Electric locomotive


An electric locomotive is a locomotive powered by electricity from overhead lines, a third rail or on-board energy storage such as a battery or a supercapacitor.
Electric locomotives with on-board fueled prime movers, such as diesel engines or gas turbines, are classed as diesel-electric or gas turbine-electric and not as electric locomotives, because the electric generator/motor combination serves only as a power transmission system.
Electric locomotives benefit from the high efficiency of electric motors, often above 90%. Additional efficiency can be gained from regenerative braking, which allows kinetic energy to be recovered during braking to put power back on the line. Newer electric locomotives use AC motor-inverter drive systems that provide for regenerative braking. Electric locomotives are quiet compared to diesel locomotives since there is no engine and exhaust noise and less mechanical noise. The lack of reciprocating parts means electric locomotives are easier on the track, reducing track maintenance. Power plant capacity is far greater than any individual locomotive uses, so electric locomotives can have a higher power output than diesel locomotives and they can produce even higher short-term surge power for fast acceleration. Electric locomotives are ideal for commuter rail service with frequent stops. Electric locomotives are used on freight routes with consistently high traffic volumes, or in areas with advanced rail networks. Power plants, even if they burn fossil fuels, are far cleaner than mobile sources such as locomotive engines. The power can also come from clean or renewable sources, including geothermal power, hydroelectric power, nuclear power, solar power and wind turbines. Electric locomotives usually cost 20% less than diesel locomotives, their maintenance costs are 25-35% lower, and cost up to 50% less to run.
The chief disadvantage of electrification is the high cost for infrastructure: overhead lines or third rail, substations, and control systems. Public policy in the U.S. interferes with electrification: higher property taxes are imposed on privately owned rail facilities if they are electrified. The EPA regulates exhaust emissions on locomotive and marine engines, similar to regulations on car & freight truck emissions, in order to limit the amount of carbon monoxide, unburnt hydrocarbons, nitric oxides, and soot output from these mobile power sources. Because railroad infrastructure is privately owned in the U.S., railroads are unwilling to make the necessary investments for electrification. In Europe and elsewhere, railway networks are considered part of the national transport infrastructure, just like roads, highways and waterways, so are often financed by the state. Operators of the rolling stock pay fees according to rail use. This makes possible the large investments required for the technically and, in the long-term, also economically advantageous electrification.

