3.1, USB-C, alternate modes, billboard device class, power delivery and USB Dual-Role.
Hardware support
USB-C devices
An increasing number of motherboards, notebooks, tablet computers, smartphones, hard disk drives, USB hubs and other devices released from 2014 onwards feature USB-C receptacles. However, further adoption of USB-C is limited by the comparatively high cost of USB-C cables and connectors.Video output
Currently, DisplayPort is the most widely implemented alternate mode, and is used to provide video output on devices that do not have standard-size DisplayPort or HDMI ports, such as smartphones and laptops. A USB-C multiport adapter converts the device's native video stream to DisplayPort/HDMI/VGA, allowing it to be displayed on an external display, such as a television set or computer monitor.It is also used on USB-C docks designed to connect a device to a power source, external display, USB hub, and optional extra with a single cable. These functions are sometimes implemented directly into the display instead of a separate dock, meaning a user connects their device to the display via USB-C with no other connections required.
Compatibility issues
Power issues with cables
Many cables claiming to support USB-C are actually not compliant to the standard. Using these cables would have a potential consequence of damaging devices that they are connected to. There are reported cases of laptops being destroyed due to the use of non-compliant cables.Some non-compliant cables with a USB-C connector on one end and a legacy USB-A plug or Micro-B receptacle on the other end incorrectly terminate the Configuration Channel with a 10kΩ pullup to VBUS instead of the specification mandated 56 kΩ pullup, causing a device connected to the cable to incorrectly determine the amount of power it is permitted to draw from the cable. Cables with this issue may not work properly with certain products, including Apple and Google products, and may even damage power sources such as chargers, hubs, or PC USB ports.
When a defective USB-C cable or power source is used, the voltage seen by a USB-C device can be different from the voltage expected by the device. This may result in an overvoltage on the VBUS pin. Also due to the fine pitch of the USB-C receptacle, the VBUS pin from the cable may contact with the CC pin of the USB-C receptacle resulting in a short-to-VBUS electrical issue due to the fact that the VBUS pin is rated up to 20 V while the CC pins are rated up to 5.5 V. To overcome these issues, USB Type-C port protection must be used between USB-C connector and USB-C Power Delivery controller.
Compatibility with audio adapters
On devices that have omitted the 3.5 mm audio jack, the USB-C port can be used to connect wired accessories such as headphones.There are primarily two types of USB-C adapters and two modes of audio output from devices.
When an active set of USB-C headphones or adapter is used, digital audio is sent through the USB-C port. The conversion by the DAC and amplifier is done inside of the headphones or adapter, instead of on the phone. The sound quality is dependent on the headphones/adapter's DAC. Active adapters with a built-in DAC have near-universal support for devices that output digital and analog audio, adhering to the Audio Device Class 3.0 and Audio Adapter Accessory Mode specifications.
Examples of such active adapters include external USB sound cards and DACs that do not require special drivers, and USB-C to 3.5 mm headphone jack adapters by Apple, Google, Essential, Razer, HTC.
On the other hand, when a passive set of USB-C headphones or adapter is used, analog audio is sent through the USB-C port. The conversion by the DAC and amplifier is done on the phone; the headphones or adapter simply passthrough the signal. The sound quality is dependent on the phone's onboard DAC. Passive adapters without a built-in DAC are only compatible with devices that output analog audio, adhering to the Audio Adapter Accessory Mode specification.
| Supported mode | Specification | Devices | USB-C adapters with DACs | USB-C adapters without DACs |
| Digital audio output | Audio Device Class 3.0 | Google Pixel 2, HTC U11, Essential Phone, Razer Phone etc. | ||
| Analog audio output | Audio Device Class 3.0 Audio Adapter Accessory Mode | Moto Z2 Force, Sony Xperia XZ2, Huawei P20 Pro, LeEco, Xiaomi phones etc. |