History

Direct current

The first known electric locomotive was built in 1837 by chemist Robert Davidson of Aberdeen, and it was powered by galvanic cells. Davidson later built a larger locomotive named Galvani, exhibited at the Royal Scottish Society of Arts Exhibition in 1841. The seven-ton vehicle had two direct-drive reluctance motors, with fixed electromagnets acting on iron bars attached to a wooden cylinder on each axle, and simple commutators. It hauled a load of six tons at four miles per hour for a distance of. It was tested on the Edinburgh and Glasgow Railway in September of the following year, but the limited power from batteries prevented its general use. It was destroyed by railway workers, who saw it as a threat to their job security.
The first electric passenger train was presented by Werner von Siemens at Berlin in 1879. The locomotive was driven by a 2.2 kW, series-wound motor, and the train, consisting of the locomotive and three cars, reached a speed of 13 km/h. During four months, the train carried 90,000 passengers on a 300-metre-long circular track. The electricity was supplied through a third insulated rail between the tracks. A contact roller was used to collect the electricity.
The world's first electric tram line opened in Lichterfelde near Berlin, Germany, in 1881. It was built by Werner von Siemens. Volk's Electric Railway opened in 1883 in Brighton. Also in 1883, Mödling and Hinterbrühl Tram opened near Vienna in Austria. It was the first in the world in regular service powered from an overhead line. Five years later, in the U.S. electric trolleys were pioneered in 1888 on the Richmond Union Passenger Railway, using equipment designed by Frank J. Sprague.
The first electrified Hungarian railway lines were opened in 1887. Budapest : Ráckeve line, Szentendre line, Gödöllő line, Csepel line.
Much of the early development of electric locomotion was driven by the increasing use of tunnels, particularly in urban areas. Smoke from steam locomotives was noxious and municipalities were increasingly inclined to prohibit their use within their limits. The first electrically-worked underground line was the City and South London Railway, prompted by a clause in its enabling act prohibiting the use of steam power. It opened in 1890, using electric locomotives built by Mather and Platt. Electricity quickly became the power supply of choice for subways, abetted by the Sprague's invention of multiple-unit train control in 1897. Surface and elevated rapid transit systems generally used steam until forced to convert by ordinance.
The first use of electrification on an American main line was on a four-mile stretch of the Baltimore Belt Line of the Baltimore and Ohio Railroad in 1895 connecting the main portion of the B&O to the new line to New York through a series of tunnels around the edges of Baltimore's downtown. Parallel tracks on the Pennsylvania Railroad had shown that coal smoke from steam locomotives would be a major operating issue and a public nuisance. Three Bo+Bo units were initially used, at the south end of the electrified section; they coupled onto the locomotive and train and pulled it through the tunnels. Railroad entrances to New York City required similar tunnels and the smoke problems were more acute there. A collision in the Park Avenue tunnel in 1902 led the New York State legislature to outlaw the use of smoke-generating locomotives south of the Harlem River after 1 July 1908. In response, electric locomotives began operation in 1904 on the New York Central Railroad. In the 1930s, the Pennsylvania Railroad, which had introduced electric locomotives because of the NYC regulation, electrified its entire territory east of Harrisburg, Pennsylvania.
The Chicago, Milwaukee, St. Paul and Pacific Railroad, the last transcontinental line to be built, electrified its lines across the Rocky Mountains and to the Pacific Ocean starting in 1915. A few East Coast lines, notably the Virginian Railway and the Norfolk and Western Railway, electrified short sections of their mountain crossings. However, by this point electrification in the United States was more associated with dense urban traffic and the use of electric locomotives declined in the face of dieselization. Diesel shared some of the electric locomotive's advantages over steam and the cost of building and maintaining the power supply infrastructure, which discouraged new installations, brought on the elimination of most main-line electrification outside the Northeast. Except for a few captive systems, by 2000 electrification was confined to the Northeast Corridor and some commuter service; even there, freight service was handled by diesel. Development continued in Europe, where electrification was widespread. 1,500 V DC is still used on some lines near France and 25 kV 50 Hz is used by high-speed trains.

Alternating current

The first practical AC electric locomotive was designed by Charles Brown, then working for Oerlikon, Zürich. In 1891, Brown had demonstrated long-distance power transmission, using three-phase AC, between a hydro-electric plant at Lauffen am Neckar and Frankfurt am Main West, a distance of 280 km. Using experience he had gained while working for Jean Heilmann on steam-electric locomotive designs, Brown observed that three-phase motors had a higher power-to-weight ratio than DC motors and, because of the absence of a commutator, were simpler to manufacture and maintain. However, they were much larger than the DC motors of the time and could not be mounted in underfloor bogies: they could only be carried within locomotive bodies.
In 1894, Hungarian engineer Kálmán Kandó developed a new type 3-phase asynchronous electric drive motors and generators for electric locomotives.
Kandó's early 1894 designs were first applied in a short three-phase AC tramway in Évian-les-Bains, which was constructed between 1896 and 1898.
In 1918, Kandó invented and developed the rotary phase converter, enabling electric locomotives to use three-phase motors whilst supplied via a single overhead wire, carrying the simple industrial frequency single phase AC of the high voltage national networks.
In 1896, Oerlikon installed the first commercial example of the system on the Lugano Tramway. Each 30-tonne locomotive had two motors run by three-phase 750 V 40 Hz fed from double overhead lines. Three-phase motors run at constant speed and provide regenerative braking, and are well suited to steeply graded routes, and the first main-line three-phase locomotives were supplied by Brown in 1899 on the 40 km Burgdorf—Thun line, Switzerland. The first implementation of industrial frequency single-phase AC supply for locomotives came from Oerlikon in 1901, using the designs of Hans Behn-Eschenburg and Emil Huber-Stockar; installation on the Seebach-Wettingen line of the Swiss Federal Railways was completed in 1904. The 15 kV, 50 Hz, 48 tonne locomotives used transformers and rotary converters to power DC traction motors.
Italian railways were the first in the world to introduce electric traction for the entire length of a mainline rather than just a short stretch. The 106 km Valtellina line was opened on 4 September 1902, designed by Kandó and a team from the Ganz works. The electrical system was three-phase at 3 kV 15 Hz. The voltage was significantly higher than used earlier and it required new designs for electric motors and switching devices. The three-phase two-wire system was used on several railways in Northern Italy and became known as "the Italian system". Kandó was invited in 1905 to undertake the management of Società Italiana Westinghouse and led the development of several Italian electric locomotives. During the period of electrification of the Italian railways, tests were made as to which type of power to use: in some sections there was a 3,600 V Hz three-phase power supply, in others there was 1,500 V DC, 3 kV DC and 10 kV AC 45 Hz supply. After WW2, 3 kV DC power was chosen for the entire Italian railway system.
A later development of Kandó, working with both the Ganz works and Societa Italiana Westinghouse, was an electro-mechanical converter, allowing the use of three-phase motors from single-phase AC, eliminating the need for two overhead wires. In 1923, the first phase-converter locomotive in Hungary was constructed on the basis of Kandó's designs and serial production began soon after. The first installation, at 16 kV 50 Hz, was in 1932 on the 56 km section of the Hungarian State Railways between Budapest and Komárom. This proved successful and the electrification was extended to Hegyeshalom in 1934.
In Europe, electrification projects initially focused on mountainous regions for several reasons: coal supplies were difficult, hydroelectric power was readily available, and electric locomotives gave more traction on steeper lines. This was particularly applicable in Switzerland, where almost all lines are electrified. An important contribution to the wider adoption of AC traction came from SNCF of France after World War II. The company had assessed the industrial-frequency AC line routed through the steep Höllental Valley, Germany, which was under French administration following the war. After trials, the company decided that the performance of AC locomotives was sufficiently developed to allow all its future installations, regardless of terrain, to be of this standard, with its associated cheaper and more efficient infrastructure. The SNCF decision, ignoring as it did the of high-voltage DC already installed on French routes, was influential in the standard selected for other countries in Europe.
The 1960s saw the electrification of many European main lines. European electric locomotive technology had improved steadily from the 1920s onwards. By comparison, the Milwaukee Road class EP-2 weighed 240 t, with a power of 3,330 kW and a maximum speed of 112 km/h; in 1935, German E 18 had a power of 2,800 kW, but weighed only 108 tons and had a maximum speed of 150 km/h. On 29 March 1955, French locomotive CC 7107 reached 331 km/h. In 1960 the SJ Class Dm 3 locomotives on Swedish Railways produced a record 7,200 kW. Locomotives capable of commercial passenger service at 200 km/h appeared in Germany and France in the same period. Further improvements resulted from the introduction of electronic control systems, which permitted the use of increasingly lighter and more powerful motors that could be fitted inside the bogies.
In the 1980s, the development of very high-speed service brought further electrification. The Japanese Shinkansen and the French TGV were the first systems for which devoted high-speed lines were built from scratch. Similar programs were undertaken in Italy, Germany and Spain; in the United States the only new mainline service was an extension of electrification over the Northeast Corridor from New Haven, Connecticut, to Boston, Massachusetts, though new electric light rail systems continued to be built.
On 2 September 2006, a standard production Siemens electric locomotive of the Eurosprinter type ES64-U4 achieved, the record for a locomotive-hauled train, on the new line between Ingolstadt and Nuremberg. This locomotive is now employed largely unmodified by ÖBB to haul their Railjet which is however limited to a top speed of 230 km/h due to economic and infrastructure concerns.

Types

An electric locomotive can be supplied with power from
The distinguishing design features of electric locomotives are:
The most fundamental difference lies in the choice of AC or DC. The earliest systems used DC, as AC was not well understood and insulation material for high voltage lines was not available. DC locomotives typically run at relatively low voltage ; the equipment is therefore relatively massive because the currents involved are large in order to transmit sufficient power. Power must be supplied at frequent intervals as the high currents result in large transmission system losses.
As AC motors were developed, they became the predominant type, particularly on longer routes. High voltages are used because this allows the use of low currents; transmission losses are proportional to the square of the current. Thus, high power can be conducted over long distances on lighter and cheaper wires. Transformers in the locomotives transform this power to a low voltage and high current for the motors. A similar high voltage, low current system could not be employed with direct current locomotives because there is no easy way to do the voltage/current transformation for DC so efficiently as achieved by AC transformers.
AC traction still occasionally uses dual overhead wires instead of single-phase lines. The resulting three-phase current drives induction motors, which do not have sensitive commutators and permit easy realisation of a regenerative brake. Speed is controlled by changing the number of pole pairs in the stator circuit, with acceleration controlled by switching additional resistors in, or out, of the rotor circuit. The two-phase lines are heavy and complicated near switches, where the phases have to cross each other. The system was widely used in northern Italy until 1976 and is still in use on some Swiss rack railways. The simple feasibility of a fail-safe electric brake is an advantage of the system, while speed control and the two-phase lines are problematic.
s with DC motors.
Rectifier locomotives, which used AC power transmission and DC motors, were common, though DC commutators had problems both in starting and at low velocities. Today's advanced electric locomotives use brushless three-phase AC induction motors. These polyphase machines are powered from GTO-, IGCT- or IGBT-based inverters. The cost of electronic devices in a modern locomotive can be up to 50% of the cost of the vehicle.
Electric traction allows the use of regenerative braking, in which the motors are used as brakes and become generators that transform the motion of the train into electrical power that is then fed back into the lines. This system is particularly advantageous in mountainous operations, as descending locomotives can produce a large portion of the power required for ascending trains. Most systems have a characteristic voltage and, in the case of AC power, a system frequency. Many locomotives have been equipped to handle multiple voltages and frequencies as systems came to overlap or were upgraded. American FL9 locomotives were equipped to handle power from two different electrical systems and could also operate as diesel-electrics.
While today's systems predominantly operate on AC, many DC systems are still in use – e.g., in South Africa and the United Kingdom ; Netherlands, Japan, Ireland ; Slovenia, Belgium, Italy, Poland, Russia, Spain and Washington, D.C..

Power transmission

Electrical circuits require two connections. From the beginning, the track was used for one side of the circuit. Unlike model railroads the track normally supplies only one side, the other side of the circuit being provided separately.

Overhead lines

Railways generally tend to prefer overhead lines, often called "catenaries" after the support system used to hold the wire parallel to the ground. Three collection methods are possible:
Of the three, the pantograph method is best suited for high-speed operation. Some locomotives use both overhead and third rail collection.
In Europe the recommended geometry and shape of pantographs are defined by standard EN 50367/IEC 60486

Third rail

The original Baltimore and Ohio Railroad electrification used a sliding shoe in an overhead channel, a system quickly found to be unsatisfactory. It was replaced by a third rail, in which a pickup rode underneath or on top of a smaller rail parallel to the main track, above ground level. There were multiple pickups on both sides of the locomotive in order to accommodate the breaks in the third rail required by trackwork. This system is preferred in subways because of the close clearances it affords.

Driving the wheels

During the initial development of railroad electrical propulsion, a number of drive systems were devised to couple the output of the traction motors to the wheels. Early locomotives often used jackshaft drives. In this arrangement, the traction motor is mounted within the body of the locomotive and drives the jackshaft through a set of gears. This system was employed because the first traction motors were too large and heavy to mount directly on the axles. Due to the number of mechanical parts involved, frequent maintenance was necessary. The jackshaft drive was abandoned for all but the smallest units when smaller and lighter motors were developed,
Several other systems were devised as the electric locomotive matured. The Buchli drive was a fully spring-loaded system, in which the weight of the driving motors was completely disconnected from the driving wheels. First used in electric locomotives from the 1920s, the Buchli drive was mainly used by the French SNCF and Swiss Federal Railways. The quill drive was also developed about this time and mounted the traction motor above or to the side of the axle and coupled to the axle through a reduction gear and a hollow shaft - the quill - flexibly connected to the driving axle. The Pennsylvania Railroad GG1 locomotive used a quill drive. Again, as traction motors continued to shrink in size and weight, quill drives gradually fell out of favour.
Another drive was the "bi-polar" system, in which the motor armature was the axle itself, the frame and field assembly of the motor being attached to the truck in a fixed position. The motor had two field poles, which allowed a limited amount of vertical movement of the armature. This system was of limited value since the power output of each motor was limited. The EP-2 bi-polar electrics used by the Milwaukee Road compensated for this problem by using a large number of powered axles.
Modern electric locomotives, like their Diesel-electric counterparts, almost universally use axle-hung traction motors, with one motor for each powered axle. In this arrangement, one side of the motor housing is supported by plain bearings riding on a ground and polished journal that is integral to the axle. The other side of the housing has a tongue-shaped protuberance that engages a matching slot in the truck bolster, its purpose being to act as a torque reaction device, as well as a support. Power transfer from motor to axle is effected by spur gearing, in which a pinion on the motor shaft engages a bull gear on the axle. Both gears are enclosed in a liquid-tight housing containing lubricating oil. The type of service in which the locomotive is used dictates the gear ratio employed. Numerically high ratios are commonly found on freight units, whereas numerically low ratios are typical of passenger engines.

Wheel arrangements

The Whyte notation system for classifying steam locomotives is not adequate for describing the variety of electric locomotive arrangements, though the Pennsylvania Railroad applied classes to its electric locomotives as if they were steam. For example, the PRR GG1 class indicates that it is arranged like two 4-6-0 class G locomotives coupled back-to-back.
UIC classification system was typically used for electric locomotives, as it could handle the complex arrangements of powered and unpowered axles and could distinguish between coupled and uncoupled drive systems.

Battery locomotive

A battery-electric locomotive is powered by on-board batteries; a kind of battery electric vehicle.
Such locomotives are used where a diesel or conventional electric locomotive would be unsuitable. An example is maintenance trains on electrified lines when the electricity supply is turned off. Another use for battery locomotives is in industrial facilities where a combustion-powered locomotive could cause a safety issue due to the risks of fire, explosion or fumes in a confined space. Battery locomotives are preferred for mines where gas could be ignited by trolley-powered units arcing at the collection shoes, or where electrical resistance could develop in the supply or return circuits, especially at rail joints, and allow dangerous current leakage into the ground. Mine railways often use battery locomotives.
The first electric locomotive built in 1837 was a battery locomotive. It was built by chemist Robert Davidson of Aberdeen in Scotland, and it was powered by galvanic cells. Another early example was at the Kennecott Copper Mine, Latouche, Alaska, wherein 1917 the underground haulage ways were widened to enable working by two battery locomotives of. In 1928, Kennecott Copper ordered four 700-series electric locomotives with onboard batteries. These locomotives weighed and operated on 750 volt overhead trolley wire with considerable further range whilst running on batteries. The locomotives provided several decades of service using Nickel-iron battery technology. The batteries were replaced with lead-acid batteries, and the locomotives were retired shortly afterward. All four locomotives were donated to museums, but one was scrapped. The others can be seen at the Boone and Scenic Valley Railroad, Iowa, and at the Western Railway Museum in Rio Vista, California.
The Toronto Transit Commission previously operated a battery electric locomotive built by Nippon-Sharyo in 1968 and retired in 2009.
London Underground regularly operates battery-electric locomotives for general maintenance work.

Electric locomotives around the world

Europe

Electrification is widespread in Europe. Due to higher density schedules, operating costs are more dominant with respect to the infrastructure costs than in the U.S. and electric locomotives have much lower operating costs than diesel. In addition, governments were motivated to electrify their railway networks due to coal shortages experienced during the First and Second World Wars.
Diesel locomotives have less power compared to electric locomotives for the same weight and dimensions. For instance, the 2,200 kW of a modern British Rail Class 66 diesel locomotive was matched in 1927 by the electric SBB-CFF-FFS Ae 4/7, which is lighter. However, for low speeds, tractive effort is more important than power. Diesel engines can be competitive for slow freight traffic but not for passenger or mixed passenger/freight traffic like on many European railway lines, especially where heavy freight trains must be run at comparatively high speeds.
These factors led to high degrees of electrification in most European countries. In some countries like Switzerland, even electric shunters are common and many private sidings are served by electric locomotives. During World War II, when materials to build new electric locomotives were not available, Swiss Federal Railways installed electric heating elements in the boilers of some steam shunters, fed from the overhead supply, to deal with the shortage of imported coal.
Recent political developments in many European countries to enhance public transit have led to another boost for electric traction. In addition, gaps in the un-electrified track are closed to avoid replacing electric locomotives by diesel for these sections. The necessary modernization and electrification of these lines is possible due to the financing of the railway infrastructure by the state.
British railways have a number of electric locomotive classes: Class 76, Class 86, Class 87, Class 90, Class 91, Class 92.

Russia and former USSR

and other countries of the former USSR have a mix of 3,000 V DC and 25 kV AC for historical reasons.
The special "junction stations" have wiring switchable from DC to AC. Locomotive replacement is essential at these stations and is performed together with the contact wiring switching.
Most Soviet, Czech, Russian and Ukrainian locomotives can operate on AC or DC only. For instance, VL80 is an AC machine, with VL10 a DC version. There were some half-experimental small series like VL82, which could switch from AC to DC and were used in small amounts around the city of Kharkov in Ukraine. Also, the latest Russian passenger locomotive EP10 is dual-system.
Historically, 3,000 V DC was used for simplicity. The first experimental track was in Georgian mountains, then the suburban zones of the largest cities were electrified for EMUs - very advantageous due to much better dynamic of such a train compared to the steam one, which is important for suburban service with frequent stops. Then the large mountain line between Ufa and Chelyabinsk was electrified.
For some time, electric railways were only considered to be suitable for suburban or mountain lines. In around 1950, a decision was made to electrify the highly loaded plain prairie line of Omsk-Novosibirsk. After this, electrifying the major railroads at 3,000 V DC became mainstream.
25 kV AC started in the USSR in around 1960, when the industry managed to build the rectifier-based AC-wire DC-motor locomotive. The first major line with AC power was Mariinsk-Krasnoyarsk-Tayshet-Zima; the lines in European Russia like Moscow-Rostov-on-Don followed.
In the 1990s, some DC lines were rebuilt as AC to allow the usage of the huge 10 MWt AC locomotive of VL85. The line around Irkutsk is one of them. The DC locomotives freed by this rebuild were transferred to the St Petersburg region.
The Trans-Siberian Railway has been partly electrified since 1929, entirely since 2002. The system is 25 kV AC 50 Hz after the junction station of Mariinsk near Krasnoyarsk, 3,000 V DC before it, and train weights are up to 6,000 tonnes.

North America

Canada

Historically, Canada has used a variety of electric locomotives, primarily for moving passengers and cargo through poorly ventilated tunnels. Electric locomotives that were in use in Canada include the St. Clair Tunnel Co. Boxcab Electric, CN Boxcab Electric, and GMD GF6C. Similar to the US the flexibility of diesel locomotives and the relatively low cost of their infrastructure has led them to prevail except where legal or operational constraints dictate the use of electricity. Leading to limted electric railway infrastructure and by extension electric locomotives operating in Canada today. Two examples exist today:
In the future Toronto's GO Transit plans to operate a fleet of new electric locomotives as a part of its Regional Express Rail initiative. The feasibility of using hydrogen fuel-cell locomotives is also being studied.

United States

Electric locomotives are used for passenger trains on Amtrak's Northeast Corridor between Washington, DC, and Boston, with a branch to Harrisburg, Pennsylvania, and on some commuter rail lines. Mass transit systems and other electrified commuter lines use electric multiple units, where each car is powered. All other long-distance passenger service and, with rare exceptions, all freight is hauled by diesel-electric locomotives.
In North America, the flexibility of diesel locomotives and the relatively low cost of their infrastructure has led them to prevail except where legal or operational constraints dictate the use of electricity. An example of the latter is the use of electric locomotives by Amtrak and commuter railroads in the Northeast. New Jersey Transit New York corridor uses ALP-46 electric locomotives, due to the prohibition on diesel operation in Penn Station and the Hudson and East River Tunnels leading to it. Some other trains to Penn Station use dual-mode locomotives that can also operate off third-rail power in the tunnels and the station. Electric locomotives are planned for the California High-Speed Rail system.
During the steam era, some mountainous areas were electrified but these have been discontinued. The junction between electrified and non-electrified territory is the locale of engine changes; for example, Amtrak trains had extended stops in New Haven, Connecticut, as locomotives were swapped, a delay which contributed to the decision to electrify the New Haven to Boston segment of the Northeast Corridor in 2000.

Asia

China

China has over of electrifed railway. With most trunk line heavy freight and long distance passenger trains operated using high power electric locomotives, typically in excess of of power output.

India

All mainline electrified routes in India use 25 kV AC overhead electrification at 50 Hz. As of March 2017, Indian railways haul 85% of freight and passenger traffic with electric locomotives and 30,000 km of railway lines have been electrified.

Japan

Japan has come close to complete electrification largely due to the relatively short distances and mountainous terrain, which make electric service a particularly economical investment. Additionally, the mix of freight to passenger service is weighted much more toward passenger service than in many other countries, and this has helped drive government investment into the electrification of many remote lines. However, these same factors lead to operators of Japanese railways to prefer EMUs over electric locomotives. Religating electric locomotives to freight and select long distance services, making the vast majority of electric rolling stock in Japan being operated with EMUs.

Pakistan

has 29 electric locomotives of class BCU30E numbered 7001–29. These are British-built locomotives of 3,000 horsepower for 25 kV AC. The electric locomotives were introduced in 2009 for the 286 kilometres Lahore-Khanewal junction in order to modernize the system and save scarce foreign exchange required for import of fuel for diesel locomotives. They are stored out of use because the overhead lines are un-serviceable, owing to large theft of copper.

Australia

Both Victorian Railways and New South Wales Government Railways, which pioneered electric traction in Australia in the early 20th century and continue to operate 1,500 V DC Electric Multiple Units, have withdrawn their electric locomotives.
In both states, the use of electric locomotives on principal interurban routes proved to be a qualified success. In Victoria, because only one major line had been electrified, the economic advantages of electric traction were not fully realized due to the need to change locomotives for trains that ran beyond the electrified network. VR's electric locomotive fleet was withdrawn from service by 1987 and the Gippsland line electrification was dismantled by 2004. The 86 class locomotives introduced to NSW in 1983 had a relatively short life as the costs of changing locomotives at the extremities of the electrified network, together with the higher charges levied for electricity use, saw diesel-electric locomotives make inroads into the electrified network. Electric power car trains are still used for urban passenger services.
Queensland Rail implemented electrification relatively recently and utilises the more recent 25 kV AC technology with around 1,000 km of the narrow gauge network now electrified. It operates a fleet of electric locomotives to transport coal for export, the most recent of which the 3,000 kW 3300/3400 Class. Queensland Rail is currently rebuilding its 3100 and 3200 class locos into the 3700 class, which use AC traction and need only three locomotives on a coal train rather than five. Queensland Rail is getting 30 3800 class locomotives from Siemens in Munich, Germany, which will arrive during late 2008 to 2009. QRNational has increased the order of 3800 class locomotives. They continue to arrive late into 2010.